How to Connect a Canon Pixma Printer

How to reset a Canon Pixma printer. Resetting Canon Printer Settings. How to and Why You Should?

Like any electromechanical equipment, printers need periodic maintenance. The complex of preventive work includes cleaning the print heads and ink supply channels, removing all kinds of dirt from the surfaces of internal parts, replacing the absorbent material (diaper), etc.

Preventive maintenance can also reset hardware settings, ink tank and absorbent counters. What is it, why do you need to do it? We will answer these questions and give related advice.

What is printer reset?

All modern Canon printers and all-in-one printer have their own operating system (firmware), central processing unit (main controller), RAM and ROM memory, I / O interfaces and other components inherent in any computer.

All this suggests that modern printing machines are capable of storing various information. These are both user settings and various system data:

  • The status of sensors that calculate the level of toner in the cartridges;
  • The fullness of the diaper. a device that absorbs ink, which are discarded from the surface of the printheads after the completion of the next printing cycle.
  • Custom settings.

Sensor readings on Canon printers can be reset, i.E. Return to factory values ​​or zero. There may be several reasons for resetting the settings and / or showing the sensors of cartridges and diapers.

Resetting hardware settings

Resetting hardware / software settings is usually done when there is any problem with the printer or one of the all-in-one printer functions. copy, scan, duplex, etc. During operation, various system and user data are recorded in the device’s memory. As is the case with any computer, the information stored in the printer’s ROM can be damaged or lost, as a result of which all kinds of errors occur in the operation of printing machines.

The reset function helps to solve various problems associated with the software component of the printer. Resetting the configuration also resolves communication interface problems associated with wired and wireless connection of printing machines to the computer and to the computer network.

Reset Cartridge Counter

Any modern printer is equipped with various sensors that help carry out all the functions of printing machines. Among them are sensors that are responsible for measuring the remaining level of toner in the cartridges and transmitting the received data to the main controller of the device. When the ink runs out, the operating system automatically blocks the printing function. Idling printheads can lead to premature wear.

When installing new, replacing, or refilling the installed ink tanks, the printer usually recognizes that the user has performed these procedures, and then resets the ink level counter. But for various reasons this may NOT happen. It is in THESE cases that the reset function helps, which will allow you to zero the readings of the ink level sensor, thereby unlocking the printer and it will be able to continue its work.

Detailed instructions for resetting the cartridge counter on Canon printers are on our website.

Resetting the diaper counter

Absorbent material or pads fills with waste ink as the printer is used. Their filling level is also read by a special sensor. When the diaper is full, the printing machine is blocked, it becomes impossible to work with it. As you might guess, the absorbent dump function removes this blockage.

It is much more difficult to determine the fullness of the diaper than the ink level, therefore the absorbent sensor often gives “false readings”. This is precisely what the absorbent fill level reset function is for.

It should be noted that the diaper counter can be reset only 2-3 times. If the absorbent is too full, ink will start to leak out of the printer body or, even worse, accumulate inside, which may cause various malfunctions, including burnout of the motherboard.

How to reset a Canon printer?

Each of the three reset functions listed above is triggered differently. It should also be borne in mind that in different printer models and all-in-one printer Canon resetting the settings and resetting the sensors is performed differently. Let’s go in order.

Reset

There are two ways to restore software / hardware settings to factory defaults. it will initiate a reset from the front panel of the printer or from a computer. The first method involves resetting by starting the required function from the printer’s LCD screen or by pressing the function buttons in a certain sequence. And on different models of Canon printing machines, this is done in different ways. For example, on most Canon i-SENSYS series all-in-one printer models (MF4450, MF4410, MF4580, etc.), this is done as follows:

  • Press the button “” (Looks like a head in profile), then the button “2” and “8”.
  • The printer enters the service mode.
  • Then click on the buttons “Copier”, “Clear” and “Clear All”.
  • Settings will return to factory defaults.

