Connect the printer to a Wi-Fi network

How to connect a printer via WI-FI correctly. The most common mistakes when connecting and configuring

connect, printer, wi-fi, network

If you look at modern printing devices, you will notice that for the most part they have very broad functionality. As a result, it will be much easier for an ordinary person to work with them. Connection without using wires is one of the most necessary and demanded functions today, which is used in printing devices. Wi-Fi is also popular due to the fact that work has become much more comfortable and convenient, since there is no need to use a large number of connecting wires.

Is it very convenient to work with the printer? using the capabilities of the wireless Internet. This is especially important if the work is associated with frequent business trips. At home, it is also often necessary to connect a printer via WI-FI. The most important advantage is the absence of a large number of cables that are used to connect devices to each other.

When organizing their own network, many users are faced with the fact that for comfortable work it is necessary to configure shared access to the network printer being used. The printer can be connected to any personal PC on your network.

How to connect a printer via WI-FI. General instruction

  • First you need to find a printer that will suit you. It must connect to the router.
  • Using a network cable, you need to connect the network port of the router to the printer. Next, we connect the printer to a personal PC.
  • On all computers that will be in the network, it is imperative to install all the necessary drivers for the selected printer.
  • You need to set a static IP for the device. It is best to use the addresses of the zone where other devices on the network are located. Only the fourth segments should be different in all addresses. When activated, the network printer will have an unchanged IP even if the DHCP function is enabled in the router.
  • To find the device conveniently, and also to avoid confusion, you can change the name of the printer.

Connection can be made using the built-in Print Server. With its help, the connection is made. As a result, access is opened from any personal PC that is in the network coverage area.

First, you need to connect the printer to one of the computers on the network. To do this, you need to connect it to the USB port and load all the drivers necessary for its operation. They are most often supplied with the printer on an installation disc. To check if the installation is correct, you need to run a test page. If everything is installed correctly, the next step is to set it up as a network printer.

To connect the printer via Wi-Fi, you first need to set up the print server. To do this, you need to connect the printer to the router. The built-in menu of the router is used for configuration. To get into it, you need to write in the search bar in any browser. If the IP address was changed during setup, then you must enter the changed address.

In devices, you can now see the printer and check its status. The most important setting here is Printer location. In this line, you will need to write the network address of the device on each personal PC that is connected to the network. The printer must be installed on every computer. When the setup wizard starts, you will need to note that this will be a network printer.

The printer address is indicated by the one shown on the router. If the printer model is not displayed, you need to install a local device on this computer. If everything went well, it becomes the default on every PC. To check that everything was done correctly, you can print a test page.

There is another way to connect a printer via WI-FI. This method will be ideal if the IP address of the personal PC and Windows 7 OS are in the same radius with the network printer. To work, you need to turn on Wi-Fi on the printer and find it on the computer.

The above method of how to install the printer via WI-FI may not work. Then you need to open “Network Neighborhood”, then right-click on the icon, select properties and open “Network Connections”. Next, we find the “Local network”, and here we need the “General” tab. There we find the TCP / IP protocol and in its properties we register the IP address, which we find in the instructions for this device.

There is another way how to connect the printer via Wi-Fi. To implement it on a router, you need to create access points. To do this, you need to connect the router to the printer using Wi-Fi for this. In the printer, you need to specify the type of encryption used and the access key. If the Wi-Fi indicator lights up, it means that everything was done correctly.

The most common mistakes when connecting and configuring

  • Sometimes situations may arise that everything seems to be done correctly, but the network printer via WI-FI does not print or prints incorrectly. To solve this problem, you can use this solution. All well-known manufacturers, in addition to the equipment, can offer free utilities that are engaged in troubleshooting and troubleshooting in operation. To solve the problem, such a utility will be enough to run and follow the instructions.
  • The router does not support the printer model installed on the system. In order to avoid such an error when buying, it is necessary to clarify all compatibility issues.
  • Incorrectly installed drivers.
  • Incorrect Wi-Fi configuration in the operating system itself.
  • When installing equipment, people do not always carefully read the instructions that come with the equipment and tell you how to set up the printer via WI-FI.

