Causes of the problem
Before proceeding with self-repair, you need to understand the reason why the tablet does not start. Among the most common reasons are:
- Discharging the battery to zero. In such a case, the iPad boots up to the apple and then turns off.
- Operating system problems. If the screen lights up, but the tablet does not work, try to return it to a working state by a forced reboot or flashing.
- Hardware problems caused by mechanical stress, moisture or other negative factors.
What to do if iPad does not turn on after mechanical impact, or the screen goes blank after turning on? It is recommended to contact a service center. Hardware problems can be very different:
- Defective power button. Find the breakage easily. Connect the charger to the device. if the indicator lights up, then the power button is faulty.
- Short circuit with damaged components. It will not be possible to identify the damaged area on your own.
- Liquid penetration into the housing.
Self-repair will result in the iPad being void of warranty, if any. In addition, you can damage other components by adding new problems to the existing ones.
Eliminate software errors
If the tablet does not boot due to hardware problems, then there is a high probability that the user will immediately understand this. The device will be completely inoperative, so even before loading an apple it will not come. If your iPad does not turn on, but only an apple is on, then try to fix the problem yourself. What to do:
- Force restart the tablet.
- Update or Reflash iPad via iTunes.
To force restart the device, press the Power and Home buttons. Keep them squeezed for 8-10 seconds until the tablet turns off completely. Then release the keys and wait for the system to boot. This method helps, even if the system is frozen tightly, or when turned on, the apple is on and the screen goes out.
What if, after a forced restart, the system stalled again during the boot phase? Try to update the system via iTunes while saving the data:
- Connect iPad to Computer with iTunes.
- Force restart by holding the keys until a recovery window appears in iTunes.
- Select the “Update” option.
ALL iPads Fixed: Not Rebooting, Black Screen, Won’t Turn On (2 Ways)
The program will independently download the latest version of iOS and install it on the tablet without touching the user’s personal data. If, for some reason, the update process takes more than 15 minutes, the tablet will exit recovery mode. In this case, repeat the procedure.
See also the earlier post on how to turn on your iPad if it doesn’t respond to normal boot. Right here.
iPad won’t turn on beyond the apple logo
If iPad does not turn on, apple is on, then serious hardware problems may be the reason. However, sometimes the problem occurs due to software errors and other failures that can be fixed without contacting a service center.
If after updating the problem is not resolved, the option remains with a flashing through iTunes. This operation will erase the user’s personal data from the iPad, so make sure you have a backup to iTunes or iCloud.
- Download the file with the latest iOS version for your model.
- Connect your tablet to iTunes.
- Open the device sync page.
- Hold down the Shift key on your keyboard and click “Restore”.
- Specify the path to the firmware file and confirm the restore request.
iTunes will delete the content that was stored on the tablet and download the new firmware to the internal memory. The settings will be reset to the factory state, so that all software problems will no longer interfere with the normal operation of the device.
If you can’t restore iPad in normal mode, you can try the same steps in DFU mode. To convert your tablet to DFU:
- Connect iPad to iTunes.
- Turn off your tablet.
- Hold Power, after 3 seconds hold Home.
- After 10 seconds, release Power while continuing to hold Home.
You need to keep Home until iTunes reports that the device is in recovery mode. Then you can start flashing iPad.
Other publications that will help you reflash iPad:
Reboot the device
Another way to restore any Apple smartphones, when the iPad does not turn on, the “apple” is on and off “, is to reboot the device. This is done in three steps:
- press the Home and Sleep keys at the same time
- hold them for 10-15 minutes until the “apple” logo appears on the display
- wait for the tablet to reboot
This reboot method restores almost all Apple gadgets in case of any software failure. This method is often used after installing a tweak from Cydia or a jailbreak, after which the iPad freezes quite often.
The very first thing to do, if the iPad does not turn on, the “apple” lights up, then goes out, is to check the state of charge of the device. It is possible that you missed the signal on the iPad screen that its battery is in a low state. At the same time, the charging icon itself may not blink. the iPad will react to a full discharge with a completely black display, on which the apple logo will appear only for a second. Even if the tablet “hangs on an apple”, the cause of the malfunction may be the same.
