How to clean up toner on a brother printer

Soft toner reset

Developers create additional maintenance functions for their equipment. Among them is a paint dumping tool. It runs only through the built-in display, so it is not suitable for all users. If you are that lucky owner of a device with a screen, follow these steps:

  • Turn on the all-in-one and wait for it to be ready to go. During the display of the inscription “Please wait” do not need to press anything.

clean, toner, brother, printer

Next, open the side cover and click on the “Clean” button.

On the screen you will see a question about replacing the drum, to start the process click on “Start”.

Close the side cover if the corresponding message appears on the screen.

Now you can go to the menu, move around it using the arrows to get acquainted with the state of the counter at the moment. If the operation was successful, its value will be equal to 100%.

As you can see, zeroing paint through a software component is not difficult. However, not everyone has a built-in screen, and this method is not always effective. Therefore, we recommend that you pay attention to the second option.

Brother hl 2130r lit toner how to clean

The Brother HL-2130R and HL-2132R printers have a built-in toner counter that counts the number of pages printed. If the corresponding indicator is on, the printer considers that the cartridge is already empty and requires a new one. He doesn’t care that you refueled him 15 minutes ago.

There are two ways to reset the toner counter: software and hardware. It’s easier to program, so let’s start with it.

How to reset the drum counter?

In some cases, office equipment asks to replace the drum unit. If the device prints at the same time, then there is no point in changing this part. unless, of course, the imaging drum has any mechanical damage or defects. To solve the problem, it is best to reset its counter. For this purpose, follow these simple steps:

  • Turn on office equipment, open its front cover.
  • Hold “Start” for about 4 seconds.
  • As soon as all indicators on the panel light up. release the previously held down button.
  • Now you just have to close the device and make sure that the zeroing was successful.

Almost all Brother printers and MFPs are equipped with a built-in mechanism that keeps track of printed pages and blocks ink when it is supposed to run out. Sometimes users, after refilling a cartridge, encounter a problem in which the toner was not detected or a notification appears asking to replace it. In this case, you must reset the ink counter to continue printing. Today we will show you how to do it yourself.

Method two: software

If the question of how to reset the Brother-HL2130R printer in the described way has not been resolved and the device still does not print, then resort to soft reset of the toner.

  • To do this, you just need to turn on the device, open the cover (front) when the engine stops making noise and turn it off again.
  • Press the “Start” button, turn on the device and hold one of the named buttons until all indicators start blinking and light up.
  • To further reset the counter in this way, release the “Start” button and after all indicators go out, press “Start” 2 times.
  • As soon as the 3 lights start to light, click on “Start” 5 times! If the “Error” indicator flashes, close the front cover.
  • After the printer has warmed up, the Ready light should come on. Be sure to do a test print.

Programmatic way

  • Turn on the printer.
  • When the engine stops making noise, open the front cover.
  • Turn off the device.
  • Press the [Start] or [GO] button and turn on the printer.
  • Hold the [Start] / [GO] button until all indicators light up.
  • Letting go of the button.
  • As soon as the indicators go out, press [Start] / [GO] two times. The top three indicators should light up.
  • We press [Start] / [GO] 5 times. The “Error” indicator should be blinking.
  • We close the front cover. The Ready light should be flashing. The printer is warming up and the Ready / Ready light should be on.

How to reset the toner counter for your Brother printer

The instructions below will work best for most Brother printing machines as they are all similar in design and quite often include the TN-1075 cartridge. We’ll look at two ways. The first is suitable for users of MFPs and printers with a built-in screen, and the second is universal.

Hardware method

The same as resetting the counter of the Brother DCP-7057R printer. Here I will only give a video.

The above methods are suitable for both Brother HL-2130R / 2132R / DCP-7057R starter cartridges and regular ones. If you bought a regular one, then there is another way to reset the Brother toner counter. check the box in the cartridge to the desired position. For details, see the video at the end of the article.

Method one: hardware

  • You can reset the cartridge counter on the printer from Brother, if it stopped printing due to blocking, using the hardware method. For this:
  • Turn on the office equipment, wait until the mechanism stops functioning (can be determined by the subsided noise), then open the lid.
  • Locate the lever to the left of the cover. Then carefully disconnect it, and then try to drown it in the office equipment case.
  • Now you can gently pull out the cartridge and separate it from the drum unit.
  • Insert the drum unit back into the printing unit and press down on the sensor that opens the front cover with a straight screwdriver.
  • Hold the checkbox and wait until the gears come into action. release it, and then clamp it again. Repeat this action a couple of times within 4 seconds.
  • After waiting for the mechanism to stop functioning, release the sensor on the right, which was previously clamped with a screwdriver.
  • Pull out the lever on the left side. Attach it to the cover (front).
  • Take out the drum, connect to the toner cartridge, reinstall the part, close the covers. Run a zeroed device, do a test print.
READ  How To Connect Brother Printer To Computer

Zeroing the drum unit

The Brother DCP-7057R MFP has a drum cartridge consisting of a toner tube and an imaging drum. Each of the elements has a separate sensor that counts the resources used. The sensor’s aLGorithm is based on the fact that the drum can produce no more than 12 thousand copies, and as soon as the figure is reached, the work is blocked, and a notification appears on the screen about the need to replace the drum.