This is the same for many Canon PIXMA printer models:

  • Turn off the printer by pressing the power button.
  • Press the “STOP / RESET” button and, Do not release it, press the power button.
  • The printer should turn on, as indicated by the lit power indicator.
  • Release both buttons.
  • Then press “STOP / RESET” twice and hold it after the second press, then press the power button again. Release both buttons. the printer will enter the service mode.
  • To reset the configuration, in fact, you need to clear the EEPROM memory, in which the settings are stored. To do this, press the “STOP / RESET” button 2 times.
  • Turn off the printer by pressing the power button also twice.
  • Settings will be reset.

Detailed instructions for resetting the settings on a specific printer can be found in the technical documentation for the device and operating instructions.

The easiest way to reset the printing machines from your computer is to reinstall the driver. To do this, you will need the disc supplied with the printer or Internet access to download the software.

Resetting the ink counter

The counter reset procedure also depends on your specific Canon printer. In most cases, it is enough to press and hold the “STOP / RESET” (For multifunctional devices) or “Resume / Cancel” (For conventional printers) button for 10-30 seconds. Press the button immediately after the message about the end of ink in one of the cartridges is displayed on the computer screen and / or the front panel of the printing machines. If there are several ink tanks, this procedure will need to be repeated for each of them (only after the end of the toner).

In modern Canon PIXMA series multifunction devices, resetting the sensor shown can be done from the service menu:

  • Follow steps 1 to 5 of the instructions for resetting Canon PIXMA printers to enter service mode.
  • Press the “STOP / RESET” button 4 times.
  • Press the power button twice.
  • The counter will be reset.

As in the previous case, the exact instructions on how to reset the ink level should be found in the technical documentation and operating instructions for the existing Canon printer model.

Diaper reset

The reset procedure shown on the pad counter also depends on the Canon printer model. For example, in many MPC all-in-one printer models (MPC400, MPC600, etc.), the absorber can be reset from the LCD menu:

  • Put the printer in the service mode of operation by selecting the menu items one after another. “Menu”, “Copy”, “#”. If the screen displays a message like “SSSW”, then the printer entered the service mode.
  • Select “7. Printer” using the arrow buttons on the front of the device and press “OK”.
  • Next, select “5. Ink abs capa”, click “OK”.
  • The printer will prompt you for a Numeric value.
  • Enter “0”, then click “OK” and turn off the printer.

Detailed instructions for resetting the ink pad on Canon inkjet printers.

A universal way to reset the diaper sensors

Many modern Canon printers and all-in-one printers support the software to reset the absorbent. For this, there are special service programs such as Service Tool and General Tool. Consider the procedure for resetting the system counters using the Service Tool:

  • Put the printer into service mode using one of the above methods or according to the instructions for the existing printer model / all-in-one printer Canon.
  • Download and run the Service Tool.
  • In the first tab “Main” of the main window of the utility, find the section “Clear Ink Counter”.
  • Opposite the “Absorber” item in the drop-down list, select “All”.
  • Click on the “Set” button opposite the drop-down menu.
  • If the command is executed successfully, a dialog box will open with the message “A function was finished”.
  • Click OK.
  • The counter will be reset.

It is not recommended to reset the diaper counter more than two times.

How to reset Canon Pixma printer

Got an error with your Canon Pixma printer? Sometimes a quick reset. That’s all the device needs to fix the problem. Each Pixma model has a slightly different factory reset procedure, but they are all very similar. Problems are easily resolved through the control panel of the printer itself. However, a full reset may NOT be necessary if you are having general issues such as print lag or cartridge issue.

Factory settings

The Pixma printer menu provides access to factory settings, using this option will return all settings to factory specifications and may require reconnecting to your home network and going through the entire setup process again. To access the factory restore option, turn on the printer and open the menu. Use the directional arrows to navigate to the Settings menu and then to Device Settings. Click “OK” and select the “Reset settings” option; click “OK” again to start the process. On some Pixma printers, the Device Settings menu is accessible from the main menu without going to setup options.

READ  How to Refill Canon Cartridge 445

Resetting the ink cartridge

When you install a new ink cartridge, Pixma walks you through the cartridge alignment process before you can begin your new print jobs. Follow the menu prompts to align and print sample letter paper.