- connect an iPad, which has an “apple” on and then turns off, to a “native” charger (chargers from phones, iPad mini and other Apple gadgets are not suitable)
- wait at least 20 minutes
- start iPad again
The use of the “native” charger is extremely important. Analog chargers are capable of overheating the iPad while it is connected to the network, which leads to various problems in its operation. Incorrectly used iPads freeze when turned on and stop charging at all. IPhone and iPod freeze in the same way.
If after charging your iPad still does not turn on, also check that the charging cable and outlet are working properly. connect some other phone or smartphone to them and make sure that they are charging. If gadgets work with this cable and outlet, please go to other iPad recovery methods.
iPad won’t turn on, apple is on and off
If you are faced with a situation where your favorite iPad does not turn on, the “apple” is on and off, do not rush to carry the device to the service center. There are several ways in which it is possible to restore the tablet to work at home.
Flashing the gadget via iTunes
This is a rather aggressive way of dealing with software bugs, but if the iPad “hangs on the apple” and stubbornly does not turn on, then flashing is the last thing you can try at home. The method is bad in that you run the risk of erasing all or part of the data on your device after updating the iPad. This will happen if you have not backed up iPad to iTunes in the recent past.
Re-flashing in situations where the iPads freeze when turned on is performed in several stages:
- install the latest version of iTunes on your computer
- connect the iPad to the PC, which turns off or constantly reboots on the “apple“
- select the appropriate device type in the program settings and wait for the program to download the latest software version for it
- simultaneously press and hold the power and Home buttons on the iPad. an “apple” will appear on the iPad screen, which will go out
- follow the instructions in the iTunes dialog that opens on the PC screen
The program will prompt you to set up an iPad that is frozen and does not turn on as brand new (with a return to factory settings and a complete loss of all data) or restore the last backup.
Repair for mechanical damage
All described methods are suitable for home DIY repair of an iPad that is frozen and won’t turn on, provided that the damage to the device was not mechanical. If your tablet has turned off and no longer boots after it fell, then the reason for the constant reboot of the device may be an interrupted cable.
Additional signs of this are the following interference:
- when turned on, the screen lights up and flashes
- there are streaks and other imperfections in the image before it fades
- the appearing “apple” has a fuzzy white color
If your iPad goes out due to mechanical damage, do not repair the device yourself. Try restarting your tablet or charging it as described above, then flashing the device. If none of the methods helped, and the iPad restarts and goes dead, take it to the service center.
The most profitable option is to entrust the repair of a non-bootable iPad to the Yuda performers. They will restore the tablet, which does not turn on and does not charge, as quickly as possible right at your home:
- solder the dangling cable
- will replace the broken glass of the screen
- carry out professional software installation
Option 1. Hard Reset
We turn off the iPhone using the Hard Reset method, that is, the so-called “hard reset”. To do this, you need to simultaneously hold down and hold down two buttons for 10 seconds: Home and Power. Keep out until the device turns on.
Option 2. Reinstall iOS
If the first method did not help, you should try reinstalling the software on the iPhone. To do this, the iPhone launches in DFU mode. This is done like this. we connect the smartphone to the computer and launch the iTunes program. Next, hold down the Power and Home buttons. You need to hold it for about ten seconds. After this time, only the Power button must be released. After that, iTunes should see the device (the screen will remain dark).
Well, then the program should offer to restore the device from a backup and reinstall iOS.
Then, after the device is restored. make a software update.
The iPhone does not turn on but the apple is on the screen. What to do?!
Popular smartphones from Apple, whatever one may say, this is the same computer, albeit a mobile one. And with him, like other representatives of this class of devices, troubles can happen. both hardware and software. One of the common reasons that can happen to them is when the iPhone does not turn on, but the apple is on after pressing the Power button.
People call this unpleasant problem the “white apple“. In fact, this is a certain state of the iPhone, which is characterized by the display of the company’s logo on the screen (a bitten glowing apple) when trying to turn on the smartphone. In this case, further loading of the device does not continue. At the same time, he does not react to anything and, as usual, does not turn off. How to be?
The easiest thing to try is a Hard Reset. But, let’s take our time and consider all the options in order.
