DIY stylus for ipad

How to make a stylus with your own hands

Probably, many smartphone owners are interested in how to make a stylus with their own hands. This is due to the fact that such details are being increasingly introduced into many devices again. Usually these unique products come with tablets or phones, but if you lose them, you will have to buy new mini-pens, and they cost a lot of money.

The easiest way to create a stylus

How to make a stylus for a tablet with your own hands? This process is very simple and economical, since everyone has the necessary materials on the farm. Thanks to the creation of such a detail, it will become much more convenient to work with a smartphone. For the device to function effectively, it must be designed so that it can serve as a conductor of static charge between the fingers and the display of the equipment. Before making a stylus for a smartphone, you need to prepare:

  • thick aluminum foil;
  • cotton swab;
  • pen (ballpoint);
  • Scotch;
  • scissors.

How to make a stylus on your own? To do this, you need to open the ballpoint pen and remove the rod from there. Then you need to take a cotton swab and cut it at an acute angle. After this process, you need to apply the resulting element to replace the rod. You need to fix the stick using scotch tape. At the end of this stage, you should take the foil, wrap the handle with it a little higher than the cotton swab is located. It is recommended to wrap it tightly, after which you need to fix the upper part of the handle with tape. Next, you need to moisten a cotton swab. After that, you can already start working. It is very important that your fingers touch the foil. This will allow static electricity to flow through and interact with the screen. But such a homemade stylus has a small drawback: it requires periodic wetting of the cotton tip. Therefore, before creating it, you need to think about your convenience.

Stylus for capacitive touch screen with your own hand

You can make a stylus for a capacitive screen with your own hands. To make it thin and easy to use, you must apply:

If the inventory list is at hand, and it is completely satisfied, then you can proceed directly to creating a stylus. To do this, it is necessary to solder the handle / shaft to the washer at an angle so that it becomes as compatible as possible with the natural position of the human limb. But this design can scratch the display, and the thinner it is, the worse. You can eliminate this defect with the help of threads. To do this, it is necessary to wrap them around the ring-shaped edge of the device. To increase the contact, you need to bring your finger close to the smartphone. Such a device does not leave any scratches on the capacitive surface, and the thin screen responds very quickly, so there is no need to press on the device. Also, if you make a stylus for a smartphone or tablet with your own hands according to this scheme, then you can not worry about the appearance of marks and scratches on the screen. It’s easy to use and can even wipe the display to keep it clean at all times.

If you know how to make a stylus for your phone, you don’t have to spend money on buying such a device.

Homemade stylus for iPad

By inventing the legendary iPhone, released back in 2007, Steve Job made a real revolution. controlling the phone became possible with your fingers! But why not use your usual stylus? The answer is simple: you take it out, then you take it away, then you take it out again, and, in the end, you lose it. Nevertheless, for some programs, primarily for drawing, this accessory is required. In this regard, we will consider the question of how to make a stylus for the iPad with your own hands and from handy materials.

What is a stylus for??

A stylus is a small, bunched or pen-shaped writing wand that can be controlled by a computer graphics tablet or touch-sensitive devices. Today, a huge variety of these accessories are made, but you can make a stylus for iPad with your own hands.

  • The accessory is very convenient when writing on the screen, because it is not very convenient to display symbols with your fingers
  • To work with graphic editors, tables or diagrams, a stylus is a must, since small elements require high precision. This is why the stylus is the best tool for designers and artists.
  • Using a stylus will make your screen less dirty
  • If you think about hygiene, the stylus is much less likely to carry bacteria than dozens of hands touching the screen.
  • Game lovers will find it much more convenient to use a stylus rather than fingers
  • And, of course, for girls who wear long nails that prevent their fingertips from touching the screen, a stylus is the best solution.

Making a stylus. the way

The first method is the fastest and simplest, but the present invention will be disposable. The fact is that the salt water used in its construction will dry out quickly. Such an accessory will be quite enough for several hours, but after that it will need to be moistened in water.

READ  How to transfer photos from ipad to computer

To create such a device, you will need:

  • Empty pen
  • Insulating tape
  • Scissors / threads
  • Sanitary stick / cotton wool
  • Foil
  • Salt
  • Water

This method is clearly shown in this

First, roll the foil into a tube and place the handle in the empty cavity so that the foil takes up all the space in it, sticking out a little. Then wrap the protruding piece of foil with a veil, securing it with thread, or insert half of the sanitary stick into the handle so that the soft tip sticks out.

stylus, ipad

Then, wrap foil over the entire handle and secure the material with duct tape. All parts of the accessory must be in close contact with each other.