Refilled ink cartridges create a reset problem for Canon Pixma printers and there are several ways to fix this problem. For Pixma MP / MX / MG series printers, resetting the ink cartridges requires rebooting the printer to match the BCH technology. For other Pixma printers, see the instructions provided with the refill kit. To avoid problems associated with resetting cartridges, purchase cartridges directly from the manufacturer or an authorized supplier.

  • Turn off the power.
  • Press the Power button while holding the Stop button. Release the stop button while still holding the power button before pressing the Stop button two more times. After about 30 seconds, the printer will display “O.”
  • Press the Stop button four times before pressing the Power button twice. Press the power button again to turn off the printer and complete its reset.
  • Reset the ink cartridges by turning off the printer power and USB cables. Open the ink cartridge door while holding down the power button and reconnect the power cables while holding down the power button. Close the cartridge door, and then release the power button.

Troubleshooting General Problems

Common printer problems. For example, paper jams, replacing an ink cartridge, or occasional technical problems. May interfere with the execution of a specific print job and prevent it from passing through the system. In this case, the job remains in the processing stage and may interfere with the processing of future print jobs. Removing an item from the queue serves the same purpose as discarding, freeing up other print jobs.

On your PC, find the Devices and Printer option in the Start menu. Select your Canon Pixma printer and Right-click to select View What’s Printing. When the queue appears, click the item that is still processing to highlight the print job, and then click Cancel. “

Mac users Should open the System Preferences menu and then select the Canon Pixma printer. Click “Open Print Queue” and highlight the job causing the problem. Click Tasks in the main toolbar and then Delete Task. “

How to reset Canon Pixma printer

Is there an error with the Canon Pixma printer? Here is a handy guide to reset your Canon Pixma printer.

Sometimes a quick reset. That’s all your printer needs to fix a serious error or problem. Each Pixma model has a slightly different factory reset procedure. However, they all have a lot in common.

Reset your Pixma printer using the following methods:

Factory settings

  • The Pixma printer menu provides access to factory settings, selecting the next option reverts all settings to factory specifications, which may require connecting to your home network and going through the entire setup process again.
  • To access the factory restore option, first turn on the printer and open the menu. Now Use the direction arrows to go to the settings menu and then to “Device settings”.
  • Select “OK” and select “Reset settings”; select the OK icon again to restart the entire procedure. On some Pixma printers, the Device Settings menu is accessible from the main menu without going to Settings.

Resetting the ink cartridge

  • When a user installs a new ink cartridge, Pixma walks it through the cartridge alignment process before moving on to the next print session.
  • It is important to follow the menu prompts for alignment and then print a trial version.
  • Refilled ink cartridges create a reset problem for Canon Pixma printers, and there are several ways to solve this problem. For Pixma MP / MX / MG series printers, resetting a cartridge requires a reset of the printer in accordance with “BCH technology”.
  • For other Pixma printers, see the instructions that came with the ink cartridge. Refueling or refueling kit. To avoid problems related to resetting cartridges, purchase cartridges directly from the manufacturer or an authorized supplier.

Ink reset instructions:

  • First, turn off the power.
  • Now press the power button while holding the Stop button.
  • Release the stop button while still holding the power button before pressing the Stop button twice.
  • Then after about 30 seconds the printer display will show “O”.
  • Then press the Stop button at least four times before pressing the Power button twice.
  • Now press the power button to turn off the printer and restart it.
  • Stopped cartridges by unplugging printer power and various USB cables.
  • Finally, open the ink cartridge door while holding down the power button, and then reconnect the power cables while holding down the power button. Close the cartridge door and release the power button.

If the problem with Canon printer repair is NOT resolved, Contact the nearest technician or customer support center of the specified brand or manufacturer to reset the Canon Prisma.

How to Reset Ink Levels Canon 30-241 PIXMA IP / MP / MX / MG Series. BCH Technologies Customer Support Center

The following procedures can be used to reset the ink control of a Canon printer after installing refilled Canon Internal Ink Cartridges 30, 31, 40, 41, 50, 51, 210, 211, 240, or 241. In most cases, the error / warning must be cleared to enable printing. The procedures for resetting the waste ink bottle are described below.

NOTE: To install with Multiple Cartridges, you may have to repeat the procedure twice.

