Epson printer prints with stripes what to do

Pumping ink

  • Switch on the equipment and open the cover.
  • Disconnect the power supply and unplug the cord (otherwise the carriage will not move freely on the rails).
  • Unscrew the carriage latch.
  • Move the cover to the side and remove it.
  • Using a screwdriver, tighten the latches and release the damper chambers.
  • Remove cameras (or cartridges) from the carriage.
  • Insert a clean syringe (without a needle) into the cartridge inlet. It then turns at an angle and stretches until the chamber is completely filled.

It is recommended to stock up on napkins, as ink can stain the work surface.

The pumped-over cartridge is immediately inserted into the equipment. Next, all empty chambers are filled and a software head cleaning is performed. The printer needs to stand for about half an hour before use.

Instructions for eliminating printing stripes on the Epson L210 printer

Printing equipment is an essential item in the office or at home, as it helps to solve everyday problems. However, sooner or later any equipment starts working with defects. If the problem is not resolved in time, the device may break.

epson, printer, prints, stripes

You should not immediately run to the workshop. The problem can be easily eliminated on your own. In this article, we will tell you in detail and show what to do if the Epson L210 printer prints with stripes.

Cleaning the printer head

The heads can be located in the cartridge or inside the equipment. Epson models usually use the second option. Since replacing the cartridge may be unprofitable (it is not used to the end, in Epson the part costs no less than a new printer), cleaning is recommended.

  • Insert the paper template into the printer, open the management application and go to “Service”, then to “Service”.
  • Implement head cleaning and nozzle verification.

Solving problems with the print head using proprietary utilities

The necessary options are available not only in Epson programs, but also in utilities for other printers.

Checking the ink level

  • Run the control program (install from the disk that comes in the box or download from the official website).
  • Go to “Service”, then to “Service”.
  • Run automatic level check.

In CISS systems, the parameter can be inspected externally, since the walls of the cans transmit light. If the ink is low, the cartridge should be refilled.

Problems with CISS

If the printer works with CISS, then you need to check that the holes in the system are open (not those into which paints are poured, but which allow air to pass through). If filters are installed, then they should be pulled back and tried to blow. When the air passes with difficulty, the part will have to be replaced (the equipment can temporarily work without filters). When the flow is not obstructed, it is recommended to pump the cartridges.

Technological cleaning

Allow the equipment to stand for 6 hours before cleaning. Then you need to run software processing and nozzle testing. If the check fails, then you need to start technological cleaning (open the program, go to “Service”. “Service” and click on “Technological cleaning”).

Why do such malfunctions occur?

This feature is most often found on inkjet printers (it doesn’t matter, it’s an old model with cartridges or a modern 7-color CISS). During the operation of the equipment, clear white stripes are obtained. However, it is worth mentioning that they can have a different shade.

If colored toner is used, the stripes are gradient. The printer forms shades by mixing base colors. If a specific color is not enough (little ink, problems with feeding from CISS), then a gap is formed in places. For example, purple stripes are formed on a blue background.

Most often the reason is a lack of toner. From practice, categories of reasons for the appearance of stripes can be distinguished:

  • One or a group of cartridges are low on ink;
  • With prolonged use of the cartridge, the mixture inside began to thicken (clots make it difficult to feed for printing);
  • Air has entered the printhead;
  • There are “congestions” in the air passages of ink tanks or CISS;
    The ink passage plume was squeezed;
  • Breakage of the head or loop;
  • Encoder parts (the part of the printer that guides the print positions on the blank paper sheet) are broken or dirty.

How to fix?

The problem must be resolved as soon as possible, otherwise the printer will break down completely. There are several ways to do this.

Why does my Epson printer print with stripes, how to fix the problem

If streaks appear when printing with an Epson printer, the cause of the problem is low ink levels, clogged nozzles, or a mechanical or electrical malfunction. Let’s figure out what the malfunctions are associated with and how to fix them.

Unsuitable ink

When streaks appear on the inkjet printer after refueling, the problem is with the wrong ink. A special set of inks is produced for each printer, and if an attempt is made to replace them with an available option, printing is disrupted.

Damaged cartridge

  • leaks on the body or compartment where the cartridges are installed;
  • dirt in the air intake vents, causing intermittent ink flow and print defects.

You cannot fix leaks manually, so the best solution is to replace the cartridge. If the problem is contamination, then they get rid of them by rinsing the container. Dried ink can be pushed through, temporarily eliminating horizontal streaks on documents.