In order for the device to work, you need to place the tip of the homemade stylus in salt water for a few seconds. We need salt water to conduct energy. Your stylus is now ready!

Making a stylus. the way

The second method will help you create a more durable stylus.

To invent it, you will need:

  • A pen
  • Pliers
  • Protected wire
  • A piece of polyethylene foam

First, remove the rod and all other parts from the handle, leaving only the tube. Cut off a piece of polyethylene foam so that it can fit in the handle, but still grip tightly. Cut a piece of shielded wire so long that it is 2-2.5 times longer than the handle. Free the part of the wire that extends beyond the length of the handle from the protective rubber (in simple words “strip” the wire).

How to make a DIY Touch Pen in 2 Minutes. AWESOME

Wrap the bare wire around half a piece of polyethylene foam. Insert the structure into the handle so that the free part of the polyethylene foam sticks out of the handle by a centimeter.

Now, in your stylus, one side of the pen is covered with polyethylene foam, and the other end of the wire sticks out from the other. Separate the protective rubber from the protruding end and coil the wire around the handle. Secure it with duct tape. Now smooth the end of your stylus a little, and it’s ready.!

If you like, you can make the stylus tip of any size. Thus, you will have the perfect tool for controlling iPad, and especially for drawing.

Our service offers the purchase of computer, digital and video equipment from Apple on the most favorable terms

Get professional advice from a licensed Apple technician now

All rights reserved, for any copying of the material, a link to the site ¶¶¶ is required. Aggle Service Center is a post-warranty (unauthorized) service center. The information presented on the site is not a public offer.

  • iPhone
  • iPad
  • MacBook
  • iMac
  • Watch

Moscow, avenue Vernadsky, 39, office 425 in the business center “Vernadsky”

Apple products, trademarks and registered marks are the property of Apple Inc.

DIY iPad stylus

Doing something with your own hands has always been highly appreciated.

Especially when it comes to modern devices and accessories for them. Probably every happy owner of an iPad at least once tried to adapt some thing as a stand for his tablet.

With the release of numerous drawing and design programs on the iPad, there is an urgent need for a stylus. If for some reason it doesn’t suit you, you don’t like it, or you just can’t get a ready-made stylus. Try DIY iPad stylus. There are several ways to make your own iPad stylus. This article describes two of them. 1 way how to make a stylus for iPad with your own hands: A very simple way. However, the stylus obtained in this way will be disposable. It will be enough for just a few hours. Then you will need to moisten. To create a stylus, you will need:. an empty ballpoint pen. scissors. electrical tape (you can use threads). a hygienic stick (a small piece of rag). foil. water. salt First you need to twist the foil with a tube and insert it into an empty pen so that it fills everything in the pen space and looked out a little. Next, wrap the foil with a piece of rag or cut the stick into 2 parts and insert into the foil. In this case, the cotton head should be in contact with the foil. After that, wrap the handle itself tightly with foil. All elements must be in close contact with each other. For beauty, you can wrap the pen with duct tape or thread. Those who are fond of knitting will be able to make an original case for their stylus.

Your stylus only needs water to work. Dip the handpiece in salted water before use. This is necessary for conductivity. After that, your stylus is ready! 2 Method of making a stylus for iPad yourself: This method will help you make a stronger and more durable stylus. To do this, you will need:. an empty ballpoint pen. pliers. shielded wire. polyethylene foam (used as a lining for radio components). The first step is to cut the polyethylene foam so that the desired part is about the thickness of a ballpoint pen. Next, you need to peel off the insulation from the tip of the wire, stick it into the polyethylene foam and twist it around it. Then carefully thread the wire through the handle. Leave the tip with the polyethylene foam a few millimeters out.

Bare the rest of the wire and wrap it around the outside of the handle. Glue the tip with electrical tape. For beauty and convenience, at the end, you need to trim the protruding end of the polyethylene foam, making it round. Check it out. you get a great stylus!

A stylus for a capacitive screen: why it is and how to make it

Nowadays, capacitive touch screens are replacing resistive screens more and more actively. This type has obvious advantages: this type of sensor is more robust and durable due to the fact that the flexible resistive membrane in it is replaced by a grid of electrodes. The capacitive screen supports more touches than its sibling, it is more transparent, and only for it the multitouch technology is now implemented, which is popular today.

