How to Reboot the Printer After Refilling the Cartridge

How to restart your brother printer after refilling a cartridge

reboot, printer, refilling, cartridge

Almost all printers and all-in-one printers from Brother are equipped with a special built-in mechanism that keeps track of printed pages and blocks the ink supply when it is supposed to end. Sometimes users who have refilled a cartridge are faced with a problem in which the toner was not detected or a notification appears asking to replace it. In this case, you must reset the ink counter to continue printing. Today we’ll show you how to do it yourself.

How to reset the toner counter for your Brother printer

The following instructions will work best for most Brother printing machines as they are all similar in design and quite often equipped with TN-1075 cartridge. We’ll look at two ways. The first is suitable for users of all-in-one printer and printers with a built-in screen, and the second is universal.

Soft toner reset

Developers create additional maintenance functions for their equipment. Among them is a paint dump tool. It runs only through the built-in display, so it is NOT suitable for all users. If you are the lucky owner of a device with a screen, follow these steps:

  • Turn on the all-in-one and wait for it to be ready to go. When the “Wait” message is displayed, you don’t need to press anything.

Next, open the side cover and click on the “Clear” button.

On the screen you will see a question about replacing the drum, to start the process, click on “Start”.

Close the side cover if the corresponding message appears on the screen.

Now you can go to the menu, move around it using the arrows to get acquainted with the state of the counter at the moment. If the operation was successful, its value will be 100%.

As you can see, zeroing paint through a software component is not difficult. However, not everyone has a built-in screen, and this method is not always effective. Therefore, we recommend that you pay attention to the second option.

Manual reset

The Brother cartridge has a reset sensor. It needs to be activated manually, then the update will be successful. To do this, you need to independently remove the components and perform other actions. The whole procedure looks like this:

  • Turn on the printer, but do not connect to the computer. Be sure to remove the paper if installed.
  • Open the top or side cover to access the cartridge. Do this action taking into account the design features of your model.

Remove the cartridge from the equipment by pulling it toward you.

Disconnect the cartridge and drum unit. This process is intuitive, you just need to remove the latches.

Insert the drum part back into the device as it was previously installed.

The zero sensor will be located on the left side inside the printer. You need to advance your hand through the paper feed tray and press this sensor with your finger.

Hold it and close the lid. Expect the start of the work of the apparatus mechanisms. Then release the sensor for a second and press again. Hold until engine stops.

It remains only to mount the cartridge back into the drum part and you can start printing.

If, after a two-way reset, you still receive a notification that no toner was found or ink has run out, we recommend checking the cartridge. Refuel if necessary. You can do this at home, using the instructions attached to the device, or contact the service center for help.

We have covered two available methods to reset the toner counter on Brother printers and all-in-one printer. It should be borne in mind that some models have a non-standard design and use cartridges of the second format. In this case, the best solution would be to use the services of service centers, since physical intervention in the components can provoke device malfunctions.

Thank the author, share the article on social networks.

Internet, gadgets and technology. Reset Toner Counter for Brother Printers

The other day a problem with the Brother MFC-1810R printer arose in relatives. After refilling the starter cartridge, the printer requires replacing the toner. To solve this problem, the printer needs to reset the toner counter. Since the TN-1075 cartridge is distributed among Brother machines, the instruction described here will work for DCP-1510R, DCP-1512R, HL-1110R, HL-1112R, MFC-1810R, MFC-1815R.

So, if your printer displays the “Change toner” error, then you need to do the following sequence of actions:

  • Remove the cartridge and paper from the printer.
  • Remove the toner from the housing. To do this, use the special lever on the cartridge.
  • Insert only the base of the housing into the printer. On the left you will see a button to reset the counter.
  • Insert your hand through the paper tray, feel and hold the button with your finger.
  • Close the cover through which the cartridge is inserted.
  • Wait for the mechanism inside the printer to spin. As soon as it spins, Release the counter reset button for 1-2 seconds (no more), then press it again until the mechanism inside the printer stops.
  • Further two options are possible:
  • If the printer clicks and displays an error “Replace toner”, then you could not catch the correct moment in the previous step (step 6). Go back to step 1 and Do all the steps again (I was able to reset the toner counter correctly only from the fourth time).
  • If you did everything correctly, the device will not peep, the printer display will display the “Change toner” error. Now pull the cartridge base out of the printer, insert the toner, and then put the Assembled cartridge back in. The printer will now work until the next cartridge refill.