    It is also necessary to choose the correct location for the router. The coverage area of ​​the router must necessarily cover all those places where access is needed. With a weak signal, the router must be positioned in such a way that its network slightly extends beyond the boundaries of the apartment or office.

    Wireless pairing ideas are ubiquitous. The trend has not spared the equipment for displaying information. Therefore, it is required to solve the question of how to connect the printer to the laptop via WI-FI.

    Before connecting the printer to a computer via WI-FI in this way, you need to make sure that the printing equipment can be connected using the wizard.

    If the MFP supports WEP and WPA encryption, the pairing will be successful. It is necessary to connect the device in the following sequence:

    • In the device control menu, select “Settings”. “Network”. The wizard will display a list of nearby access points.
    • Choosing our Wi-Fi.
    • Enter the network encryption password.

    How do I connect a wireless printer to my computer if the previous methods didn’t work? There is one more way, but it differs in complexity in comparison with the previous options. In such techniques, there are always nuances that can play a role in connecting devices. Most often they relate to the factory IP address and subnet mask, which is provided by the provider.

    But such a situation is unlikely, and therefore it does not hurt to connect an MFP. This is due to the fact that most of the equipment does not use static addresses, but dynamic ones. For printing equipment of this kind, you just need to add the IP address available on the device in the computer settings. How to connect a printer to a laptop without a wire in this case? Follow the following scheme:

    • We go to the control panel.
    • We select the item “Devices and Printers”. “Printer Installation”.
    • 2 items will appear in the window that opens. Here you will need to select the “Add a network, wireless or Bluetooth printer” block.
    • The PC will start searching for suitable hardware automatically. When the MFP is found, it will appear on the screen.
    • After that, you need to open the proposed block, where you need to enter the IP that the MFP has.

    At the end of the connection procedure, a window will appear notifying you of successful pairing with the output device. You can start working with printing equipment immediately after restarting the laptop.

    READ  Apple Mail sign in to mailbox

    Full-frame mirrorless camera equipped with innovative technologies

    Unleash your creativity with our range of DSLR cameras.

    The power of DSLR cameras in a compact body.

    Find the perfect versatile camera for you.

    Control external and on-camera flashes.

    Create and share beautiful HD videos.

    Enjoy the highest image quality.

    Discover all the possibilities of filming.

    Find out more about new Canon camcorders.

    Full frame mirrorless lenses unique to the EOS R.

    Combination of superior image quality, versatility and speed.

    Lenses for excellent image quality on APS-C sensor cameras.

    Portable, lightweight lenses designed specifically for EOS M cameras.

    Devices for photo printing and home use.

    Experience our versatile and reliable printers.

    prints with less cost without sacrificing quality

    Find supplies for your Canon printer.

    Cloud storage and image management.

    Create beautiful video and photo chronicles.

    Convenient home storage for pictures and videos.

    With Image Stabilizer. for nature, travel and sports.

    Stylish and practical. mobile, desktop, scientific and printing.

    Photos, documents and large format materials for office and home.

    Red laser pointers for presentations.

    High quality printers and faxes for your business.

    Digital projectors for visual impact.

    High performance and discreet security and video surveillance cameras.

    Find consumables for your business printer.

    Admire the best moments in the image timeline.

    Shoot, send and sync using your smartphone.

    Expand the capabilities of your EOS camera.

    Download it now and take great shots.

    Print from your smartphone or tablet to PIXMA and SELPHY printers

    Tips and tricks from the print professionals.

    Check out the latest tips and techniques.

    Stay connected for easy storage and transfer of data.

    Inspirational work from amateurs and professionals.

    Photographers share their creative secrets.

    Get expert advice every week.

    Stay up to date with the latest digital innovations.

    Check out our photography tips and tricks.

    Find out about upcoming events for photographers.

    Stay up to date with all new product information

    Download software for your Canon product.

    Download the Canon product user manual.

    Look for answers to frequently asked questions.

    Learn more about Canon Professional Services, including benefits and how to become a member.

    Find answers to many of the frequently asked questions about Canon Professional Services here.