So, what can you do to restore the phone’s performance if the iPhone does not turn on, the apple is on?!
There are such methods:
Option 3. Picking Cydia
This method is an alternative to the previous one in the event that you do not want to restore the device or for some reason cannot do it while the iPhone does not turn on and off, but the glowing apple is on.
Here I will make a small lyrical digression. The fact is that very often the reason that the iPhone does not turn on is the installation of some third-party application, which either did not get up correctly, or does not work correctly. Then you should try to remove it and restart your smartphone. Another equally common reason is Cydia tweaks.
My iPad Won’t Turn On! Here’s The Real Fix.
To restore the performance of the iPhone, which has an apple on the screen and does not disappear, let’s try to load it without Cydia tweaks. To do this, turn off the device, press the volume up button. “” And hold it down, wait until iOS boots up without Cydia tweaks. If the download is successful in this mode, the reason is clearly in the last installed Tweak. Delete it and the device will work again.
If it still does not boot, then restart it again. Then after 5 minutes try to call your iPhone.
If you manage to get through. great! This indicates that the phone’s loading is interrupted at the very last moment of the OS launch. Then you need to try to access the file system through the iTools or iFunBox programs and use them to look for the files that are responsible for the malfunction.
Otherwise, whether you like it or not, in order to remove the burning apple on the phone screen, you still have to reinstall the IOS using the method I described earlier.
Note: This instruction is suitable not only for smartphones iPhone 4, 5 or 6, but also for iPad tablets, because both there and there one operating system is installed, which means that an apple can burn on the iPad and it does not turn on and does not turn off.
Good luck and stable work!
If the first method did not work. the iPad still does not load, the apple is on, you can try the second method. This method is considered more literate, but it is a little more difficult for new users of Apple devices:
- We connect the device to the PC and launch iTunes.
- Turn off the device and wait until the shutdown process is completed correctly.
- We press on the “Power” button, and after three seconds. “Home”. Hold the keys at the same time.
- After 10 seconds, release the power button, but continue to hold “Home”.
At the end of the procedure for entering the special mode, a message will appear in the iTunes application that the program has found your device in a recovery state. However, you will need to restore your iPad before using it with iTunes at the same time.
The same procedure can be performed in the case when the iPad 2 does not turn on, the apple is on.
How to troubleshoot
There are the following ways to fix the problem when iPad won’t turn on, apple is on:
- Follow Apple Support Best Practices.
- Entering the device into DFU mode.
It’s better to use the first method for a start. If there is no result, it is worth resorting to the second. It should be added that there are two options for entering iPad into special mode. at the end of the article we will consider how to do this.
The easiest way to enter a device into DFU is to simultaneously hold down the Home key and the power button for 10 seconds. Then you need to release the power key and continue to hold the “Home” button.
Apple Support Best Practices
If during startup for a long period of time the iPad does not load, the apple is on, you need to do the following:
- Connect the gadget to the PC and open iTunes.
- Perform a forced restart (press and hold the Sleep / Wake and Home keys at the same time).
- Under no circumstances release the keys after the company logo reappears on the display. the key combination must be held until the recovery mode screen appears.
- On the screen that appears prompting you to restore or start the update process, select the “Update” function. The app must reinstall iOS while saving data.
The Apple app must download the software for the device. If for some reason the procedure takes more than 15 minutes, the tablet will exit the recovery process, then you will need to repeat all the steps again.
The above tips will also come in handy for the owners of “apple” devices, which do not turn on the iPad 2, the apple is on the screen.
Switching to DFU mode
It is worth noting that this is a more extreme way out of the situation when the apple is on, but the iPad does not turn on. There are two methods for entering a gadget into a special mode.
If the apple logo is lit on the display and the iPad won’t turn on
Almost every owner of the popular “apple” tablet at least a couple of times had to deal with failures during the operation of the device. It happens that the iPad does not turn on, the apple on the display is on. The problem is not that uncommon, so Apple Support has prepared several recommendations in case of such complaints from iPad owners.
Causes of the problem
Among the reasons for such failures are:
- interruptions during an iOS update;
- incorrect installation of programs;
- moisture penetration into the device;
- processor malfunction.