78 Comments.

TIME WITH 4 OO IT WAS TURNED OUT, BUT SO I DIDN’T CAREFULLY IMMEDIATELY READ ABOUT ALL THIS “dummies”, BUT HERE IS EVERYTHING IN DETAIL AND THE MAIN THING WITH THE PICTURES VERY, WELL VERY HELPED, THANKS YOU, CHAIRMAN with brains, THAT IS HOW I HELP

The first time, lovely!

Thanks! Good advice from a good person!

Thank you, it worked the first time, helped out).

It’s no secret that all Brother printers, especially laser printers, have an installed chip-like protection, which in some models is located on a cartridge. Thus, manufacturers of equipment for printing are trying to fight with companies that provide users with refilling the toner cartridge. Indeed, due to the availability of such a service, the sale of original (new) cartridges is significantly reduced. But, if you look at the situation from the point of view of the user, then paying a lot of money for a new cartridge, which costs almost half the price of a new printer, does not make sense. Therefore, Brother laser owners often resort to such a procedure as clearing or zeroing the counter, which you can do yourself.

Why reset the counter

Trimming is the procedure for changing equipment settings. The protection itself operates according to the following principle:

  • The manufacturer installs a special meter in the system;
  • The chip counts the number of sheets used during printing, and, after the cartridge has run out, signals this to the user, block the machine.

Each cartridge has its own resource. There are toner containers designed for 2,500 sheets, and sometimes. for 1,000 sheets. The chip is programmed according to the number of sheets. After exceeding the print limit, the message “Replace consumables”, “Toner empty” appears, or the indicator simply blinks. But, although you can add new toner, the chip will still consider that the cartridge is empty, and will not allow the machine to work. To get rid of this problem, a method was devised to reset the counter.

Resetting the TN-1075 cartridge

TN-1075 cartridge is quite common in Brother laser printers. It is installed, for example, in such models of devices as: DCP 1510r, dcp 1512r, MFC-1810R (1815R), HL-1110R (1112R).

To reset the counter on a TN-1075 cartridge, there are 2 methods, which are used depending on whether you have a starting model that does not have a crescent-shaped gear, or you have already purchased a replacement one.

Starter cartridge

So, if a message appeared in the brother printer: “Change toner”, then proceed as follows.

  • Empty the paper tray and remove the module from the machine.
  • Division cartridge from drum unit, pressed the blue key case.
  • Put the drum unit back into your brother printer. On the left side of it you can see a hole from which you can see the reset button.
  • There is only one way to click on this checkbox. It will only be possible to reach it through the tray, in which paper is put. You must remember where the checkbox is, as the reset will happen when the lid is closed.
  • Knowing where the button is, press it and close the cover of the unit. Don’t be afraid that something will happen to your finger. there are moving parts in this place. So, after closing the lid, the engine will turn on. As soon as you hear it work, immediately release the button and after 1 second press it again. Wait in this position until the engine stops.
  • You can tell that the operation was successful by the blinking green LED. If this does not happen, then repeat all over again.
  • Insert the cartridge into the drum unit. This completes the resetting of the counter in the brother printer.

Purchased Toner Cartridge TN-1075

Besides the fact that the counter can be reset with a button, there is another easy way to reset the brother printer.

  • Detach the cartridge from the drum unit and unscrew the side cover from the side where the gears are visible.
  • Remove the cover carefully to prevent the gears from spilling out. You only need to remove one gear, as shown in the following figure.
  • Next, you will see a crescent-shaped gear that needs to be returned all the way, as shown in the photo below.
  • The gear previously removed can now be reinserted.
  • Close the cover carefully so that the crescent-shaped gears DO NOT move.
  • Screw on the cap and insert the cartridge into the drum unit.

After all THESE actions, place the module in the printer.

Zeroing algorithm for laser models HL-2130R, HL-2132R, DCP 7055r and DCP 7057r

There are also 2 ways to reset the page counter in the HL-2130R (hl 2132R) and DCP 7055r (7057r) laser models: software and hardware.

Software way to zero the printer HL-2130R (2132R)

To soft reset the counter on your brother printer, do the following:

  • Turn on the device (after turning on you will hear the noise of the drive)
  • After the noise disappears, open the cover located in front of the unit;
  • Disconnect the device;
  • Press the “Go” button and Do not release it until the unit turns on again (the “ready” indicator should NOT be on)
  • Lower the “Go” key;
  • Press the “Go” key twice again;
  • Click on “Go” 5 times in a row;
  • Close the cover (front).