    Find contact information for your country and ask experts for help.

    Our experts will ensure the smooth operation of your equipment, improve its performance or repair it.

    Find Drivers, Manuals, Firmware and Software.

    Find instructions on how to set up a wireless connection on your PIXMA MG3540 printer and how to reset the printer to factory settings.

    Some access points (sometimes also called routers or hubs) have an auto connect button labeled “WPS,” an abbreviation for Wi-Fi Protected Setup.

    It allows related devices, such as the PIXMA MG3540, to connect to the network without the need for a password, and provides a quick and easy way to connect devices.

    This is the most convenient way to connect your PIXMA MG3540, so if your access point has a WPS button please select the WPS Connection Method tab below for instructions on how to connect using that method.

    If your router does not support WPS, refer to the alternative instructions for connecting your PIXMA MG3540 by selecting the Standard Connection Method tab below

    Before you start, there are a few conditions you must meet to use the WPS push button method:

    • The access point must have a physical WPS button. For more information, refer to the user manual for your device. If there is no WPS button, follow the instructions on the Standard Connection Method tab.
    • The network must use WPA (Wi-Fi Protected Access) or WPA2 encryption. Most access points with WPS support use this protocol.

    Press and hold the [Wi-Fi] button on the top of the printer until the orange alarm indicator blinks once.

    Make sure that the indicator next to the button starts flashing blue, then on the access point press and hold the [WPS] button for 2 minutes.

    For exact information on how to run WPS on an access point, refer to the access point’s user manual.

    The Wi-Fi light (blue) located on the printer will continue to flash while searching, and the Power and Wi-Fi light will flash when connected to an access point.

    After the printer establishes a wireless network connection, the Power and Wi-Fi light stops blinking and stays on without blinking.

    To confirm that the printer is successfully connected to the wireless network, you can print the network settings for your printer:

    Load a sheet of A4 or Letter size plain paper.

    Press and hold the [Resume / Cancel] button until the indicator flashes 15 times, then release the button.
    The network information page prints.

    When using the data from the printout, make sure “Connection” is displayed as “Active” and that the SSID (wireless network name) contains the correct name of your wireless network.

    This completes the WPS setup procedure.

    Please now proceed by installing the software to make the most out of your PIXMA MG3540.

    If you do not have an installation CD with your product, you can download manuals and software by selecting your product on the PIXMA product line page.

    If you cannot complete the WPS wireless setup following these instructions, please contact us for further instructions.

    For Windows users: insert the supplied CD and run the installer.

    If the installation CD that came with the product is not available, or if you are a Mac user, manuals and software can be downloaded by selecting the product on the PIXMA product line page.

    After the initial screen is displayed, click [Next].

    When the following screen is displayed, enter your password to enable installation of the Assistant Tool, then click [Installation Assistant]

    After the following screen appears, click [Next].

    Note: When a screen appears asking you to choose between USB and Wireless, select [Wireless].

    Make sure the printer is on, the light is on, and then click [Next].

    Click [Connect to Network].

    When the following screen appears, click [Wireless Installation].

    Please note: Wireless installation method is not supported for Windows XP users. Select [Custom Installation], then go to step 5.

    When the [Connecting via Wireless Setup] screen appears, hold down the [Wi-Fi] button (A) on the printer until the orange alarm indicator (B) flashes 2 times, then release after the second flash.

    Check that the Wi-Fi indicator (A, blue) is blinking rapidly and the power indicator (green) is on. Click [Next].

    Please note: your network connection will be disconnected during installation.

    Windows XP users only: Select [Wireless Setup with USB Cable]

    After the following screen appears, select your region and click [Next].

    After the following screen is displayed, select the region of residence and click [Next].

    After the following screen appears, select the software you want to install and click [Next]. If you are not sure what software you want to install at this stage, do not worry. it can always be uninstalled at a later stage.

    After the following screen appears, click [Yes] to accept the terms of the license agreement.

    After the following screen appears, click [Next].

    The next screen shows the printer model and the name (or SSID) of the wireless network.

    Windows (excluding Windows XP users)

    This concludes the wireless setup for Windows.