If there is no damage on the surface of the photocell, it is not necessary to replace the shaft; to eliminate the error, simply reset the counter.

Clean the corotron (charge roller) before resetting. Move the blue slider on the cartridge from side to side. If this does not fix the problem, try resetting the counter.

  • Turn on the MFP.
  • Wait for the equipment to warm up and get ready for work.
  • Open the lid and click on “Clear”.
  • The screen should display the message “Have you replaced the drum unit?”.
  • Press the “Up” and “Yes” arrows alternately.
  • When the display reads “Accepted”, close the cover.
  • Reboot the machine.

Hard reset

The zeroing method is not suitable for cartridges that come in the starter kit with the Brother DCP-7057R printer, since the machine does not have a special flag.

  • Connect the device to the network. Waiting for the testing process to complete.
  • Open the door on the case.
  • On the left side, find a lever that you disconnect and hide in the body.
  • Remove the refilled cartridge and divide it into two parts: the toner bottle and the photo roll.

How to reset the toner counter on the Brother DCP-7057R printer

It is necessary to reset the Brother DCP-7057R toner counter if the machine displays a “Replace Toner” or “Toner Low” error. This message is displayed after installing a pre-filled cartridge or when very little powder dye remains.

The device is equipped with a chip that keeps track of the number of sheets printed. This is how the toner level is determined. For example, it is programmed that after printing 1000 pages, work will be blocked with a notification about the need to replace the powder. But this is not always correct, because each sheet is filled with ink in different ways and the toner in the cartridge may still be enough to print a certain number of sheets.

In any case, it is better not to risk it and refuel the container. But this will not help remove the notification and make the printer work after refueling. It is imperative to perform a reset so that the device removes the blockage and starts counting the ink consumption again.

Via the printer menu (software)

First, try to reset yourself through the built-in menu of the device.

  • Power on the printer.
  • Wait until the equipment stops making noise and switches to operating mode.
  • Open the cover on the front of the case.
  • Press the “Cancel” button on the case. On different devices, the button may be called “Stop”, “Back” or “Clear”.

We reset both counters at once

  • Turn off the device.
  • Press the “Menu” key and at the same time the “On” button on the MFP.
  • The message “MAINTENANCE” appears on the screen.
  • Look for the line at number 84 and click “OK”.
  • When the inscription “PROCESS CHECK” appears, click on “OK”.
  • After displaying the inscription “PLZ POWER OFF / ON” turn off the device.
  • Turn on Brother, the screen will display the message “PROCESS CHECK”.
  • Go to the subsection “RESET TONER COUNT” and confirm the zeroing of the cartridge by pressing “Ok”.
  • Return to the previous menu and, to reset the photovalue, go to the “RESET DRUM COUNT” menu and also confirm by pressing the “Ok” button.
  • Turn off the MFP.
  • Again, hold down the “Menu” button together with the inclusion.
  • When “MAINTENANCE” is written on the screen, go to “PROCESS CHECK” and with the “Ok” button activate the option “CHEKER MODE OFF”.
  • If the reset is successful, the display will show “PLZ POWER OFF / ON”.
  • Reload the technique and print the probe.

Instead of English inscriptions, Russians can be displayed on your screen.

78 Comments。

TIME FROM 4 YEARS IT WAS, BUT SO I DIDN’T CAREFULLY READ IMMEDIATELY, I GENERAL IN ALL THIS “KETTLE”, BUT THERE IS EVERYTHING IN DETAIL AND THE MAIN IS SHOWN WITH THE PICTURES! VERY, WELL, IT HELPED VERY MUCH, THANKS YOU, MAN-HEAD WITH BRAINS, THAT HOW DO I HELP

Thank! Good advice from a good person!

Thank you, it worked the first time, helped out).

Let’s look at how to reset the counters for Brother HL-1110R, HL-1112R, DCP-1510R, DCP-1512R, MFC-1810R, MFC-1815R printers. These models use one cartridge, TN-1075, so the toner and drum counters are reset in the same way.