For PGI-5, PGI-9PBK, CLI-8, PGI-220 CLI-221 PGI-225 CLI-226 Cartridges PGI-250 CLI-251: These are new Canon ink cartridges with a chip built into each cartridge. If you just add ink, the printer still thinks the cartridge is empty. You have two options:

Printer Categories

Your printer can fall into several categories. You may need to try several ways to get it to work.

Category 1:

[30-211 ink] CANON PIXMA MP190, MP470, MX300, MX310, iP1600, iP1800, iP2600, MP150, MP160,

MP170, MP180, MP190, MP210, MP450, MP460, MP470, MX300, MX310, MP240, MP250, MP260, MP270, MP280, MP480, MP490, MP495, MX320, MX330, MX340, MX350, ip, MX410, MX4. Ip2702

[240-241 ink] CANON PIXMA MX452, MG3120, MG3220, MG2220, MG2120, MX512, MX522, MG4220, MX432, MX439, MG4120

Category 2:

Printers without LCD, i.E. CANON PIXMA iP1600, iP1800, iP2600, iP2700, iP2702

Category 3:

Canon PIXMA LCD / Display printer models.

Category 4:

All Canon PIXMA Printer Models.

Reset Pixma IP / MP / MX / MG Category 1 Ink Counter (Universal Reset Procedure)

  • When a message appears on the computer screen, select Stop / Reset, OK, or Resume,
  • Or select Stop / Reset, OK or the Resume button on the printer within 5 seconds.
  • Printing will continue if there is no ink.

Reset Pixma IP Category 2 Ink Counter (Procedure # 2)

  • Press and hold the resume button
  • Press and hold the power button; hold both buttons for 5 seconds
  • Release the resume button.
  • Press the resume button 5 times.
  • Release the power button. The blinking ink / power indicator should remain steady after a few
  • Printing will continue if there is no ink.

Pixma MP / MX / MG Series: General Printer and Ink Counter Reset Category 3 (Procedure # 3.A)

  • Press the power button to turn off the printer.
  • Hold the Stop / Reset button while pressing the Power button. While holding down the power button, Release the Stop / Reset button, and then press it twice in a row.
  • Wait about 20-30 seconds until the LED shows 0.
  • Press the Stop / Reset button four (4) times in a row.
  • Press the power button twice.
  • Turn off the printer by pressing the power button again. Printer is restarted.

Then reset the cartridge ink counter:

  • Unplug the power cord and USB cable from the printer.
  • Open the cartridge door and hold the power button.
  • Connect the power cables while holding down the power button.
  • Close the cartridge door and release the power button. Ink cartridge discarded.

Pixma “MP” Series: Ink Counter Reset Category 3 (Procedure # 3.B.)

Most MP200-400 series

  • Turn off your Canon MP printer and unplug it from the outlet.
  • Click the On button. / Off. “, Re-insert the cable.
  • Press the Stop / Reset button twice while holding the On button. / Off. “, Then release the On button. / Off. “. This will put the printer into factory mode.
  • Press the Right Arrow button until Delivery Mode 3 appears on the LCD. Click “OK” to select it.
  • Press the Stop / Reset button when you see the No Cleanup message. This instructs the Canon printer to print a test page.
  • Lift the Canon MP 470 printer lid and wait for the cartridges to move to the left. Then unplug the printer from the wall outlet.
  • Take out both ink cartridges and close the cover.
  • Plug the power cord back in and press the On button. / Off. “.
  • Put the cartridges back inside as soon as you see the message “Replace cartridges”.
  • Wait a few minutes for the printer to recognize the cartridges before printing.

Pixma “MP / MX / MG” Series: Ink Counter Reset Category 3 (Procedure # 3.C.)

  • Press the power button to turn off the printer.
  • Hold the Stop / Reset button while pressing the Power button. While holding down the power button, Release the Stop / Reset button, and then press it twice in a row.
  • Wait about 20-30 seconds until the LED shows 0.
  • Press the Stop / Clear button four times in a row.
  • Press the power button twice.
  • Turn off the printer by pressing the power button again. Printer is restarted.

Pixma “MP” Printer Series: Universal Ink Counter Reset Category 3 (Procedure # 3.D.)