    Windows XP users, or users of systems where the printer cannot be found, need to proceed with the USB installation detailed in step 6.

    When the following screen appears, click [Add Printer]

    On the next screen, select the [Canon IJ Network] version of the network driver and click [Add].

    Click [Next] to complete the installation.

    This concludes the wireless setup for Mac.

    Users of systems where the printer cannot be found will need to proceed with the USB installation detailed in step 6.

    Configuring with a USB cable for Windows XP users and users on systems where no network connection is detected

    Select [Set up a network connection with USB cable], then click [Next].

    After the following screen appears, connect the printer to your computer using the supplied USB cable. This cable has a symbol on the connector.

    For Mac Users: Click [Next].

    After the printer is detected, the following screen appears.

    The name of the access point to which the computer is connected will be displayed (in place of “xxxxxxxxxxxxx”).

    If you want to connect the printer to a wireless network, click [Yes].

    When the following screen is displayed, click [Allow].

    After the following screen appears, disconnect the printer from your computer and click [Next].

    When the following screen appears, click [Finish].

    This completes the setup for Windows.

    Once the printer is found, the following screen appears, displaying the name of the access point to which the computer is connected (in place of “xxxxxxxxxxxxx”). Click [OK].

    After the following screen appears, click [Add Printer].

    On the next screen, select the [Canon IJ Network] driver version and click [Add].

    Click [Next] to complete the installation.

    This completes the setup for Mac.

    If you cannot complete wireless setup following these instructions, please contact us for instructions on how to proceed.

    How to connect a regular printer to a laptop via WI-FI?

    Unfortunately, developers of budget models rarely provide devices with a built-in WI-FI transmitter, therefore, for ordinary printers, the following methods of remote connection to a computer are used:

    READ  Printer Writes Paper Jam What To Do

    Installation of additional network equipment. a print server, with which you can make the printer a node of a wireless LAN;

    Cable connection of the printer to a computer that has access to a local Wi-Fi network: thus, any WI-FI device can communicate with the printer through an “intermediary”.

    The advantage of this method lies in its cost-effectiveness: you do not have to spend money on additional expensive equipment. However, one cannot do without a second computer, which must constantly work throughout the entire “communication session”.

    To set up a printer connection via WI-FI in this way, you need to:

    Now, by the “Print” command, your laptop will automatically print to a Wi-Fi-connected printer.

    Using a WI-FI router with a built-in Print Server function and a USB connector on the case for external network devices. To set up such a connection, you should:

    However, such difficulties are justified only when Wi-Fi setup is required on a good old printer, which has long been “taken root” and is almost native. In other cases, it is more logical to immediately purchase a modern WI-FI printer with a built-in network module and not have to worry about setting up all kinds of additional equipment.

    Among the most popular time-tested vendors are: HP, Canon, Epson, Konica, Panasonic, Samsung, Xerox, Brother and Minolta: such a printer can be easily connected to a laptop, router, tablet, etc.

    At the same time, depending on the specific situation, you can create a wireless connection with a laptop in different ways: we will consider the main options for connecting a printer via WI-FI in more detail.

    Connecting the printer via WI-FI router:

    To do this, first enable the function WPS on your router, and then use the WPS (QSS) button to connect your printer to your home WI-FI network.

    To print via Wi-Fi, it is enough to connect from your laptop to the installed printer via the local network (see the link at the end of the article).

    To do this, run the “Search for available networks” in the printer control panel and select the network of your router by SSID. Here you will need to specify the password for Wi-Fi and confirm the connection to the network, after which the corresponding WI-FI indicator should light up on the printer.

    Run the driver installation and select a WI-FI connection with manual configuration of the parameters, after which the printer will be available for a wireless LAN connection.

    Canon printers are affordable, easy to use, and good value for money. Models of this brand have positively established themselves in the market. If installation via a cable usually does not cause problems, then setting up the printer in Wi-fi mode can be difficult. Let’s consider how to connect a Canon printer via Wi-fi to a computer or laptop, using the example of the common flagships Canon Pixma G3400, Canon Pixma MG3640.