Exit DFU Mode
You can exit with a normal reboot. You need to hold down the Home and Power keys for 10 seconds. The tablet will reboot and work normally. If the cable is connected, after holding “Home” and “Power” for 10 seconds, the device may not start. In this case, just press the “Power” button. the device should turn on.
So do not panic if the iPad does not turn on and the apple is on, because you already know what to do in this case.
Check for physical damage or fluid damage
iPhone won’t turn on after update or water damage
Another reason why your iPhone won’t turn on. physical and water damage. Even a drop of water in the charging port could mean the iPhone isn’t charging. Examine your iPhone carefully for damage. Your secondary phone can be replaced under warranty. If fluid damage is present, you may be eligible for Apple Care, but you still have to pay the costs. Read Apple’s article on how to check if your iPhone is fluid damaged.
Learn how to replace the Home button yourself
If your iPhone is less than a year old, it may still be covered by Apple’s one-year warranty, which means you can make an appointment at the Genius Bar at your nearest Apple Store to have your Home button fixed for free.
Unfortunately, most iPhones with a physical Home button are over a year old, but you can still pay for repairs from Apple or a third-party service provider.
However, it is usually cheaper to repair it yourself, and there are many websites that teach you how to repair gadgets. Some of them even sell all the parts and tools needed for a particular repair. Just be careful not to miss a step or make the problem worse.!
7 underground torrent sites to get uncensored content
You need specialized search engines to find legal torrents, locked houses, public records, and even UFOs.
About the author Dan Heler (Published 164 articles)
Dan writes tutorials and troubleshooting guides to help people get the most out of their technology. Before becoming a writer, he earned a bachelor’s degree in audio technology, supervised renovations at an Apple Store, and even taught English in China.
Iphone does not turn on the apple is on and goes out
In the modern world, a smartphone is an integral part of our life, however, we never know at what point it will stop working. Agree there was not a day when you plan your activities and think about whether the iphone will work tomorrow? is not it? Yes, today we will talk about an Apple product, namely the iphone.
If an apple is on on the iphone 7 and does not turn on, then the following repair tools are needed:
How to disassemble the iphone can be found here.
We take out the old battery, carefully (the main thing is not to damage the cable), install a new one in your device, turn it on, disassembled, check the work and put it back together. It should be noted that you cannot use household household double-sided tape and PVC foam tape to fix the battery. Too thick tape can damage the screen matrix during assembly by putting a lot of pressure on the sensing element.
This problem is inherent in all models of the brand due to the identity of the chemical composition of the battery, in other words, all batteries of the “li-ion” technology are identical, so the iPhone 4s, se, x will also show the apple splash screen.
This is one of the most common reasons your iPhone keeps turning off and on. If you recently tried to update your iPhone to the new iOS 14/13 and the process stalled halfway or the update failed, this could cause the iPhone to keep shutting down and back on again.
Check your iPhone charger and Lightning cable.
The iPhone charger is broken. the device is not charging
Try charging your device with a different cable and replace the iPhone charger. Also test your own cable and charger by charging someone else’s device. If another device is charging, try charging your iPhone via your computer using a USB cable and use a wall charger if you frequently charge your iPhone using your laptop.
iPhone won’t turn on or charge? Here are 4 ways to fix
Have you been seeing a blank screen on your iPhone lately? This means your iPhone won’t turn on. The good news is that this post is dedicated to solving this problem. But first, you need to determine the reason why your iPhone won’t turn on. We will list the main causes of the problem, as well as suggest solutions for them. It might be a hardware or software issue that is why your iPhone won’t turn on. Let’s start with software issues because they are easier to fix than hardware issues.
Fix iPhone won’t turn on. Works for iPhone 7 Plus, 7, 6S, SE, 6 Plus, 6, 5S, 5C, 4S, 4 and all iPad models
iPad won’t turn on, apple is on and off
- oneFree diagnostics brought-
device you or our courier.
- 2We make repairs and also give a guarantee for newly installed parts. On average, repairs take 20-30 minutes.
- 3Get a working device yourself or call our courier.