Printer models from Canon MP140 to MP830 only

  • Turn on the printer.
  • Press and hold the reset button on the printer.
  • While holding down the Reset button, press and hold the Color Start button.
  • Wait 5 seconds.
  • Release the Color Start button and then Release the Reset.
  • Wait for the device to start configuring. This should take about 20 seconds.
  • No. “1. Should appear on the display, press and hold the “Tools” button, and now the letter “A” should appear on the display.
  • While holding down the Tools button, press and hold the Reset button.
  • Wait for the lights on the printer to stop flashing.
  • Release the “Tools” button and then Release the “Reset” button.
  • With the printer off but still plugged into a power source, press the power button while pressing and holding the Stop / Reset button.
  • When the Power LED turns on, press the Stop / Reset button two (2) times while pressing and holding the Power button.
  • When you release the power button and the Stop / Reset button (regardless of the order), the printer enters the service mode (. Waiting for a menu selection).
  • When the LED lights up green, press the Stop / Reset button The specified number of times in accordance with the function listed in the table below (each time the Stop / Reset button is pressed, the LED lights up orange and green alternately, starting from orange)
READ  How To Refill A Cartridge For A Canon Printer Yourself

Pixma IP / MP / MX / MG Series: Reset Ink Consumption Counter Category 4 (Procedure # 4)

  • 0 times Green. Turned off
  • 1 time Orange. Pattern printing
  • 2 times Green. EEPROM printing
  • 3 times Orange. EEPROM reset
  • 4 times Green. Reset the waste ink counter
  • 5 times Orange. Destination setting
  • 6 times Green. Deep cleaning of printheads
  • 11 times Orange. LCD button / test
  • 12 or more times. Return to menu selection

.

How to reset Canon Pixma ink cartridges?

How do I reset Canon Pixma ink cartridges? Canon Pixma ink cartridges are usually containers that contain the ink needed to print documents. It is very important to regularly check the ink cartridge levels. If the ink cartridges are below the rated level, replace them immediately. There are sensors inside the ink cartridges that allow you to check the ink level. It is recommended to use original ink cartridges compatible with Canon pixma printer. However, sometimes non-technical users DO NOT know how to reset Canon Pixma ink cartridges? Therefore, we offer easy ways to inform you about this.

Tech Support Expert. Is a reliable tech company known for its real solutions to all printer problems. Canon. Famous brand among printers and cameras. Millions of Canon printer users around the world. And we’re available 24/7 to help Canon printer users if they get stuck between any issues, one of the common issues that most users face. These are low ink cartridges. Sometimes you are low on ink when you are about to print a document, but we are not aware of it. You have nothing to worry about, we have the right solution for you. How to reset Canon Pixma cartridges?

connect, canon, pixma, printer

At Tech Support Expert, you will get the right and simpler solutions as we have a team of professional experts with technical backgrounds. You can call us anytime at our toll free number 800-742-9005 or write to us at support @ techsupportexpert.com.

How to reset Canon Pixma ink cartridges

A special chip is inserted. Chip function. Report low or out of ink in a cartridge. Printers. It is a technical device and has some disadvantages. One of the major drawbacks is that most printers will not work even if the ink cartridge is out of ink. In this situation, it is necessary to reset the Canon ink cartridge, which requires a chip reset designed for your specific cartridge model Chip resets are available as a single product and are even included in refill kits.

The following are the ways to reset the Canon Pixma Ink cartridge:

Remove the cartridge

First, remove the cartridge from the printer. Then insert the cartridge into the main channel of the reset device.

Chip must contact

Now you need to make sure that the ink cartridge chip should make contact with the contact plate of the reset device.

Press down on the cartridge

Press down gently on the cartridge for a few seconds. The LED on the chip reset device will blink several times. This indicates that the cartridge has come into contact with the microcircuit. Hold the cartridge in the same place for five seconds until the LED indicator turns on with a constant light.

Remove the cartridge

Finally, take out the ink cartridge from the chip reset device. You can follow the same procedure if you want to reload any other ink cartridge over the Internet. When finished, install the cartridge into the printer.