Clogged cartridge nozzles

Clogged nozzles occurs for two reasons:

  • during the installation of ink tanks, small debris got into the camera;
  • dried dirt remains on the nozzles.

Disassembling the printer for cleaning is optional, instead:

  • on Windows, open “Start” and from there go to “Settings”;
  • open the “Devices” section;
  • in the menu on the left, click on “Printers and Scanners”;
  • once click on the used device in the window on the right;
  • a menu will appear where select “Control”;
  • there click on “Print Settings”;
  • go to the “Maintenance” tab, in the middle open “Cleaning the print head”;
  • After reading the brief instructions, tap “Run”.

Perform the operation 2-3 times in a row, and then leave the printer idle for an hour. Then check how the stripes are on the print.

  • remove the cartridges from the case to wipe them with a lint-free cloth;
  • if the nozzles are noticeably clogged with dirt or ink, it is recommended to soak them by immersing them in a liquid (water, special liquid) for 5-50 minutes and to a depth of 0.5 centimeters. Then clean up the dirt and try to print the document;
  • additionally clean the compartment where the cartridges are installed. Dust or small debris may have entered the area, clogging the ink passages.

Note! Using the CISS system, check the ink supply tubes, they should not be bent or pinched.

Ink and cartridge problem

The main reason why the printer prints stripes is due to insufficient ink or damage to the cartridge.

Checking the ink levels

To check the ink supply for printing:

  • install the Epson Status Monitor 3 program on your computer;
  • open a text editor or document for printing and simultaneously press Ctrl P;
  • in the “Printer” section, select the connected model, be it Epson L110 / L210 / L312, and click on the “Properties” or “Settings” button. depending on the version;
  • from there go to the “Maintence” tab and select “Epson Status Monitor 3”;
  • a window will appear with information about the ink level in the cartridge, which will look like a graphic image.

When a continuous ink supply system is connected to the printer, it is also CISS, then it is enough to determine their level by looking at the transparent containers connected to the Epson L355 / L364 / L805. If streaks appear in color printing, one of the colors has run out.

Malfunctions in the nodes of the system

In addition to the ink supply mechanism, problems arise when the electrical or mechanical components of the printer fail, after which the color or black-and-white MFP begins to print with malfunctions. It will not be possible to fix such problems without special knowledge, but you can identify the approximate cause of the malfunction.

  • As the grip of the rubber paper feed rollers decreases, the sheet feed will drop, causing the print head to cycle through the same spot multiple times. As a result, horizontal stripes appear on the document.
  • Toner leaks will occur when the absorbent pads, such as pads or absorbers, are overfilled with waste ink. It begins to flow out of the body and fall on the moving mechanisms, including the print head. On the sheets, they are like streaks or oblong stripes.
  • The streaking effect appears after a failure of the print head position sensor. The printer begins to misinterpret the location of the PG, which is why it sends false signals to it, which makes it skip areas for printing or, conversely, apply one image several times in a row.

The last malfunction can be solved by yourself. What to do for this:

  • lift the top cover of the printer;
  • check the ribbon cable to the print head. It should not be pinched or strongly bent;
  • if there is visible dirt, they should be removed.

Banding on an Epson printer is a common problem often associated with insufficient ink for printing or clogged nozzles. Less often, a malfunction arises from a mechanical or electronic failure in the operation of the device, which will require contacting specialists at the service center.

What is the cause of printer malfunction?

If the printer begins to strip after some time from the date of purchase, the matter is different. In this case, it is not at all necessary to replace it with a new one. First you need to understand the possible reasons, because often the problem is completely solvable. Streaks can appear on the paper during printing for several reasons. In this case, the reasons may depend on the type of the printer itself.

Inkjet

Inkjet printers are refilled with liquid ink. When they run out, you can notice a change in shades. For example, instead of black text, the printer prints blue text, horizontal spaces, or white stripes dividing letters into 2 parts. Sometimes the printer even prints pages with transverse stripes over the entire surface of the sheet. Such a problem indicates an overflow of the hopper or the need to replace the squeegee.

READ  How to change the default printer to another

Sometimes it is necessary to change the deformed shaft, in other cases it is enough to get rid of the foreign object that has fallen on it.