Craftsmen who constantly encounter a malfunction when an apple burns, but the iPad does not turn on, distinguish three main reasons for the breakdown:
- software crashes;
- damaged firmware;
- hardware failures caused by moisture, drops, or impacts;
Many users claim that their iPad 1 can work without reboots for a month or two. Of course, during this period, the device receives a colossal amount of data that needs to be “digested”.
As a result, during a forced reboot, a nuisance often occurs in which an apple burns. In this case, you can restore performance in several ways:
- forced reboot;
- recovery via iTunes;
- flashing device.
The first method in many cases allows you to return the device to normal mode. But sometimes a forced reboot only makes the problem worse.
Apple does not turn on and burns on iPad 4, 3, 2, 1
Often, iPad 4 owners can face a problem when the tablet is frozen on an apple. What to do in such a situation, and why this malfunction occurs?
- We’ve been fixing Apple for 5 years. thousands of satisfied customers
- Repair with you. We manage to do 72% of repairs in 35 minutes
- Free diagnostics
- Original spare parts
- Guarantee for all works
IPad Repair Cost
Important! The price of repair already includes the cost of spare parts and the cost of work.
iPad stuck on apple and won’t turn on. What to do?
If, after restarting, the device hangs as before, or does not turn on at all, then try connecting it to the computer and restoring the system through iTunes. When this does not help, you should change the firmware. You can do this yourself, but it is better to entrust this laborious and responsible process to the masters of our Apple technology service center. Here, only verified and licensed software will be installed on the tablet.
But there are situations when the flashing does not bring a positive effect, but the malfunction remains further, the iPad does not turn on, the apple burns and goes out. This testifies to only one thing. there was a hardware failure and damage to key components of the device. You could inadvertently hit the tablet on an object, or the gadget could fall. All this often leads to damage to cables, microcircuits and even the motherboard.
How to fix an iPad 3 tablet in this situation? Most often, if the iPad 2 hangs on an apple, it indicates a failure of flash microcircuits or a processor. It is unlikely that it will be possible to restore these components on their own after damage, so it is necessary to completely replace them. This is a rather complex process that only a qualified employee with the necessary set of tools can perform.
But the biggest danger to the electronics of the device lies in moisture. The ingress of water leads to oxidation and corrosion of the contacts and microcircuits of the device. In addition, attempts to start the tablet after getting wet can end up with serious consequences for the device, because moisture, as an excellent conductor, leads to such a phenomenon as a “short circuit”. In this situation, the user will not fix anything on his own, you need to immediately contact our Apple repair shop.
Why does the iPhone turn itself off and on?
If the iPhone turns on and off immediately, then the reason for this may be: Deterioration of the battery. Its current voltage is simply not enough to initialize the device (it must be at least 2.5V), which is why when trying to start the OS, the device turns off.
What to do if iPhone turns on, shows apple and turns off?
Press and hold the Home and Power buttons on iPhone at the same time for 10 seconds. Then release the Power button and continue holding the Home button until iTunes detects the device in recovery mode (about 10 seconds).
What to do if iPhone flashes apple?
launch iTunes on the PC connect your device (the Apple logo should appear on the screen) turn off the device by pressing the Home and Power buttons at the same time. release the power button after the screen turns off (the icon should not light up)
What to do if iPhone 6 turns on and off?
The “apple” is constantly lit on the phone screen
- make sure the battery is charged and not discharged anytime soon
- prepare your computer and USB cable
- sync iPhone to PC
- turn off your iPhone while holding down the Home button and the Power button.
- hold down the power button and wait for the iTunes application logo to appear on the screen.
What to do if iPhone 7 is frozen on an apple?
To restart iPhone 7 and iPhone 7 Plus, press and hold the Volume Down buttons and the Power key for about 10 seconds. If the model is older, then to restart you need to hold down the power key and the Home button for 10 seconds until the apple icon disappears.
How to prevent iPhone from turning on when charging?
The simplest thing you can do is restart your phone by pressing and holding the Home button and the screen lock button. If this does not help, then try putting on charge and letting it charge.
One of the reasons the iPad won’t turn on is moisture getting into the case, the middle of the device. Moisture is the main enemy of any electronic gadget. No one is immune from such a nuisance. You can accidentally spill a drink on the iPad, drop the tablet into water, which will inevitably lead to failure of the microcircuit, loop, or other element of the internal board.