Check

You can check if the Brother DCP-1512R cartridge has been reset to zero by printing the “Custom Settings” report. We press

READ  Epson L4150 Printer Does Not Print

[Menu] [4. Device Information] [4. Custom Settings] [OK] [Start]

The printout shows 100% toner and drum life. By the way, by periodically printing this report, you will see that the Brother DCP-1512R imaging drum is nearing its end of life, and you can replace it in time.

Resetting the BROTHER HL-1110R / DCP-1510R counter
After the machine prints a certain number of pages. it stops printing.
And one refueling of starter cartridges is not enough due to the lack of a reset flag (unlike purchased ones). it is necessary to manually reset the toner counter.
1. It is necessary to open the cover of the printer and take out the drum cartridge, along with the toner cartridge. Drum cartridge Toner cartridge
2. Remove the toner cartridge from the drum cartridge
3. Insert the drum cartridge without the toner cartridge into the machine
4. Place your hand through the paper feed tray and into the machine and pinch the reset flag on the left. 5. Close the cover of the printer. The motor starts rotating.
6. Release for 1-1.5 seconds and press the reset flag again, hold it until the motor stops.
7. If the green LED is on. the counter is reset. insert the toner cartridge into the drum cartridge and print.
If the red LED is still on, then repeat the procedure again. It may not work the first time.

Reset Toner Counter

How to do this through the device menu. I do not know yet. You can reset the toner counter of the Brother DCP-1512R manually, in the truest sense of the word. The process is simpler than the Brother DCP-7057R model. No need to disconnect and poke with a screwdriver.

We take out the cartridge and divide it into two parts (a toner block and a drum unit).

Insert the drum unit into the device.

We put our hand through the paper feed tray and press the sensor or lever (located on the left).

As soon as we hear the engine noise, release the sensor and after 1 second press it again.

We hold until the device warms up and dies down.

  • Open the lid, take out the drum unit, assemble the cartridge, insert it into the device and print.

You may not be able to reset the counter on the Brother DCP-1512R printer right away. Try to repeat the process by pausing before releasing the sensor for about 1 second after turning on the engine of the device.

Resetting the drum counter

Click [Menu] [4. Device Information] [6. Resetting the drum unit]

We press the arrow “Up” [∧] and the resource of the drum unit for the device is again 100%.

Reset Toner Counter for Brother Printers

The other day, relatives had a problem with the Brother MFC-1810R printer. After refilling the starter cartridge, the printer requires replacing the toner. To solve this problem, the printer needs to reset the toner counter. Since the TN-1075 cartridge is sold by Brother machines, the manual described here will work for DCP-1510R, DCP-1512R, HL-1110R, HL-1112R, MFC-1810R, MFC-1815R.

So, if your printer displays the “Change toner” error, then you need to do the following sequence of actions:

  • Remove the cartridge and paper from the printer.
  • Remove the toner from the housing. To do this, use the special lever on the cartridge.
  • Insert only the base of the housing into the printer. On the left you will see a button to reset the counter.
  • Put your hand through the paper tray, feel and hold the button with your finger.
  • Close the cover through which the cartridge is inserted.
  • Wait for the mechanism inside the printer to spin. As soon as it turns, release the counter reset button for 1-2 seconds (no more), then press it again until the mechanism inside the printer stops.
  • Then two options are possible:
  • If the printer clicked and gave an error “Replace toner”, then you could not catch the right moment in the previous step (step 6). Go back to step 1 and do all the steps again (I was able to correctly reset the toner counter only from the fourth time).
  • If you have done everything correctly, the printer will not peep, the printer display will not display the “Change toner” error. Now pull the cartridge base out of the printer, insert the toner, and then reinsert the assembled cartridge. The printer will now work until the next cartridge refill.

How to reset toner on brother dcp 1510r

Departure

Departure of the refueller to your office for free! Refueling in 15 minutes in a mobile laboratory! Quality, guarantee.

Tel. 268-28-14

Hardware method

The hardware method means interference with the mechanics of the device. Before starting work, you need to turn on the device and wait until its engine dies down (the noise will become noticeably quieter). Opening the lid.

Now we detach the lever on the left and put it into the body.

Next, we take out the toner cartridge. We take out the cartridge from the device using a special handle.

Next, you need to clamp the opening sensor with a screwdriver. So we can simulate a closed lid.

Next, you need to simulate the presence of a cartridge. To do this, hold down the checkbox, as soon as the gears start spinning, wring it out and then press it again. After that, repeat the procedure. squeeze and press. Thus, you need to hold down the flag 2 times in 4 seconds. It may not work the first time. In this case, you just need to try again.

Attention! When you press the checkbox a second time, you need it to remain clamped.!

Now you need to wait for the device to subside. After that, you need to release the very same panel closing sensor, which we held all this time with a screwdriver. After that, you need to connect the front cover with the lever (see the photo below, you need to pull out the lever that is in the MFP) and reinstall the assembled cartridge.