In other cases, it is necessary to inspect the integrity of the thermal film. Toner should not spill from the cartridge. It’s easy to check: you just need to take out the cartridge and shake it slightly. If this causes your hands to turn black, you will have to replace the toner with a new one. Otherwise, you will not be able to fix the problem. However, before doing anything, you need to have Honor: the ways to fix the problem are different for inkjet and laser printers.

First, you need to figure out how to fix the defect of inkjet printers on your own.

  • Checking the ink level. If your inkjet device produces stripes when printing, you must first stop printing and refill the cartridges. You cannot ignore the problem, without paint you will not be able to carry out a nozzle test. In addition, a lack of ink will cause the nozzles to burn out. To do this, find software, install and run the program. Next, open a tab with a drawing of ink capsules. It can be named by different names (“Estimated Ink Levels”, “Printer Ink Levels”). Use the printer control panel to diagnose ink levels. A visual assessment will help you understand which ink needs to be replaced. Usually, when the level is critically low, an alert icon appears in the form of a yellow triangle.
  • CISS diagnostics. If after refilling the cartridge nothing changes, stripes reappear on the paper when printing, you need to check the CISS (continuous ink supply system). It is important to make sure that the ink train is not pinched. If the system is not pinched, check the air port filters. If they are clogged, their capacity is compromised. Remove dust and dried paint. If they become unusable, you need to replace them with new ones.
  • Nozzle testing. If after checking there are no problems with the ink tanks, but the printer continues to print with streaks, you need to test the nozzle. To do this, go to “Start”, then select “Devices and Printers”, find your printer, press the right mouse button and select the item “Printer Properties”. In the window that opens, click on the “Settings” item. After that, go to the “Service” tab, and then select the “Nozzle check” item. However, the test pattern may vary depending on the type of printer. Modern models provide testing of nozzles on the device itself. The verification aLGorithm depends on the model, it is indicated in the instructions for a specific product.
  • Cleaning the print head. Inks used in inkjet printers dry faster than laser-type counterparts. With prolonged simple appearance of stripes during printing is not uncommon. Ink can clog nozzles after 2 weeks of inactivity. Sometimes the print head gets clogged in 3 weeks. To solve the problem in the installation program there is a special utility “Cleaning the print head”.

This procedure saves ink consumption. If you forget about it, the ink will start flushing the nozzles on its own during subsequent printing, consuming the cartridge. The cleansing procedure can be carried out at once 2-3 times. After that, let the printer cool down without touching it for 1–2 hours. If this does not help, then the head will have to be cleaned manually.

If the nozzles or nozzles of the print head are dry, you can try to solve the problem programmatically or physically. You can try to soak the cartridge. To do this, take it out, put it on a napkin on the table. With a little effort, it is pressed against the table with nozzles, trying to press with fingers on both sides. If this does not help, and paint does not come out, you need to try a software solution to the problem. To do this, open the “Printer Properties” and select the “Maintenance” tab. Next, alternately select the first 2 tabs (“Cleaning” and “Deep Cleaning”).

If the “Nozzle Check” and “Cleaning the Print Head” commands do not work, you can try flushing it with a special liquid. If this does not help, all that remains is to replace the cartridge.

  • Cleaning the encoder tape and disk. When the printer prints pages with different strip widths, the encoder disc must be cleaned. The desired part is located on the left of the paper feed shaft, it runs along the movable carriage and is a transparent plastic film with markings. During the operation of the printer, these markings become covered with dust and ink may remain on them, which will dry out over time. As a result, the sensor does not see them, and the paper is positioned incorrectly. To solve the problem, you need to wipe the disc with a soft cloth, soaking it with a special cleaning agent or a cleaning agent “Mister Muscle” for cleaning Windows with ammonia. After that, you need to wait about half an hour so that the treated surface is completely dry. Do not use acetone: this erases the markings. During cleansing, you need to be extremely careful. If the strip comes off the mounts, you will have to disassemble half of the printer to put it in place.

Inkjet

An inkjet printer can strip when:

  • clogged nozzle;
  • contamination of the encoder disk;
  • improper ink supply;
  • poor ink quality;
  • misalignment of the print head.

Drying of ink may be a probable cause of a print defect. This happens when the printer is not used for a long time. In addition, the device will strip when printing when air enters the print head. Sometimes the cause of the problem is the overlapping of the ink loops of the CISS. The product may print poorly with poor quality ink. Another reason may be shaft deformation, which is typical with prolonged use of the printer. And also defects in printing may appear when the ribbon or sensor is dirty.