READ  How to determine which iPad I have

The difficulty lies in the fact that using your fingers to work with the interface is not always convenient, and in this case there are no other options. This is quite noticeable when drawing or entering handwritten text on the tablet screen, as well as in winter, when you don’t want to take off your gloves on the street at all, but you need to make certain manipulations. At such moments, a stylus for a capacitive screen would be useful to many. Many may remember the convenience of using such a manipulator if they once owned smartphones with resistive screens. It allows for more precise manipulations. But the capacitive screen does not respond to the touch of a conventional stylus, since it requires a certain capacitance to work with it, which accepts and conducts an electric current with a low voltage. Mobile phone manufacturers are also ready to offer a stylus for a capacitive screen. It can be different in appearance, but it is made from special conductive materials. The stylus for a capacitive screen has a fairly simple device that allows you to make it yourself.

stylus, ipad

The mobile gadgets market offers four types of stylus models:

The stylus model SPMP 1019, designed for iPhone, iPad, HTC and Samsung screens, belongs to the second category. This model is considered inexpensive, and high quality is ensured through the use of a metal case. The presence of a hook, similar to that on a ballpoint pen, allows you to conveniently fix it. Its disadvantage is fragility. This gadget will not lose its tactile properties at low temperatures. At the moment, the most convenient stylus for a capacitive screen is made of conductive rubber. It has design features that provide a seamless touch of the screen with your fingers. The tactile response of such devices is considered to be the highest. The degree of depression is easily adjustable.

DIY capacitive stylus

From what was written earlier, it should be clear to you that the market is ready to provide a huge variety of options for this device. However, the question of how to make a stylus for a capacitive screen can be of concern to many. Here you can recommend the following set of tools: embossed pushpin, nail file, metal pen, tin, soldering iron, glue, copper wire, self-adhesive, battery. The wire should be soldered to the button, after which the workpiece should be pushed into the handle body, and glued at the end. Stick the self-adhesive on the button, and cut off the remains. The other end of the wire should be fixed to the battery, close the handle body. Capacitive stylus ready!

DIY stylus for thermal and capacitive screen

The market of modern gadgets decided to remind us again of the already forgotten stylus.

How To Make A Stylus Using Any Pen/Pencil

stylus, ipad

Branded “sticks” were recently presented by Apple; Samsung launches S-Pen line for its Galaxy Note product.

Such a device is also convenient for those who like to draw on the screen of their smartphone or tablet. It is quite possible to make a stylus with your own hands quickly and without the use of expensive materials.

DIY stylus

How to make an electronic pen (stylus) and a mini tablet with your own hands?

How to make a mini tablet and a stylus for a laptop out of all the trash.

That is, we are talking about an electronic pen with which you can write handwritten texts or draw.

To understand why the touchpad cannot be used with any object, such as a pencil, you need to figure out how it works.

The touchpad is a touch panel that works on a capacitive principle. Capacitive sensors are located inside the panel, which react to changes in capacitance introduced by a person’s finger. To reduce recognition errors of this very finger, the touch panel also reacts to the capacity of the human body, which it registers through the finger touching the panel.

How to Make an iPad Stylus Pen Easy Tutorial | Toy Caboodle

In general, the task was to trick the touchpad and slip it with a regular plastic handle instead of a finger. As it turned out, this is easy to do. It is enough to choose a metal washer of a suitable size and attach a small piece of wire to it. The wire can be passed into any hollow tube, for example, a body from a felt-tip pen or a ballpoint pen.

The initial project was very simple. I installed the button inside the body from the felt-tip pen and propped it up from the inside with a piece of thick cardboard so that the cardboard was firmly stuck between the button and the body.

I assumed that it would be possible to write characters by pressing this button each time. But, even after the first test of the pen, it became clear that writing and pressing this button at the beginning of each element of the letter is extremely inconvenient. After all, we are already used to the fact that the line begins when the pen is pressed against the paper or tablet.

So, the nib had to be slightly modernized by adding a stylus pressure sensor to it. In the drawing, the final version of the nib.

  • Tube (cambric).
  • Tailor’s pin.
  • Silicone part of the assembly from the keyboard.
  • Brass plate.
  • Double sided tape.
  • PTFE film.

This drawing is to explain how the electronic pen nibbler works.

One element of the nib is a silicone pimple, which is used in computer keyboards, remote controls, etc. This assembly unit required minimal rework. I just removed the contact pad made of harder rubber from its inner surface.