We assure you that by following the above steps you will be able to successfully reset the Canon pixma cartridges. This is a fairly simple procedure and should be followed by every printer user whenever the printer displays a low ink warning, even if there is not enough ink left in the cartridge.

How to reset Canon cartridges?

  • The first thing you need to do is press the power button to turn off the printer.
  • Second, hold down the Stop or Reset button while pressing the Power button. Release the Stop / Reset button by holding the power button and pressed twice in a row.
  • Then wait approximately 20-30 seconds until the LED does NOT display 0.
  • Now press Stop / Reset four times in a row.
  • Press the power button twice.
  • Turn off the printer, pressed the power button again. The printer has been reset.
  • Now, to reload the cartridge, disconnect the power cable and USB cable from the printer.
  • Then open the cartridge door and hold the power button.
  • Then reconnect the power cables while holding down the power button.
  • Finally close the cartridge door and release the button. The cartridge has been discarded.

Alternative way to reset Canon printer

Perform a factory reset

This is another way to reset Canon printer ink. You can get rid of this problem by performing a factory reset.

  • In the menu of your Canon printer, you will see the option to restore factory settings. To select the option to restore factory settings, you need to connect to your home network and go through the entire setup process again.
  • First of all, turn on the printer and open the menu to Access the factory settings. Use the directional arrows to navigate to the setup menu followed by “Device Settings”.
  • Select the “Reset settings” option and click “OK” to restart the process.

Why Choose Us to Solve Canon Printer Problems?

If you are looking for an IT support management partner, then we, the technical support expert, are ready to SUPPLY you with the best service. Below are some of the reasons why they chose us:

  • We solve problems faster and thus become the best player choice on the market.
  • Our company employs certified and experienced technicians.
  • Over the years, we have accumulated vast knowledge, which we share with our clients.
  • Tech Support Expert gives you the best technical guide for all your Canon printers.

Best Help For Any Canon Printer Problem

Find a technical support specialist and Contact them for any troubleshooting, driver, connectivity, or ink cartridge issues for your printer. Our technicians will provide you with the best customer support by phone or live chat. Now, don’t hesitate to buy yourself a stylish and affordable Canon printer, and for any support we just need to call 800-742-9005. To get help with your printer.

How to connect Canon Pixma MG3600 printer via Wi-Fi?

Connecting your printer via Wi-Fi is a convenient feature that frees your work area from wires. But manufacturers still cannot provide a simple and understandable way to connect equipment to a PC. In this article, we’ll show you how to quickly connect your Canon MG3640 over Wi-Fi. Here are some convenient ways.

Reference! The Canon Pixma MG3640 is an inkjet multifunctional printer, scanner and copier. Average. Main characteristics:

  • Printing. color,
  • Maximum image size. A4,
  • Ability to print text and images from both sides,
  • B / W printing speed. 9 A4 pages per minute,
  • Color print speed. 5 A4 pages per minute,
  • Main input tray 100 sheets.

Connecting using WPS

WPS is a standard for automatically creating a wireless network. Designed to simplify router configuration for ordinary users.

  • Before connecting, you need to make sure that there is a “WPS” button on the router,
  • Enable WPA or WPA2 encryption in the router software settings.

Attention! Under no circumstances is WEP, otherwise the MG3640 will NOT connect. You can check it in the wireless settings on the PC.

Completed the settings and checks, do the following to connect the Canon Pixma MG3640 to the router:

  • Turn on the printer, hold down the Wi-Fi button until the power indicator starts blinking.
  • Press the “Black / BW” button first, then “Wi-Fi”.
  • The power indicator should be solid green and the Wi-Fi indicator should blink faster.
  • On the router (Wi-Fi router), press and hold the “WPS” button for two minutes.
  • If the power indicator starts flashing, the connection is being established.
  • Both indicators are on, not blinking. the printer is connected to the router.

After the end of the procedure Do not forget to install the software, the driver from the official Canon website, and follow all the instructions.