However, you should not immediately throw away the equipment, because you can identify the problem and fix it yourself. Often, the cause of a defect that has appeared can be determined by the type of stripes, namely:

  • multicolored or white stripes indicate improper ink supply;
  • vertical line breaks indicate printhead misalignment;
  • white stripes at an equal distance from each other occur when the encoder is clogged.

Laser

The reasons for the appearance of streaks when printing on a laser printer are as follows:

  • the toner has run out;
  • the drum unit is worn out or damaged;
  • Waste toner hopper full
  • there is mechanical damage;
  • there are problems with the metering blade.

As with inkjet printers, sometimes you can understand the cause of a print defect by looking at the stripes themselves. For example, white vertical stripes that grow with each new sheet indicate the need to refill the cartridge. Vertical stripes of different widths indicate mechanical failure of the device. If the printer leaves black spots or dots on the paper during printing, the waste toner box is full. Black dots and a broken line around the edge of the sheet indicate that the drum is worn out. When dark streaks or faint vertical streaks appear on the pages, the problem lies in the metering blade.

The cause of the defect may lie in the deterioration of the magnetic shaft. He is responsible for applying the powder to the drum. During use, the toner acts on the coating of the magnetic roller. If it is frayed, the printer prints pages with white, irregular stripes. In addition, the color of the text also changes. Instead of black, it turns gray, and the pattern fill is uneven. However, the magnetic shaft often has to be changed along with the dosage blade. It also causes printing defects.

Why does the printer print with stripes and what to do?

Almost every printer user sooner or later faces the problem of printing distortion. One of these disadvantages is printing with stripes. From the material of this article, you will learn why this happens and what needs to be done to solve the problem.

Laser

Laser printers are not only color, but also gray and white. In most cases, the appearance of streaks on the print is due to the condition of the used cartridge. Typically, any new device of this type contains cartridges with a minimum amount of powder. It ends faster.

    Replacing the toner. If the color changes during printing and white streaks appear in the middle of the text, you need to replace the cartridge. It is useless to take out and shake the toner in an attempt to print a few more pages. It will not help, do not knock the cartridge on the table or floor. From this, mining will begin to pour out of the sump. Waste printing shortens printer life.

You need to replenish or replace the cartridge if streaks appear in the middle of the sheet. If the stripes are dark and sinuous, this indicates a low quality of the powder used. When the toner level has not reached the critical mark, you should pay attention to the supply system. In this case, you cannot avoid contacting the service center.

In this case, you must not pour more powder into the compartment than is necessary, otherwise the stripes will continue to decorate the pages when printing.

  • Replacing the drum unit. The imaging drum of laser printers has a coating that is sensitive to optical radiation. During use, this coating will wear off and the quality of the printed pages will suffer. Black streaks appear on the right and left sides of the print; they do not disappear after replacing the toner and become wider. Removing them will not work: you will have to change the drum unit. If you delay the moment of contacting the service, other elements of the device may be damaged.
  • Damage to the cartridge if dropped. If the problem appears after accidentally dropping the cartridge, the powder-retaining rubber seals may not resist when struck. As a result, the powder will fall on the sheet, leaving streaks and spots on it, not only on the side, but anywhere. You will not be able to do anything with the toner: you will have to buy a new one.

To eliminate the problem of damage to the cartridge, remove it from the printer, inspect for cracks and loose parts. In addition, the places where the bolts are screwed in are inspected. Then they shake slightly, slide the curtain near the shaft and see if the powder is poured. If everything is in order, inspect the mining bunker.

Few people thought about the fact that when this compartment is overfilled, some of the powder gets out. This results in wide black stripes on the pages. To prevent this, it is necessary to remember about prevention. You need to clean this compartment every time you refill toner yourself.

  • Software problems. The streaking may be caused by a software malfunction on the device. This could be due to a power outage, user damage, or viruses. If the stripes after other manipulations continue to decorate the pages when printing, you will have to reinstall the driver. It is usually included with the device. If the disc is damaged, you can download the driver from the official manufacturer’s website.

What to do?

To solve the problem, you need to build on the type of printer.

Stripes in one place

There are several common reasons why a printer prints with defects. The first is the printer shaft, which can deform due to the long service life of the product.

Violations may also occur due to the ingress of a foreign object, paper clip or pen inside the mechanism. It is necessary to inspect the cartridge and the actual “inside” of the printer, remove the clogging.

