Canon Printer Does Not Print What To Do

How to fix the error if the device does not print in red

With the purchase of an Epson, HP or Canon all-in-one printer, users make a choice: contact the service center, if necessary, or carry out the procedures themselves. In the latter case, the likelihood of premature failure of the peripheral equipment is much greater.

Start of problems

There are no problems until the first replacement of consumables or cartridge. The owners strive to reduce the cost of paper and paint of different colors, including red, so they are replacing the original ones with analog ones. This often leads to printhead problems. Why doesn’t the product print in red? What can be a prerequisite for breakdowns?

They can be corrected by a competent diagnosis. Why do it? Finding the exact cause of the problem is the first step in the repair, the result of which is to return the printer to operating mode.

If the Epson Corporation printer does not print in red, then the problem is related to the color rendering, consumables such as red ink, or improper printer refilling. When diagnosing a problem, take into account the model of the printer, the type of cartridge, the correspondence of colors and reservoirs, the state of the printheads before refueling.

Possible reasons

Take for example a standard printer that can print in four colors. The containers for them are divided into two blocks: the first contains black paint, and the second contains cyan, red and yellow ink. The choice of such a color scheme is due to the ability to create the desired color shades with it.

Printer print head

The reason the Canon printer does NOT print in red is:

  • Air entering the cartridge. often this occurs when replacing original ink, cartridge and paper with analog.
  • Combination of cartridges from different manufacturers in one device. As a result, the printer identifies some, but does not notice the presence of the second.
  • Clogged nozzles in the print head. It is provoked by a simple peripheral equipment or an incorrectly selected red analog paint. To correct the situation, the print head is cleaned with a special liquid. It is made specifically for each brand (Canon, Epson), there are also universal cleaners. If they are absent, use distilled water.
  • Incorrect cartridge refilling order. This happens if the user first introduces red ink into the print head, rather than following the operating instructions.
  • Damage to the bridges between the tanks. The presence of such problems leads to mixing of paints of different colors located in the adjacent tanks.

If you are not confident in your own abilities, then neither try to adjust the peripheral equipment yourself. The risk of a worsening problem or permanent breakdown of your Canon Pixma MP250, HP or Epson will only increase.

Color adjustment utilities

This measure is, in fact, the easiest to implement. It is recommended to use it after checking the paint level in the tank. If the red ink has NOT run out yet, and the device does not print, then the driver for cleaning the PG is started. This is effective if a Canon, HP or Epson inkjet printer is rarely used for its intended purpose.

But neither program cleaning, nor other restorative measures will help those cartridges whose sponges have hardened, the electronics are damaged, and the nozzle sealing is broken.

Rinsing the cartridge containing the absorbent sponge

To begin with, the sponge is brought back to normal. To do this, you need to remove the PG from the printer, which does NOT print, and place it in a previously prepared solution of distilled water or purifying water. The cartridge is placed nozzles down.

READ  Pantum M6500 Printer Writes No Cartridge

The next step is to refill the cartridge. This should be done using a special suction cup or syringe. It is slowly PULLED back through smooth movements. Before installing the element back into the peripheral device, it is cleaned of excess paint. At the same time, attention is paid to the state of the contacts. They must NOT be damaged or stained with ink.

Flushing the printheads

If after 3 cleanings the device does not print or the quality of the resulting print is poor, then it remains to replace the cartridge. Unfortunately, Epson printers with this design require frequent replacement as they cannot be restored. The procedure is shown in the photo.

Reconditioning ink cartridges with vacuum retention

What to do in this case? Ghgs characterized by vacuum retention of ink are easier to reanimate. To begin with, 10 ml of cleaning solution is poured into the cartridge. After a couple of minutes, it should be shaken out of there. The procedure is repeated 3-4 times. After the cartridge is placed in the composition for washing for a day (nozzles down).

Next, you need to pour ink, stop air access to the cartridge and, using a special suction, remove from the nozzle NOT more than 10 ml of paint. If the process took place without complications, then it remains to carry out 3 purges of the steam generator and check the result by means of a test print.

Separate GHG purification

If problems with the ink reservoir are diagnosed, then comments make sense in repairing it. The print head can still be reanimated. They do this with the help of Special utilities, which are on the installation disk included with the Canon printer (Epson) when purchasing it.

In case it is useless, the PG is sorted out. In this case, you must follow the instructions. Otherwise, it is useless to hope for further operation of the equipment periphery. After that, 10 software cleanings are required. If the print result is NOT happy, then replace the main element of the Epson inkjet printer.