Connecting without using WPS

In rare cases, the router does not support the security protocol. Then you need to immediately launch the software to download and install the necessary drivers, and do the following to connect Canon via Wi-Fi:

  • Insert the CD that comes with Pixma MG3640, or open the installation file from the manufacturer’s official website.
  • Such a window will appear on the screen. Do not press anything. We wait.
  • In the next window, click the “Printer Settings”.
  • The application checks for the latest updates. Wait further.
  • The software should detect the country automatically. If not, select the region manually.
  • We accept the terms of the license agreement.
  • We agree with the next window. Application asks for permission to send additional information about device operation to Canon.
  • Click on until the connection method selection window appears.
  • Choosing the first item.
  • The computer will search the Canon MG3640 on the network to connect via Wi-Fi. The process can take up to five minutes. Be patient.
  • When connecting the printer for the first time, the computer’s network connection will be disconnected for a short time.
  • The user manual will be displayed on the screen with detailed instructions for setting up Canon. Prepare the printer for connection. Check the correct display of indicators and buttons.
  • During setup, a message may appear on the screen: “Setup wants to access your passwords.” Click “Allow”.
  • Software, drivers and tools are being installed. We wait.
  • The Add Printer button appears on the screen. Click “Add”.
  • The found printer will appear in the Add window.
  • “Bonjour” device appears first, then “Canon IJ Network”.
  • Choose the second option, the printer is configured.
  • If Canon is being installed for the first time, the software will prompt you to adjust the printheads. Agree.
  • Start to run trial print.
  • Will complete the installation.
READ  How to Connect Canon Printer to Computer

Attention! During the final settings, the printer offers to install additional programs that allow you to adjust images, edit the number and volume of documents. Here is the installation of THESE utilities should be discarded. They only load the system by offering the tools that are in the Microsoft Office package.

Pixma MG3640 is set up and ready to go. Also, the technique can be connected to the computer directly, rather than resorting to the “mediation” of the router.

Connecting directly to a PC

For a visual aid for connecting a printer without a router, see the following

The router is not working, but the printer is needed? Following these instructions:

  • Hold down the “Wi-Fi” button until the power indicator does NOT flash.
  • Then press the “Color” button, then. the “Wi-Fi” button. The indicator next to her began to flash.
  • Run the previously downloaded driver from the official website.
  • Disconnect from a wireless network if connected to a PC.
  • In the “Select a method of connecting to a wireless network” select “Direct connection”.
  • The printer connects to the PC, all sensors stop blinking.
  • Canon will be displayed as a separate Wi-Fi network in the “Current Connections” section of the computer.

Advantage: Canon Pixma MG3640 is NOT dependent on the signal quality of the router. Disadvantage: PC does not have access to the Internet via Wi-Fi, which can interfere with comfortable work.

Connecting to MAC OS

But how do you connect a Canon printer to an Apple laptop? There is no floppy drive in the products of this company. You need to download the software to install the drivers and follow the instructions:

  • Double click on the downloaded file, will start the “Settings” process, then click “Open”.
  • On the next screen, press “Next”.
  • Enter your password to the system, allow the installation of a third-party tool.
  • Next screen. Click “Start setup”.
  • The program is looking for the latest updates. Can practice for a few minutes.
  • Specify the required region and country.
  • Confirm License Agreement.
  • Agree or opt out of the Extended Survey Program (sends all-in-one printer activity data monthly to Canon).
  • The computer is checking the status of the printer. Process Takes up to five minutes.
  • Select wireless connection.
  • Select the connected printer from the list of devices.
  • The user manual will be displayed on the screen with detailed instructions for setting up Canon. Prepare the printer for connection. Check the correct display of indicators and buttons.
  • A separate message will ask for access to passwords. Click “Allow”.
  • The latest drivers are installed on MAC OS.
  • The Add Printer button appears on the screen. Click “Add”.
  • The found printer will appear in the Add window.
  • “Bonjour” device appears first, then “Canon IJ Network”.
  • Choose the second option, the printer is configured.
  • Is MG3640 installing for the first time? The software prompts you to customize the printheads. Agree.
  • Press “Start” to start a test print version. In a separate window, set the number of copies, page size.
  • Will complete the installation of Canon MG3640.

Factory reset

If you need to connect the printer to a second computer, or connect through a new router, you must reset the network settings back to factory defaults. Do the following:

  • Hold red Resume button until LED blinks 21 times.
  • Release the button.