READ  The Printer Writes No Toner And The Cartridge Is Full

The printer can print with stripes if the thermal film is damaged, it is available in different colors. gray, orange, blue, green, etc. It can emit a specific rustling sound, especially if toner stripes appear on the edge of the sheet.

Damage to the drum unit

If a dashed black line appears at the edges of the sheet, then this indicates that the drum is worn out; with its further use, it is damaged more and more, which leads to its unusability. Therefore, you can no longer print, but you need to urgently restore the part.

Correct threading is of great importance, contamination of the blade leads to a deterioration in print quality, over time, faint, and then longitudinal black stripes will appear.

It is also unfortunate that when the waste container is full, toner residues can destroy the surface of the primary charge roller. Such defects cannot be ignored, because the service life of the printer mechanism will depend on timely technical assistance.

The printer prints with stripes: what to do?

Your printer prints in stripes and you don’t know what to do? First of all, you need to trace the dynamics of the occurrence of defects during printing, and then try to eliminate the violation.

Why does the printer print in stripes??

Over time, any device can significantly reduce print quality, and therefore various problems arise that reduce the efficiency of printing technology. For laser and inkjet printers, malfunctions and methods of their elimination vary significantly.

Jet printer

Waste Toner Box Full

Black dots may appear on the sheet, which will merge into one wide stripe. The reason for this defect: poor cleaning, and therefore requires refilling, it is advisable to use the services of another service center.

If the stripes are in different places every time

In most cases, the problem lies in the violation of the integrity (tightness) of the cartridge, it is easy to check and fix the problem. You need to take out the cartridge and shake it, if you do not want to get dirty, then entrust this procedure to a specialist.

What to do if the printer prints in stripes and how dangerous it can be?

When this problem happened to me for the first time, I was very puzzled and seriously alarmed, however, after reading articles on the Internet about this, I quickly figured it out. So now I am happy to share my many years of experience with other people.

Below will be described a clear sequence that I followed when eliminating this kind of defect. I draw the reader’s attention to the fact that some details in terms of the interface differ for different printers, but the essence of this operation does not change. Personally, in my case, stripes were eliminated when printing on the Epson L355 printer.

What is the mechanism of this kind of problems?

First, let’s look at the causes of streaking when printing on an inkjet printer. I draw your attention to the fact that now it is much better to buy printers with CISS, since their use is much more economical than purchasing cartridges. So, the reason that leads to striped printing is that the print head is clogged, through which the pattern is applied. That is, when ink is supplied, the microscopic channels connected to the print head become clogged. Or another reason is the ingress of air into these channels. This is due to the fact that printing continued when the ink has already run out. But in any case. the result is one, only in the second case there is a risk of “burning” the print head.

The appearance of streaks when printing on the printer. do it yourself.

Any person who will work with a printer sooner or later is faced with the problem of stripes. That is, when printing an image, a picture is obtained that is not the same as on a computer screen, but with a large number of stripes, which, of course, significantly impair perception. It is especially bad when it comes to color printing of some flyers or business cards. it turns out not advertising, but some kind of anti-advertising.

I was engaged in the production of printed advertising materials and am familiar with this problem firsthand. The appearance of stripes during printing is one of the most basic problems of the printing industry, which automatically entails a number of new ones. What is most interesting is that no one can avoid it, so you just need to clearly understand the reasons for its occurrence and know how to behave to eliminate it. Question by type. the printer prints with stripes what any user of printing equipment asks to do.

This complexity of use is more typical for inkjet printers (and it doesn’t matter whether there will be an outdated model with cartridges, at least some modern Epson equipped with a seven-color CISS. stripes appear in both cases). In the case of using “inkjet”, the most clear white stripes are obtained. But here we need to make a correction. not always the stripes can be exactly white. In the event that color printing is used, then the stripes can have a very different color. This is due to the fact that the printer creates different shades by mixing the primary colors, and if one of them is missing (problems with the supply from the CISS), then, accordingly, in some places there will be a “gap” of the other shade. For example, there may be pink stripes on a blue background.

However, a laser printer can also produce stripes, but in this case they will be smoother. This is because the toner cartridge is low on.

ALGorithm of actions to eliminate stripes.