In this case, you need to disassemble the tablet, leaving it to dry for several days. Do not try to heat the device over gas, do not place near heaters. But it must be borne in mind that if moisture gets in, oxidation of the board is possible. Such repairs are expensive, so if there is a suspicion that moisture has got into the device, seek help from specialists.
iPad won’t turn on but apple is displayed
It often happens that the iPad does not start, but the apple logo is displayed on the display. Perhaps nothing serious happened to your device. You can independently restore the device to work.
The most common reason is software crash, malfunction. Reinstallation, flashing of the “apple” device, radical restoration of the “operating system” through iTunes will help to solve the problem. How to install and configure iTunes can be found in this article on our website.
- Connect iPad to PC via USB cable.
- Launch iTunes on PC (CTRLS keys). go to the side menu, in the “Overview” tab we find your device.
- On the iPad, simultaneously hold down the Home keys and the power button for 10 seconds.
- The iOS recovery notification should be displayed.
If the iPad does not turn on, but the apple is on, perhaps the internal elements of the motherboard, the central processor, or the touchscreen processing system have come out of the standing position. Comprehensive diagnostics will help to determine the malfunction. To avoid damaging the device, take it to a service center.
Connector problems, short circuit
If the charging connector is damaged, nothing will happen after connecting the charger. It is rather difficult to determine the cause on your own. Deformation of pin-connectors occurs when the user is carelessly handling, violation of the operating conditions, the tablet falls from a height, an attempt is made to insert an incompatible charger into the connector.
There is a possibility that the device does not charge due to contamination of the connector, moisture on the contacts and cleaning the contacts or contacting a service center will help solve the problem. The connector cannot be repaired. Only replacing the defective part with a new one will help. In service centers, the replacement will take no more than an hour.
The reason for not turning on the iPad can be a short circuit, which can occur when using non-original “charging”. It must be remembered that the electric charge is transferred to the power connector, other accessories. The problem can be solved only by replacing the defective parts in authorized service centers in your city.
IPad on / off key wear
Any keys of electronic devices are subjected to mechanical stress during operation, so it is possible that sooner or later they may fail. If the device falls face down, the power button or the loop responsible for its performance may fail.
The elimination of the malfunction will be carried out by the service center masters by replacing the faulty elements.
What to do if iPad won’t turn on
What to do if iPad won’t turn on. How to restore the working capacity of the “apple” device? Causes, options and solutions to the problem.
Owners of tablet computers from Apple operating on the basis of the iOS OS are accustomed to the stable, flawless operation of their gadgets. For this reason, any problems that arise during the operation of the iPad (2,3, Mini, Air) not only confuse the user, but also raise many questions. For example, what if iPad won’t turn on? Yesterday, when working with the “apple” device, there were no problems, and today when you press the “Enable” button, the device does not respond and even on a black screen the apple logo does not appear.
First of all, do not panic, run to the service center, and even more so try to disassemble the device. In 95% of cases, this problem can be solved in a few minutes by restoring the performance of your gadget using the tips given in this review.
Reasons why iPad won’t turn on
Unfortunately, one of the most common problems across Apple’s tablet lineup is not turning them on. It is hard to disagree that the Apple device that has stopped running is not much more useful than its box. But if the iPad did not come back to life after repeatedly pressing the power button, you need to figure out what caused this “behavior” of your device.
There may be several options for such behavior of the gadget:
- malfunctions, failures in the OS;
- problems in software, firmware;
- malfunctions in the motherboard;
- damage to the power connector;
- wear of the power key;
- malfunction of iPad;
- moisture ingress into the device.
If iPad won’t turn on, check the battery level. Tablet, any other mobile device will not function if the battery is depleted. Connect the device to a power source and after 15-20 minutes press the “Enable” button. If the display shows a “red” battery, the charging indicator is on, everything is in order, continue to charge the “apple” device.
If the charge indicator is not displayed, you can change the power source by connecting the device to a different outlet. But if the iPad does not turn on after fully charging the battery, the problem may be with the power button itself.