The network settings have been reset to factory settings. With these settings, printing and copying documents via a computer will not be available.

If anyone is interested, you can watch the review of the all-in-one printer, which is discussed in our article:

To connect your printer to your computer, you must follow the guide. If none of the methods works, you should make sure that the router is turned on and the computer is picking up the Wi-Fi signal. If you have any questions, write to us. in the comments or in the online chat. We are always happy to help our readers and subscribers! Thanks for attention!

Status: “printer is disabled”. How do I turn on the device? A few simple tips

Regardless of what printing device is used, very often users are faced with the problem that when sending a document for printing, instead of the result, the system displays a message that the device currently has the status “Printer is disabled”. How to enable it, and fix this problem With a few effective methods.

Possible problems

Before making a decision to fix the problem with auto products, you need to understand the essence of the problem.

Among all that can cause such disturbances in the operation of the device, the following can be distinguished separately:

  • No physical connection to a computer or power supply;
  • Activated autonomous mode of operation;
  • Dirty or empty cartridges
  • Stopped printing service;
  • Problems with device drivers.

Status: “printer is disabled”. How to turn on the device in the simplest way?

At the first stage, it is worth applying the simplest and, as it may seem to many, completely banal solution. When the system displays a message like “Printer status is disabled”, it will turn on the HP device or any other printer, or you can try the all-in-one printer by first disconnecting it from the power supply, and after a couple of seconds turned it on again.

In this case, as a rule, in all modern devices self-diagnostics will be performed (the LED will blink at this time), after which the printer will go into the ready state (the LED should be on constantly).

But in some cases this does not help, and the system again displays a warning that the status of the device is set to “Printer disabled”. How do I turn on the device? You need to check the physical connection with the USB cable. It turns out that the device driver is installed in the system (it seems to “see” it), but in fact the printer is simply absent.

On the other hand, if the LED flashes continuously when turned on, the problem may be that the cartridge is out of powder or ink. Therefore, it must be replaced with a new one. It also happens that the cartridge for some reason has surface contamination. In this case, it will be enough to wipe it and perform a complete restart of the computer with restarting the printer.

Status: “printer is disabled”. How to enable (Windows 7, device options)?

But most often the problems are related to software glitches or incorrect settings. To begin with, understanding the question of how to change the status of the printer “disabled” (how to turn on the device), you need to look at its state and the set parameters.

In the standard “Control Panel” you need to go to the printers and faxes section, in which you first need to find the required printer and make sure that the device for printing is set by default.

Next, in the device status window, you need to use the “Printer” menu and uncheck the checkboxes with the time period for pause printing (delayed printing) and using the offline mode of operation, if any. In theory, after that the state will change to “Ready”. Clearing the print queue sometimes helps.

Restarting the print service

But it may also happen that everything is in order with the printer itself, but the service responsible for printing, for some reason, has shut down or crashed.

In this case, you need to call the services section, Using the services.Msc command entered in the “Run” (WinR) console, find the corresponding service (“Print Manager” or Printer Spooler) there, stop it, disconnect the printer from the mains for about 60 seconds, after which it will start the service again and turn on the same device.

Fixing driver problems

Also, it is often the case that the system message appears about the disabled status of the printer can be observed in case of problems with the drivers (obsolescence, malfunctions, file corruption, etc.).

In this situation, you will have to completely remove the drivers from the system, at least from the same “Device Manager”. If they are displayed among the installed programs, it is better to uninstall from the programs and components section. After that, the best solution would be to download the latest driver from the equipment manufacturer’s website and then install it.

You can do it easier. If the driver is really out of date, or just doesn’t match the device type, you can use automated driver update programs like Driver Booster.

Using fixer utilities

Some users and experts recommend using special programs that allow you to fix problems of this kind automatically.

In the simplest case, a small Fix It Center utility from Microsoft is recommended for use, but the HP Print And Scan Doctor program is suitable for a more complete diagnosis and elimination of problems with printers of any type.

A few final words

Finally, Microsoft experts themselves recommend installing the latest updates when using Windows 10, but I think this is relevant to the problem insofar as.