The print head needs to be cleaned. To do this, do the following:

  • In the menu of the document that you are going to print, open the “Print” tab.
  • Next. open the “Printing settings. service” tab (or the same tab may be called “Properties”. service, depending on the operating system installed on the computer). Please note that in the picture, the arrows indicate the tabs that must be pressed:
  • Following this, you will need to select the “Nozzle check” menu item, insert paper into the printer and confirm the operation. It will look something like this: After cleaning the nozzles, you will be printed with stripes of four colors (or seven. depending on how many original colors your printer is working with). If there are line interruptions on these lines, you will need to perform another head cleaning. If all the lines of four colors were printed without problems, then you can safely work on, there should be no stripes.
  • In the event that cleaning the nozzles did not help, click “Cleaning the print head”. All actions are the same, again we look at the control line from the prints of four colors. If printing defects remain, head cleaning must be performed again.
  • There are also cases when even repeated head cleaning does not help. Then you will have to carry out technological cleaning. This operation consumes a very large amount of ink and is quite “painful” for the printer procedure in terms of the functioning of various parts. After performing the technological cleaning, in the overwhelming majority of cases, everything is working out, but if not, then you will have to take the printer to the service center.

Again, it should be understood that each such cleaning consumes a certain amount of ink, which leads to the need to reset the counter of the so-called “Pampers”. which is very problematic. So we should try to carry out such cleanings as little as possible.

Stripes when working with a laser printer.

This too may well be. In the event that the “laser” starts to produce stripes during printing, it is necessary to check three things and draw the appropriate conclusions:

  • Is there enough toner? Perhaps the problem is on the surface, and you just need to add toner.
  • Is the fotoval serviceable??
  • Is the cartridge itself defective??

In the vast majority of cases, you just need to add toner and that’s it. So everything is simpler here than with the “inkjet”.

Inkjet

Inkjet printers are refilled with liquid ink. When they run out, you can notice a change in shades. For example, instead of black text, the printer prints blue text, horizontal spaces, or white stripes dividing letters into 2 parts. Sometimes the printer even prints pages with transverse stripes over the entire surface of the sheet. Such a problem indicates an overflow of the hopper or the need to replace the squeegee.

In other cases, it is necessary to inspect the integrity of the thermal film. Toner should not spill from the cartridge. It’s easy to check: you just need to take out the cartridge and shake it slightly. If this causes your hands to turn black, you will have to replace the toner with a new one. Otherwise, you will not be able to fix the problem. However, before doing anything, you need to have Honor: the ways to fix the problem are different for inkjet and laser printers.

First, you need to figure out how to fix the defect of inkjet printers on your own.

Checking the ink level. If your inkjet device produces stripes when printing, you must first stop printing and refill the cartridges. You cannot ignore the problem, without paint you will not be able to carry out a nozzle test. In addition, a lack of ink will cause the nozzles to burn out. To do this, find software, install and run the program. Next, open a tab with a drawing of ink capsules. It can be named by different names (“Estimated Ink Levels”, “Printer Ink Levels”). Use the printer control panel to diagnose ink levels. A visual assessment will help you understand which ink needs to be replaced. Usually, when the level is critically low, an alert icon appears in the form of a yellow triangle.

Part of the text on the sheet is not printed in stripes

If part of the text or image is missing on the printed sheet, this indicates in most cases the end of ink in the cartridge. To fix this problem, refill the printer cartridge.

Please note: In a situation where the problem is not related to the cartridge, white streaks may appear on the sheet due to various “debris” falling on the printer shaft. parts of dried toner, screws, paper clips, and so on.

Stripes appear at the same distance from each other when printing

The appearance of black stripes at the same distance from each other during printing indicates that the connection between the magnetic roller and the drum is broken. The most common cause of this is improper cartridge refilling, which results in toner scattering. Overfilling the waste bin of the cartridge can also cause the problem. In such a situation, you need to refill the cartridge (if it was refilled incorrectly) or replace the components that led to a communication failure.

What to do if an inkjet printer prints in stripes

Let’s take a closer look at the causes, ways to diagnose and eliminate them.

If the printer is equipped with a continuous ink supply system (CISS), then you can check their level simply by looking at the refill containers. There is another way. In almost every modern device, there is a sensor that allows you to determine the approximate fill level of the container. You can check this indicator in the software that the manufacturer provides with the printer. And to solve this problem, you just need to refuel the containers or replace the cartridge.