The “ready” indicator now lights up steadily. After THESE manipulations and overloading the machine, the Brother hl 2130r (2132) laser can be considered zeroed and ready to work.

Software reset all-in-one printer DCP 7055r

To reset the counter programmatically in the all-in-one printer dcp 7055r, follow the steps below:

  • Press the “Menu” key;
  • Then select “General settings”, then click on “OK”;
  • At the next step, select “Change toner” and again “OK”;
  • Using the arrows on the control panel, select “Continue” and press “OK”;
  • To exit this menu press “Clear”;
  • Counter has been reset.

Zeroing DCP 7057r by software

Zeroing the MFC DCP 7057r is slightly different from DCP 7055r:

  • Turn on the all-in-one printer and wait for the mechanics to quiet down;
  • After that, open the cover located in front of the device;
  • Click on the “Cancel” button (“Back” or “Stop”)
  • Press the “Start” button;
  • Press the up arrow key followed by the down arrow key several times until you see 2 zeros (00) on the display
  • Press “ok” and the front cover can be closed.
READ  How to Connect Printer to Laptop with Wire

In the case when these 2 methods did not help, then you can reset through the system menu all-in-one printer.

  • First check that your all-in-one printer is turned off.
  • Press and hold the Menu key.
  • Turn on the device while holding down the.
  • After you see a blinking inscription on the screen of the device, Release the “Menu” key.
  • Wait a while until the word “MAINTENANCE” is displayed on the screen.
  • Using the arrow keys, you need to find point 81, then confirm the selection by clicking on “OK”.
  • The screen will display the inscription “RESET DRUM COUNT” After pressing the “Start” button, the message will change to “RESET LIFE COUNT”. Press “Start” again.
  • Using the arrow keys, you need to select already item 96 and confirm with the “OK” key.
  • Let’s reboot the unit. To do this, you need to turn it off and turn it off again. This completes the resetting of the counter.

Hardware method of zeroing

You can also reset the all-in-one printer in hardware. To do this, proceed as follows.

  • After the all-in-one printer displays “Replace Toner”, pull the cartridge out of the machine.
  • On the starter cartridge you will see a black plug with a small stop, which must be cut off with a knife.
  • The next step is to remove the spring with the flag.
  • The spring should not be thrown away. You will install it if you want to change the starter cartridge for a purchased one.
  • Next, insert the cartridge into the machine, release the lever and hide (drown) it in the all-in-one printer.
  • Using a match or a screwdriver, you need to press the sensor, the case is located, which is responsible for the closed cover.
  • When you hear the mechanics work, press 2 times in the flag with a screwdriver. It is necessary to press so that you can make 2 clicks within 4 seconds. If unsuccessful, you can try again.
  • After the counter has been successfully reset, you will see an inscription on the screen (see photo below).
  • Now you need to print a test page that contains information about the status of the toner and drum unit. To do this, press the “Menu” key, select “Device Information” and “User Settings”. Confirm your choice by pressing the “Start” button.
  • If you did everything correctly, a test page will print.

At this stage, the all-in-one printer can be considered completely ready for work.

How to restart a canon printer after refilling a cartridge

Printer owners are constantly faced with the question: how to reset the Canon cartridge? The problem lies in the memory of the chip on the ink tank and printing device. When a new cartridge is installed, the printer reads information from the chip. The software displays the data that the installed ink tank is original and 100% full.

Refillable cartridges do not have such chips, which is why the device cannot read information about a new ink tank and update data in the software. Accordingly, the printing device “thinks” that the cartridge has not been replaced and blocks use. The same situation develops in owners using CISS.

The question of how to reset a Canon cartridge may arise when using an ink tank without chips. Then only the printer’s software cutting and one contact on the cartridge site are responsible for the volume of printed pages and the ink resource. In this case, the ink counter is also reset and you can continue printing.

Let’s take a look at the main ways to reset cartridges in Canon printers, which include the following:

  • Using the programmer;
  • Blocking the read contact;
  • Reset counter in printer.

Each model of printing device has a different zeroing option. Using the wrong method, the user risks damaging the printer, so remember that all actions you perform at your own risk.