READ  How to scan a document with a kyocera printer

If you failed to reset the counter, then repeat the process, paying special attention to the point where you need to hold down the cartridge flag 2 times in a row. Thus, we let the MFP know that the cartridge is in place.

Almost all Brother printers and MFPs are equipped with a built-in mechanism that keeps track of printed pages and blocks ink when it is supposed to run out. Sometimes users, after refilling a cartridge, encounter a problem in which the toner was not detected or a notification appears asking to replace it. In this case, you must reset the ink counter to continue printing. Today we will show you how to do it yourself.

Soft toner reset

Developers create additional maintenance functions for their equipment. Among them is a paint dumping tool. It runs only through the built-in display, so it is not suitable for all users. If you are that lucky owner of a device with a screen, follow these steps:

  • Turn on the all-in-one and wait for it to be ready to go. During the display of the inscription “Please wait” do not need to press anything.

Next, open the side cover and click on the “Clean” button.

On the screen you will see a question about replacing the drum, to start the process click on “Start”.

Close the side cover if the corresponding message appears on the screen.

Now you can go to the menu, move around it using the arrows to get acquainted with the state of the counter at the moment. If the operation was successful, its value will be equal to 100%.

As you can see, zeroing paint through a software component is not difficult. However, not everyone has a built-in screen, and this method is not always effective. Therefore, we recommend that you pay attention to the second option.

78 Comments。

TIME FROM 4 YEARS IT WAS, BUT SO I DIDN’T CAREFULLY READ IMMEDIATELY, I GENERAL IN ALL THIS “KETTLE”, BUT THERE IS EVERYTHING IN DETAIL AND THE MAIN IS SHOWN WITH THE PICTURES! VERY, WELL, IT HELPED VERY MUCH, THANKS YOU, MAN-HEAD WITH BRAINS, THAT HOW DO I HELP

Thank! Good advice from a good person!

Thank you, it worked the first time, helped out).

Many Brother printers have a page counter feature. It serves to notify the owner of the machine that it is time to replace the toner. Unfortunately, such a case is very common when the counter stubbornly blocks printing, referring to the replacement of the toner. In this case, you just need to reset the counter. This can be done in three ways:

  • programmatically;
  • hardware;
  • by configuring the reset checkbox in the cartridge itself.

Please pay attention to the comments that have been left in this article. Users offer their options, perhaps they will help you like them.

Reset Toner Counter for Brother Printers

The other day, relatives had a problem with the Brother MFC-1810R printer. After refilling the starter cartridge, the printer requires replacing the toner. To solve this problem, the printer needs to reset the toner counter. Since the TN-1075 cartridge is sold by Brother machines, the manual described here will work for DCP-1510R, DCP-1512R, HL-1110R, HL-1112R, MFC-1810R, MFC-1815R.

So, if your printer displays the “Change toner” error, then you need to do the following sequence of actions:

  • Remove the cartridge and paper from the printer.
  • Remove the toner from the housing. To do this, use the special lever on the cartridge.
  • Insert only the base of the housing into the printer. On the left you will see a button to reset the counter.
  • Put your hand through the paper tray, feel and hold the button with your finger.
  • Close the cover through which the cartridge is inserted.
  • Wait for the mechanism inside the printer to spin. As soon as it turns, release the counter reset button for 1-2 seconds (no more), then press it again until the mechanism inside the printer stops.
  • Then two options are possible:
  • If the printer clicked and gave an error “Replace toner”, then you could not catch the right moment in the previous step (step 6). Go back to step 1 and do all the steps again (I was able to correctly reset the toner counter only from the fourth time).
  • If you have done everything correctly, the printer will not peep, the printer display will not display the “Change toner” error. Now pull the cartridge base out of the printer, insert the toner, and then reinsert the assembled cartridge. The printer will now work until the next cartridge refill.

How to reset the toner counter for your Brother printer

The instructions below will work best for most Brother printing machines as they are all similar in design and quite often include the TN-1075 cartridge. We’ll look at two ways. The first is suitable for users of MFPs and printers with a built-in screen, and the second is universal.

Programming method

This is the simplest way, requiring only a couple of button presses:

  • we turn on the MFP and wait until it conducts all the preliminary preparations and dies down;
  • open the front cover;
  • press the “Stop” button once (it can also be the “Cancel” or “Back” button);
  • press “Start”;
  • press “Up” once, and then several times “Down” until the zeros “00” appear on the screen;
  • done! Now just click “OK” and close the lid.

If this option did not help you, then move on to another method, which is described below. There is also a video below how this is done.

NNCXV.INFO 2021