Ultrasonic cleaning with separate printheads is considered effective, but it is used only in a service center. If at home it was not possible to correct the situation, then they turn to professionals.

If the Epson printer prints in red, ignoring the rest of the ink, or vice versa, then check the condition of the reservoir, printheads or color settings. To avoid such problems, you should:

  • Install cartridges from one set and one manufacturer into peripheral equipment;
  • Performs a “nozzle test” and check the ink levels before cleaning the print heads. If it is below the minimum mark, then the canon and epson printers simply do not see that they are still there;
  • Choose only high-quality consumables for printing.

Why doesn’t the device print red in Epson, HP, Canon Pixma MP250? The exact answer to this question can be obtained only by Carrying out diagnostics. For the uninitiated, this task is not feasible due to the complexity of the printer design and the variety of types of cartridges. Therefore, in the absence of the appropriate skills, it is safer to entrust the work to the professionals of the Epson service center (HP, Canon).

DOES NOT print one of the colors

Possible reasons :. The CISS is NOT transferred from the transport position to the working position (small plugs (s) are closed). The ink cans are at a lower level than that required for the printer to function correctly;. Transferred Ink trail;. Out of ink;. Air in the ink plume;. The ink has dried up when the printer is not used for a long time.

Solution options:. Translate CISS into working position, install air filters;. Install ink cans correctly;. Pump the air or eliminate the squeezing of the plume;. Clean the print head using the driver;. Print a test page and check visually.

DOES NOT print one of the colors

Why doesn’t the product print in one color? There can be many reasons for this. Let’s figure it out.

DOES NOT print yellow? First of all, check if there is ink of this color in the system, because they may simply run out. It is also possible that the NPC system is not transferred from the transport position, its plugs are closed. If the printer is idle for a long time, ink can dry out. another cause of this problem. It can also be the reason that the device does not print in blue.

If you pinch the green channel of the ink plume, then, accordingly, the device does not print green. Also check the level of the outer paint cans. They MUST NOT be at a lower level with the printing unit.

READ  Canon Capt USB Device Does Not See Printer

If you do not print black, then perhaps the CISS is NOT switched to the working position or is at a lower level with the printer. A loopback can also be transmitted. Don’t forget that the system may simply run out of blue ink. Air in the train can also interfere with printing.

DOES NOT print red? It’s that simple! Either your CISS is not ready for work (its openings are closed), or its Ink loop is transmitted. It can also get air into it, which will prevent ink from entering the cartridge.

Check the ink level if the device does NOT print in pink! They just might not be enough. Or perhaps you have NOT used the printer for a long time, and the ink has dried up there.

How to solve the problem:

  • Check the ink level in the tanks near the printer (if less than 30%, then refueling is needed)
  • On tanks, large openings Must be closed and small openings.
  • There should not be any air gaps along the ink trail
  • You need to go to the printer menu and find the Setup item, then you need to select the 2nd item Tech. Maintenance and again the 2nd point Head Cleaning
  • Cleaning should be done 2 times, then DO NOT print for 40 minutes. A maximum of 5 cleanings can be performed per day.
  • If there are improvements after cleaning, then you need to contact the service center. When transporting, be sure to cover all openings on the ink tanks.

Possible reasons :. The CISS is NOT transferred from the transport position to the working position (small plugs (s) are closed). The ink cans are at a lower level than that required for the printer to function correctly;. Transferred Ink trail;. Out of ink;. Air in the ink plume;. The ink has dried up when the printer is not used for a long time.

Solution options:. Translate CISS into working position, install air filters;. Install ink cans correctly;. Pump the air or eliminate the squeezing of the plume;. Clean the print head using the driver;. Print a test page and check visually.

DOES NOT print one of the colors

Why doesn’t the product print in one color? There can be many reasons for this. Let’s figure it out.

DOES NOT print yellow? First of all, check if there is ink of this color in the system, because they may simply run out. It is also possible that the NPC system is not transferred from the transport position, its plugs are closed. If the printer is idle for a long time, ink can dry out. another cause of this problem. It can also be the reason that the device does not print in blue.

If you pinch the green channel of the ink plume, then, accordingly, the device does not print green. Also check the level of the outer paint cans. They MUST NOT be at a lower level with the printing unit.

If you do not print black, then perhaps the CISS is NOT switched to the working position or is at a lower level with the printer. A loopback can also be transmitted. Don’t forget that the system may simply run out of blue ink. Air in the train can also interfere with printing.

DOES NOT print red? It’s that simple! Either your CISS is not ready for work (its openings are closed), or its Ink loop is transmitted. It can also get air into it, which will prevent ink from entering the cartridge.