    The line of Pixma printers, in particular the G3400 model, is equipped with a Wi-fi adapter that implements the connection of a Canon Pixma printer in the following modes:

    • infrastructure, that is, to a home network using a router;
    • direct connection in hotspot mode.

    The main problem in this case is switching between modes. The Pixma G3400 does not have a display, so all manipulations are performed blindly by pressing and holding the buttons on the printer body.

    The manufacturer recommends connecting a Canon printer to a computer in the access point mode, determining this method as the easiest. Follow these steps:

    • Connect the printer to the mains.
    • Press and hold the Wi-fi button until the printer power light starts blinking.
    • Press the black, color and Wi-fi buttons in sequence. The power indicator will stop blinking and will be illuminated continuously.
    • Activate Wi-fi on a computer or laptop.
    • Find your printer model in the list of displayed equipment.
    • Enter the requested password. As a password for new printers, a serial number is entered, which can be viewed directly on the printer.

    If there were no failures during the execution of the aLGorithm, then the connection was successful, and you can start working. To connect a Canon printer to a laptop, you need to do exactly the same steps.

    Some differences arise when setting up Wi-fi over a home network using a router. In this case, the Pixma printer must be switched to infrastructure mode.

    • Press and hold the Wi-fi button until the printer power light starts blinking.
    • Sequentially press the buttons for color printing, black printing and Wi-fi. The power indicator will light up constantly.

    Similar to connecting via an access point, the searched printer is defined in the hardware folder and set as the default printing device. To avoid confusion, when which buttons to press, it is worth writing down this information and sticking it directly on the printer so that it is always at hand.

    Connecting using Wi-fi Protected Setup

    Pixma printers support router connection using WPS. This method avoids entering passwords and simplifies the hardware installation procedure. In our case, the method is recommended for the Canon MG3640 printer. To use WPS, check the router settings before setting up the printer and activate WPS if necessary. The router must be equipped with a WPS button.

    The aLGorithm for connecting the printer is as follows:

    • Connect the printer to the mains.
    • Press and hold the Wi-fi button until the printer power light starts blinking.
    • Press and hold the WPS button on the router.
    • When the printer and router are connected, the light on the printer will be on continuously.

    The procedure for finding a printer by the router takes a few minutes, but in the future it will ensure uninterrupted access of the MFP to your network.

    Users still use fairly old printer models. These models do not have Wi-fi connectivity. In addition, the manufacturer does not release driver updates. For this reason, users are forced to replace a perfectly working but outdated printer with a new, upgraded model. How do I find a solution? As an example, let’s try to connect the Canon LBP 1120 printer to the Windows 7 operating system on a computer or laptop.

    The manufacturer’s website officially states that drivers for a 64-bit system are in development. If the user has a 32-bit OS, then there should be no problems installing the driver. You can check the system capacity in the Computer menu. Properties. System type (the Bit depth field). The driver for the LBP 1120 model is downloaded from the official website and installed on a computer or laptop.

    Then the printer is connected as standard:

    • Disconnect the computer (laptop) and the printer from the power supply. Connect the printer to the computer via the USB port.
    • Turn on the printer, then the computer (laptop). After loading the operating system, the search for new equipment will begin.
    • Search for and install the driver. To do this, cancel the search for the driver on the Internet and specify the system folder (the option “Search for a driver on this computer”), where the driver was saved after downloading.
    • After installing the driver, the printer is ready to work.

    And what to do if the 64-bit operating system Windows 7 is installed on the computer (laptop)?

    The problem has two options:

    • Connect the printer to another computer or laptop that has the necessary drivers, and print the necessary documents and photos via the local network;
    • Pair a virtual machine with the LBP 1120 printer driver for Windows XP.

    Virtual machines are familiar to many advanced users. These are emulator programs that reproduce the work of different platforms without reinstalling the working operating system. Examples of such machines are programs VirtualBox, Windows XP Mode.

    Briefly, the aLGorithm is as follows:

    • Download and install a virtual machine on a computer.
    • Find and save the Canon LBP 1120 driver for Windows XP to your computer.
    • Start the virtual system, install the printer in it.