If everything is in order with the ink level, then you should check the technical condition of the cartridge. To check the integrity of the cartridge case, you need to remove it from the printer, carefully inspect and shake it a little. This should be done over the pre-spread paper so as not to stain the surrounding objects. If defects are found in the case, the element must be replaced.

READ  How to connect an epson printer to Wi-Fi

Then you should check the integrity of the CISS loop. Perhaps a crack has formed somewhere or it was pinched during installation. Unfortunately, it is not always possible to fully check the cable without disassembling the printer, and replacing it is also a very difficult task that is better to entrust to specialists.

After checking the integrity of the CISS loop, check the condition of the filters for the air holes. During a long break in operation or after prolonged operation, the filters become clogged and cease to pass air normally. When they become unusable, they should simply be replaced with new ones.

Also a common cause is contamination of the encoder tape. This is a translucent plastic film that runs along the movable carriage. For cleaning, use a soft cloth soaked in detergent. After cleaning, you must wait 30 minutes to allow the encoder strip to dry.

Perhaps the most unpleasant breakdown will be the contamination of the print head. But manufacturers have provided an easy way to clean. In the printer software, there is a Maintenance tab where you can run the nozzle cleaning. True, not every inkjet printer has such a function.

If the software cleaning did not help or it is completely absent, then you should manually clean the nozzles with a special cleaning agent.

If, after carrying out all possible manipulations, the device continues to issue sheets with stripes, then it should be taken to a service center.

Troubleshooting

  • run the printer management utility (if you do not have it, install it from the disk that came with the printer upon purchase or from the manufacturer’s website);
  • open the section “Service” or “Service”;

This is what the Estimated Ink Levels tab looks like in the HP Printer Management Utility

In continuous ink supply systems (CISS), the level can be assessed visually, since the cans are transparent.

If the ink is low, the cartridge needs to be replaced or refilled.

The printheads in inkjet printers can reside in the cartridge or in the printer itself. The first option is implemented in the bulk of Canon and HP models, the second. in Epson. If you have a printer of the first type. to solve the problem, you can simply change the cartridge.

In cases where replacement is impractical (the cartridge is not fully used), or is irrelevant (replacing the print head in Epson printers is comparable to the cost of buying a new printer), you can try to solve the problem by cleaning.

At home, it is best to do this programmatically:

  • Insert a sheet of paper into the printer, run the management utility and open the “Maintenance” (“Service”) section.
  • Clean the print head and check the nozzles (nozzles, or, in other words, the “spray guns” that ink comes out of). These options are available in service programs for printers of any brand. Here are some examples:

Advice! If the problem persists, the cleaning should be repeated 1-2 more times. When this does not help, you can remove the dried ink from the print head with chemical liquids (at home, this is usually used for this “Mister Muscle”).

If you have CISS, make sure that the holes through which air enters the cans are free. If filters are installed in them, check if they are dirty. If air passes through the filters with difficulty, they must be replaced or removed.

Advice! If you rarely print, it is enough to turn on the printer at least once a week to prevent ink drying out. It is not necessary to print as some ink is forced through the nozzles of the print head after switching on. She does not have time to dry in a week.

Cleaning the print head also helps in the event of air bubbles, which happens after changing or refilling cartridges.

Damage to the printing mechanism is more likely to occur due to inaccurate handling during removal, and sometimes spontaneously, especially if you often and a lot of printing. Only the replacement of the defective part will help to fix the problem.

Why is it easier to solve this problem when a Canon or HP printer prints in stripes? Because, as we said, their printheads are located in cartridges. You just need to replace the cartridges with new ones.

However, remember that their price can be 50-90% of the cost of the printer. The high cost is due to the fact that the print head is much higher than the ink capacity.

In the event of a breakdown of the printing device in Epson or in another model with a print head in the printer itself, you will have to contact the service.