Check the ink level if the device does NOT print in pink! They just might not be enough. Or perhaps you have NOT used the printer for a long time, and the ink has dried up there.

How to solve the problem:

  • Check the ink level in the tanks near the printer (if less than 30%, then refueling is needed)
  • On tanks, large openings Must be closed and small openings.
  • There should not be any air gaps along the ink trail
  • You need to go to the printer menu and find the Setup item, then you need to select the 2nd item Tech. Maintenance and again the 2nd point Head Cleaning
  • Cleaning should be done 2 times, then DO NOT print for 40 minutes. A maximum of 5 cleanings can be performed per day.
  • If there are improvements after cleaning, then you need to contact the service center. When transporting, be sure to cover all openings on the ink tanks.

The printer does not print what should I do? Why does the Canon printer not print?

If ink is present in the cartridges, but the device does not print, this may be due to 3 reasons: Ink DOES NOT pass through the channels of the SG (clogging or airlock). Ink from the cartridge goes to the SG (the filler is forgotten or the air hole is closed).

READ  Software for printing photos on a Canon printer

Why doesn’t the printer print?

If the printer does not print, then the first thing you can do is restart it with the computer. Then, check the power cord and interface. USB: disconnect the power cord and reconnect it; reconnect USB cable.

How to reinstall the printer driver?

To get started open the “Control Panel” and click on “Devices and Printers”. Find your printer there and open the context menu by right-clicking on the printer. Remove the printer by selecting “Remove device” there. Then reconnect the printer to your computer.

What to do if the HP LaserJet p1102 printer does not print?

Initially, if the HP LaserJet p1102 product does NOT print, you need to check all connections. If the printer is connected to a network, try starting it by enabling the start button. Next, make sure the machine is connected by cable or wirelessly to the PC. The reliability of this connection should also be checked.

How to start the Canon printer?

Installing a Canon Printer

  • First of all, open the start menu and in the same place call the command printers and faxes.
  • On the screen you will see a window designed to work with this type of device.
  • In the left column of the window, select the command set printer.
  • Click on the “Next.
  • On the pages that open, you need to select the type of printer.

What to do if the Canon printer does not turn on?

The printer won’t turn on. what to do?

  • Make sure there is power to the home / office. If there is light, then you need to check the meter.
  • Examine the outlet. Burn marks on the outlet indicate a problem.
  • Check extension cord / surge protector / adapter.
  • Inspect the power supply.

Why does not the printer print a blank sheet?

The cartridge may also be to blame for why the printer prints blank pages. In the case of inkjet printers, a prerequisite for clean sheets may be clogged printhead nozzles. This prevents paint from being sprayed onto the paper. The solution to the problem will be to launch the cleaning system.

Why does not the printer print from the laptop?

Another common reason why the laptop does not find the printer is the wrong device selected in the printing tools. Select “Devices and Printers” in the “Hardware and Sound” category. Right-click on the name of the printer you want and select “Set as default”.

canon, printer, does, print

What to do if the HP LaserJet p1005 printer does not print?

Like any printer, the HP LaserJet P1005 may NOT print for one of the following reasons: Damaged cable. The printer connects to the computer via a USB cable. The driver is, in fact, a regular program, and if its files are damaged, the HP LaserJet P1005 printer will NOT print.

How to remove unnecessary printers?

Delete printer in system settings

  • Open the Start menu and go to Settings.
  • Go to “Devices”, on the left side, select “Printers and scanners”, on the right side, click on the printer you want to delete, and in the menu that appears, click on “Remove device”.

How to install a driver on a Windows 10 printer?

Install manually a local printer

  • Open Settings.
  • Select Devices.
  • Select Printers & Scanners.
  • Click Add Printer or Scanner.
  • Wait.
  • Select the printer you want is listed.
  • Select Add a local or network printer.
  • Click Next.

Where to download printer drivers?

To do this, follow these steps:

  • On a 64-bit Windows computer, from the Start menu, select Settings, then Printers and Faxes.
  • Double-click the Add Printer icon.
  • Click Next and follow the instructions on the screen.

How to set up your HP Laser Jet p1102 printer?

Setting up a network device

  • Connect your wireless device to your computer using a USB cable.
  • Click the Start button, then click Programs or All Programs.
  • Click the HP menu item, then click Printer Series.
  • Click on Wireless Setup.

How to reset HP LaserJet p1102 printer?

Turn off the device. 2. Turn on the device and during initialization press and hold the [Cancel] and [Wireless] buttons for about 15 seconds (when all LEDs are blinking, release the buttons).

NNCXV.INFO 2021