Another step that can be taken to resuscitate the iPad is to simultaneously press the on / off button and the Home key, the so-called Hard Reset (reset to factory settings).
Hold down two buttons for ten seconds. If the Apple icon lights up on the display, everything is in order with the device, the device will boot and be ready to work.
If the problem is still not resolved, the iPad does not turn on, we will consider other solutions and options that will help restore your device to work.
To avoid malfunctions in the operation of the “apple” device, do not neglect the operating rules:
- Use only original accessories. charger, USB cable.
- Try not to allow mechanical damage, handle the device carefully, since subsequent repair, replacement of damaged elements can be quite expensive.
- Do not interfere with the OS, do not remove restrictions from the firmware, do not install unofficial versions of the system, incompatible software, applications. Performing self-tailoring of the system, you act at your own peril and risk.
As you can see, there are a lot of reasons why the iPad won’t turn on. Therefore, if it was still not possible to determine why the iPad is not loading, the above tips did not help, contact a professional specialist, namely an authorized service center. In most cases, one cannot do without device diagnostics, which can only be performed using special devices.
Recovery Mode. Normal
The iPhone or iPad is entered into the usual recovery mode using simple steps, the sequence of these steps is described here. “How to enter iPhone into RM”. To exit the normal Recovery Mode, we simply left the iPhone for a while, it rebooted itself and exited recovery mode. To immediately exit recovery mode (so as not to wait), we simply forcibly rebooted the iPhone. It turns out that from the usual recovery mode, unlike others, it is quite easy to exit with a reboot.
Cord and iTunes icon on iPhone and iPad screen. Recovery Mode or Recovery Loop?
Friends, cases of the appearance of a USB cable and the iTunes icon on the screen of iPhones, iPads and iPods are quite common. In general, it is generally accepted that if a cord and an icon in the form of the iTunes program logo appear on the black display of one of these devices, then this means that Recovery Mode is running. But not everyone knows that the cable and iTunes, in addition to Recovery Mode, can mean Recovery Loop, which is different from the recovery mode.
In order for you to be able to make an accurate diagnosis, to determine the mode in which your iPhone (or other device) is displaying a USB cable and iTunes, we will write down the results of our research acquired as a result of the operation of these mobile Apple devices. And maybe our meager knowledge will help at least someone solve their problem and restore the phone or tablet to work.
Recovery Loop Mode. Compliant
There are cases that after a forced reboot, which is used to exit the normal recovery mode, the iPhone still continues to load a black screen, on which we see the cord and iTunes again and again. This situation means that the iPhone has entered the so-called Recovery Loop mode. A phone or tablet in this mode is very often driven by the iTunes program. Getting into the Recovery Loop can happen for various reasons, for example, as a result of errors when updating or restoring iOS firmware. A recovery loop can occur as a result of a software, hardware or household failure (for example, the cable was accidentally pulled out), once we ourselves put the iPhone into Recovery Loop mode when we tried to downgrade the iOS firmware from 7 to 6.
Why did we add the word “Obedient” in the subheading? Yes, because you can still get out of the obedient recovery loop and return the iPhone to a working state without losing information, for this we used the TinyUmbrella program, some users with TinyUmbrella had difficulties, and we found a more convenient way to exit the Recovery Loop using the program RedSn0w. There are other programs to exit the loop. iReb and RecBoot.
Recovery loop mode. not obedient
If your iPhone or iPad falls into a naughty Recovery Loop, then, as a rule, not only a forced restart is powerless, but the programs redsn0w, iReb, TinyUmbrella and RecBoot also cannot get the iPhone out of the recovery loop. As a result of using the programs above, the iPhone continues to display the USB cable and iTunes logo after reboot. In this case, we did not succeed in avoiding the loss of information stored in the iPhone, but it’s good if you also made a backup copy earlier.
If you have caught a naughty recovery loop, then all that remains is to connect your iPhone to iTuens and try to flash it. Sometimes the phone cannot be flashed in this mode, then it is put into DFU mode and again they try to flash it. As a result, the iPhone firmware erases all information, and we restore it from the backup made earlier. It happens that after flashing the iPhone or iPad, they are asked to enter someone’s Apple ID and password, but this is a completely different story.