If the service utilities did not bring the desired result

When you have tried to fix streaking, ink smears, and gaps using the utilities from the Maintenance menu, but have no effect, check the following:

  • physical connection. the cables used by Canon to connect to the network (computer) and software settings. Perhaps, in some of the ports, the contacts began to loosely adhere to each other, as a result of which the printer loses its connection and does not completely print text or graphics;
  • maybe the system settings have changed somehow, and Canon is no longer the default printer. Or another port is assigned to it, which is not active. Go to the “Control Panel” on your computer, find the section “Devices”. “Printers and Scanners”. See which printing device is marked as default. Make changes if necessary. If the connection still does not work, right click on the printer icon in the OSD menu and select “Properties”. Check if there is a check mark next to the correct port. Double click on the printer icon to open the queue of jobs (single pages, entire documents or images that have been printed). Cancel all jobs in the list and try to print them again. If your printer is connected to a USB port, connect it to a different connector;
  • uninstall the driver on the computer, search the support site for a new (or more suitable) version of the driver, install it;
  • check the condition of the cartridges. Sometimes the reason for printing defects is trivial. out of ink. If ink is present, but it prints stripes, try removing the cartridges from the printer and inspect them carefully. Defects can be caused by worn nozzles or loose ink cartridges. Reinstall them correctly, and to make the fit as tight as possible, place a thick (10 mm) pad of foam rubber or several layers of paper on top of the container with paint.

Cartridges can be tricky. Since these ink tanks have a built-in ink level control chip, physical damage to the chip or glitches at the software level will negatively affect the printing process. Then it is better to replace the old cartridges with new, high-quality ones.

Usually, if there is a problem with the absorber (pampers), the printer gives an error message and blocks printing. The pampers need to be replaced or cleaned, then the print function will be available again. But this will require skills in assembling and disassembling electronic equipment. Very few users will be able to complete this task on their own.

Remember that the printer is a device that needs to be treated with care. If the above methods did not help to solve the problems with printing, it is better to contact the service center for qualified assistance.

Review article: what to do if the printer prints with stripes.

Watch this video on YouTube

What to do?

To solve the problem, you need to build on the type of printer.

The most common reasons

Let’s take a look at the main reasons why a color laser printer prints in stripes and what to do in this case:

  • Try checking the ink levels. To do this, run the Ink / Toner Check in the device maintenance settings. If the level approaches a critical level, refill toner.

Sometimes, when the device is idle for a long time without printing, it may need to be cleaned. What to do in this case? There is a “Cleaning” item in the device settings. which will allow you to clean up and solve the problem.

The printer prints with stripes: looking for ways to solve the problem

What problems users face and how to solve them?

Let’s analyze the most common situations associated with the appearance of defects in printing documents, and what to do with them:

  • the most common problem is white streaks that get bigger as you print. This is the simplest and most “harmless” option. little toner. When you print repeatedly, toner runs out and the lack of toner affects the print quality.

Important! Someone advises to shake the cartridge vigorously so that the toner is evenly distributed throughout the shaft. This can allow you to print another 10-20 pages, but this should only be done in extreme cases, since the toner is already running out and subjecting the cartridge to such tests, you shorten its life. If streaking starts to appear during printing, it is best to refill with toner.

  • Also, sometimes there is such a problem that after refilling the cartridge, the printer prints in stripes, what should I do in this case? First you need to check if there is enough toner or, on the contrary, if there is an excess of toner or if the toner buffer is full.

To solve this problem, clean the cartridge, remove excess toner from the buffer.

  • When the printer prints with a black stripe around the edge (side). what to do with this problem, all owners of devices with such a malfunction want to know. This situation occurs with frequent and prolonged printing. The cause of this malfunction is the deterioration of the drum unit. And simple cleaning won’t help here.

The solution is to replace the drum unit or cartridge as a whole.

  • A wide band or gray sheet occurs when the toner buffer is full. When the buffer is full, the excess can spill out during printing, so you should always clean it when refilling the cartridge. Also, such a problem can occur when a foreign object falls on the metering blade. as a result of which more toner is supplied to the print than necessary.

Solution: clean the buffer, check the metering blade for foreign matter.

  • Vertical stripes all over the sheet. If they appear every time in a new way, then most often this means a cartridge leak.

Solution: Checking the cartridge and seals for damage, cracks or gaps.

  • It happens that the printer prints with spaces and horizontal stripes. what to do in this case? The reason for the black horizontal lines at the same distance from each other is the problem of the shaft and drum, namely, the violation of contact between them.

Solution: From cleaning the waste buffer and refilling the cartridge, to replacing it. The specialist will be able to determine the cause of the error by the nature of the defects.

If these options did not help, then to answer the question why a Canon printer or any other brand prints in stripes, only the manufacturer’s service center will help you. Canon, Epson, Samsung and others. Some problems can be identified only by getting acquainted with the contents of the device, for which you need to have the proper qualifications, so you will not be able to do anything yourself in such a situation.

NNCXV.INFO 2021