    Setting up and working with virtual machines requires a fairly high level of competence. If the user is not confident in their abilities, entrust the connection of the Canon LBP1120 printer to a professional.

    Connecting a network printer in Windows 7

    How to connect a printer via WI-FI if Windows version 7 is used? Installation can be greatly simplified. To do this, only for the seventh version, you can use a special utility. She will be able to automate the entire installation process.

    At the beginning of the installation, you need to make sure that the network printer model supports the router.

    After connecting, as in the case described above, we write the following in the address bar of our browser: Add a printer. Now you need to select a port for it. Go to the “Create port” section and select “Standart TCP / IP Ports”. The next step, the installation wizard will tell you that you need to register an IP address. This address for the router and printer must be the same. Now you need to select the usual type of device and continue further connecting the printer via a WI-FI router.

    You need to install all the drivers required for the printer. Find the required model in the proposed list. After completing all these steps, the installation wizard will offer to proceed to setting up the sharing of the device.

    READ  Printer Sends To Print But Does Not Print

    The installation wizard will inform you about the correct installation of the drivers and offer to use the default printer. Click on the “Finish” button, and now it remains to configure the port properties.

    We click on the installed printer with the right mouse button, and in its properties, in the TCP port settings, select the LPR protocol and give it a name.

    When connecting, many users overlook some of the details of the settings, as a result of which not everything works as it should.

    How to connect a WI-FI printer to a computer and laptop?

    Of the “classic” ways to connect a WI-FI printer, you can note:

    How to connect via Wi-Fi HP Laserjet Pro MFP m125rnw

    The HP Laserjet Pro MFP m125rnw is multifunctional. It is able to work not only as a printing device, but also as a scanner and copier, as well as perform fax functions. Connection to Wi-Fi is carried out in the same way as other models of this company. However, this product can also print HP Wireless Direct.

    • for Apple devices using Apple iPrint or HP ePrint;
    • for Android or Symbian operating system via HP ePrint HomeBiz4
    • for computers with any operating system.

    To set up HP Wireless Direct Printing, follow these steps in sequence:

    • Press OK on the LCD panel to enter the menu.
    • “Network Setup”, “Wireless Connection Menu”, “Wireless Direct” open in sequence.
    • In the last menu, ON is pressed and then OK.

    Set up an HP Wi-Fi connection to a computer and laptop on Windows and macOS

    Most often, MacOS uses AirPrint or automatic driver download to connect a printing device. You should not install standard software on this operating system, which can be purchased with the printer or downloaded from the official Hewlet Packard website. This operating system itself will prompt, if necessary, which programs should be installed.

    To add a printing device, use the Printers and Scanners folder, which is similar to the Print Control Panel when using Windows.

    If the printer supports AirPrint, then it is, accordingly, compatible with MacOS. If not, you can find out about its possible work with this system by contacting Apple Support.

    The procedure for connecting some models of HP printing devices in the Windows system will be discussed below.

    How to connect to Wi-Fi HP Deskjet 2620

    When connecting an inkjet printer through a router, remember that it can only support one frequency. 2.4 GHz.

    On a note! By holding down the Information button for three seconds, you can print the Wireless Guide.

    This model allows you to connect using WPS. To do this, you need to press the “Wireless connection” button for more than 3 seconds. This will start Wi-Fi Protected Setup and its indicator will blink. After that, the WPS button on the router is pressed. It takes about 2 minutes to connect, if successful, the blue light will just be on.

    If the router does not support the one-button connection function, it should be done using a pin code. It can be printed by holding down the “Information” and “Wireless connection” buttons at the same time.

    Next, hold down the “Wireless connection” until the indicator blinks, enter the PIN code in the configuration program for the access point or router. The process will be completed in two minutes.

    Also, this model allows you to connect using the Wi-Fi Direct function, which makes it possible to connect to the device directly.

    How to connect an HP printer to Wi-Fi

    The idea to make life easier for users and remove “hated” wires appeared about 5 years ago.

    The user should be aware that each specific model has its own key settings and software capabilities. Only after a thorough study of the instructions can you start connecting the device.