READ  How to connect a gamepad to ipad

This dome-shaped rubber band holds the brass plate and allows you to tilt the pen while keeping the plate horizontal relative to the touchpad surface.

An ordinary tailor pin passes through the middle of this elastic band, which, together with the brass plate, is a contact pair. The latter, when you click on the writing node, closes the left mouse button.

To ensure good glide of the pen on the surface of the touch panel, a fluoroplastic (Teflon) film is glued to the brass plate using double-sided tape.

Additional ways

You can make a stylus for a capacitive screen with your own hands in a slightly different way. For example:

  • Take an aluminum tube, attach a piece of anti-static sponge to one of its ends, which can be found in chip boxes.
  • You can build a stylus with your own hands from the same pen without a rod, replacing the cotton wool with paper, and the foil with metal packaging for chocolate, coffee, tea, etc.
  • Some users prefer to use a thin battery as a stylus, bringing its negative pole to the screen.
  • You can use one anti-static film rolled into a tube, securing its shape with pieces of tape.
  • A lightweight aluminum stick that does not scratch the screen is also a good stylus. Only its head should not be too small, otherwise the screen simply will not “see” this object.
  • Making a stylus. the way

    The second method will help you create a more durable stylus.

    To invent it, you will need:

    • A pen
    • Pliers
    • Protected wire
    • A piece of polyethylene foam

    First, remove the rod and all other parts from the handle, leaving only the tube. Cut off a piece of polyethylene foam so that it can fit in the handle, but at the same time hold tightly in it.

    Cut a piece of shielded wire so long that it is 2-2.5 times longer than the handle.

    Free the part of the wire that extends beyond the length of the handle from the protective rubber (in simple words “strip” the wire).

    Wrap the bare wire around half a piece of polyethylene foam. Insert the structure into the handle so that the free part of the polyethylene foam sticks out of the handle by a centimeter.

    Now, in your stylus, one side of the pen is covered with polyethylene foam, and the other end of the wire sticks out from the other. Separate the protective rubber from the protruding end and coil the wire around the handle. Secure it with duct tape. Now smooth the end of your stylus a little, and it’s ready.!

    If you like, you can make the stylus tip of any size. Thus, you will have the perfect tool for controlling iPad, and especially for drawing.

    Homemade stylus for iPad

    By inventing the legendary iPhone, released back in 2007, Steve Job made a real revolution. controlling the phone became possible with your fingers! But why not use your usual stylus? The answer is simple: you take it out, then you take it away, then you take it out again, and, in the end, you lose it. Nevertheless, for some programs, primarily for drawing, this accessory is required. In this regard, we will consider the question of how to make a stylus for the iPad with your own hands and from handy materials.

    Final finishing

    To prevent the sharp tip of the stylus from scratching the touchscreen of your gadgets, it must be rounded. To do this, it is enough to melt the sharp edges of the thimble in the flame of a burner or even an ordinary lighter.

    We melt the sharp tip of the “feather” so as not to scratch

    The stylus is ready, you can work

    We now have a simple thimble stylus that you can already use. Let’s move on to the next step. turn it into a work of art in the style of “Steampunk”.

    Resistive, capacitive and heat shield

    If you are eager to make your own stylus, then first of all find out the type of touch screen of your device. this will directly affect the materials for your craft:

    • Resistive screen. This type responds to absolutely any touch. with a finger, a sushi stick, a pencil, etc. Choose what you like best and your stylus is ready!
    • Capacitive screen. This touchscreen only reacts to the touch of conductive objects. A person also refers to them to some extent. our fingers, like ourselves, conduct current. This quality is possessed by all organic substances and creatures, as well as most metals.
    • Heat shield. As the name implies, the display will only respond to the touch of an object that emits heat. That is why it is difficult for us to work with such screens in the conditions of Russian frosts.

    Homemade styluses

    The rather unusual design of the capacitive stylus is a ring of conductive material, about 1 cm in diameter, attached to a pen made of the same material. Such a construction is described here. It seemed to the author that such a stylus could be made much easier by folding a suitable piece of single-core wire in the required shape.

    The part of the wire that the user holds with his fingers is stripped of insulation. In general, the design is efficient, although sometimes the screen misses the operation.

    The idea arose to further simplify the construction of a homemade “stylus” simply to strip one end of the wire by 4-5 cm, and roll the other insulated end, about the same length, into a spiral. But this design turned out to be not very efficient, the screen regularly skips commands.

    NNCXV.INFO 2021