    Unfortunately, there is no universal order of actions, the implementation of which will make it possible to simplify the task as much as possible. But the general aLGorithm of actions, of course, is similar and the final result depends on it.

    Before you can connect your HP printer to Wi-Fi, you need to take it out of the box, that is, unpack it. The next step is to carefully study the instructions for removing all packaging.

    Then you need to connect the cable by plugging the device into an outlet. When the printer is turned on, the cartridges are installed. The technician will carry out all the initial settings and print a test page.

    On a note! This function is not applicable for some models.

    Before printing via Wi-Fi to a printer, you should decide on the connection method that is most appropriate in a particular case.

    One of the following wireless connection methods is most commonly used.

    It is important to understand that the principle of operation of wireless devices is being improved every second. Each manufacturing company is trying to implement something of its own and get ahead of the competition.

    • Sockets with connected electricity.
    • A device that allows you to connect via Wi-Fi. This device is called a router and looks like a rectangular box with one or two antennas. Depending on the modification, it can have a socket or cable connection.
    • Directly the printer itself, which must support wireless communication. The presence of such a function at the time of sale must be reported by the sales consultant.
    • Any gadget that is initially connected to a local network. Better to use a laptop or desktop computer. This point is very important, this is how you can check the correctness of the work performed in the end result.
    • Drivers. They can be downloaded from the Internet or taken on a disk that should be in the box with the printer.

    Attention! Some computer manufacturers use AirPrint, as this program allows you to automatically connect any equipment.

    HP Laserjet 1536dnf MFP. Wi-Fi Connection

    Connecting this laser MFP to Wi-Fi starts with setting the IP address. It can be manual, but automatic is mainly used. To do this, you need to press the “Settings” button, then select “Network installation” with the arrows and press OK. then select “TCP / IP Settings”, OK, Automatic, OK. The process may take some time.

    The software is installed from the CD according to the prompts that appear on the screen. After the machine asks for a wired network connection, select “Next” and select the printer with the desired IP address. Printer installed.

    HP Deskjet 2630. Wi-Fi Setup

    Before connecting to a wireless network, you must first install the printer software.

    After turning on the computer and router, you should make sure that you are connected to the Internet.

    As with other HP models, it is important that both devices operate from the same network.

    The next step is to disconnect all cables from the printer. To facilitate the work of setting up Wi-Fi, on the manufacturer’s website, you need to open and then launch HP Easy Start. In the Windows that open, you need to select a wireless network and then proceed to complete all settings.

    Advice! All installation and configuration work is recommended to be performed at high Internet speeds.

    HP 107w Wi-Fi setup

    It should be understood that the wireless network configuration can be carried out not only on the computer, but also on the printing device itself.

    First you need to check which “Windows” is on your computer. 7 or later is suitable for wireless connection.

    You can download software for this printer model from the HP website. You also need to take care of the availability of a device with an interface suitable for this task in advance.

    The step-by-step activities are as follows:

    • All three devices turn on.
    • The drivers required for the operation are loaded and installed.
    • Performs step-by-step actions as indicated on the computer screen.

    Important! It is necessary to select the wireless network during installation.

    After passing through all the Windows, the “Finish” icon will inform you about the completion of the installation.

    HP 107w

    HP Laserjet Pro MFP m28w Wi-Fi connectivity

    This device can be connected not only wirelessly, but also directly via USB. Supports most of the available protocols seamlessly and runs virtually seamlessly.

    In addition to the elementary connection, which is thoroughly described in the instructions, for this HP m28w MFP, Wi-Fi setup is very simple, it can be “customized” for a specific user. Even a novice computer scientist can cope with this task.

    Another pleasant “extra” is the ability to work together with this giant smartphone. The existing application, which, by the way, is configured automatically, can do:

    • Photos and documents even from the phone’s internal memory.
    • Seamlessly print anything from the connected cloud.
    • Scanning can be done not only with MFPs, but also with a gadget camera.

    Important. The device belongs to the so-called latest generation technology, and even a child is able to deal with it.

    NNCXV.INFO 2021