The cartridge has a chip: what to do?

How do I reset a Canon cartridge that has a chip? The design of the cartridge does not provide for a chip, but there is a contact pad, which is recognized by the printer, and it reads information about which ink tank is installed and how much it has exhausted its resource.

Optional kit

The most common trick that many people use is to buy two sets of cartridges and print one at a time. Each subsequent ink tank resets information about the previous one. This method has a big disadvantage, which is dangerous for those who rarely print. The ink cartridge is downtime, nozzles dry up and become unusable. If the cartridge is rarely used, go to the instructions and follow the steps in order.

Algorithm of actions

How do I reset a Canon cartridge after refilling? The result is guaranteed by following the instructions sequentially, first for the color cartridge and then for the black one.

Take out the cartridge and cover the top row of contacts with tape or tape.

Install the ink tank in the printer, the message “cartridge not inserted” appears.

Remove the cartridge from the printer.

Cover the second row of contacts with tape (or tape).

A cartridge not inserted error appears again.

Pull the cartridge out again.

Tear off both strips of tape.

Put the ink tank back, the printer will now detect the cartridge as full

After this procedure, you can use them as new. Keep in mind, if the device does not give out a message about an empty cartridge, but simply prints white sheets, then the problem lies in poor-quality refueling or dried nozzles.

How to reset Canon Pixma cartridge

This is a way to disable the printer’s ink counter. Please note that DEACTIVATION is written to the device memory and voids the user of the manufacturer’s warranty. The shutdown procedure is carried out only once and is irreversible.

  • After installing a cartridge refill, an “Ink is running low” error appears. Press ok in the alert window or out of paper. there is paper.
  • If nothing else appears, you can work further.

How to reset a Canon cartridge if an Ink has run out error pops up?

  • You need to click Yes in the window with this notification.
  • A window should appear that says Press and hold the Stop / Reset button, so press and hold the Stop key (or diamond, color copy button. for all-in-one printer, or resume for simple printers) for about ten seconds until the window is NOT disappear.
  • As soon as the message disappears, the printer will reset to zero and start printing.

How to reset a Canon cartridge using the programmer

The safest way to reset the chip is to use a special programmer. There are several types for different nun models. Finding a suitable one is easy, since there are many such offers on the market. They have the same action type:

  • Pulling the cartridge out of the printer.
  • We install it in the programmer so that the chip lies on the contacts.
  • As soon as the indicator light comes on, Take out the ink bottle.
  • Return the cartridge to the printer and print.

Each of the described methods can be considered universal. For newbies, it is recommended to use the programmer zeroing or sealing the ink tank contacts. These options will NOT void your warranty or service. It is worth deactivating the counter if the printer’s warranty period has already expired.

The software component of the Canon MG2440 printer is designed in such a way that it does NOT count the ink used, but the amount of paper used. If the standard cartridge is designed to print 220 sheets, then when this mark is reached, the cartridge will automatically lock. As a result, printing becomes impossible, and a corresponding notification appears on the screen. Restoration of work occurs after resetting the ink level or turning off is notified, and then we will tell you how to do it yourself.

Resetting the ink level of the Canon MG2440 printer

In the screenshot below, you can see one example of low paint warnings. There are several variations of these notifications, the content of which depends on the ink tank used. If you haven’t changed the cartridge for a long time, we advise you to replace it first, and then reset it.

Some warnings have instructions that tell you in detail what to do. If the manual is present, we recommend that you first use it, and in case of its ineffectiveness, it already proceeds to the following actions:

  • Abort printing and then turn off the printer, but leave it connected to the computer.
  • Press the “Cancel” button, which is framed in the form of a circle with triangles inside. Then also press “Enable”.

Hold “Enable” and press 6 times in a row on the “Cancel”.

During pressing, the indicator will change its color several times. The fact that the operation was successful is indicated by a static green glow. Thus, you enter the service mode. It is usually accompanied by an automatic ink level reset. Therefore, then you only need to turn off the printer, disconnect it from the PC and the network, wait a few seconds, and then print again. This time the warning should go away.

If you decide to replace the cartridge first, we advise Pay attention to our next material, in which you will find Detailed instructions on this topic.

In addition, we provide a guide for resetting the diaper of the device in question, which should also be done sometimes. You will find everything you need on the link below.

Disable warning

In most situations, when the notification appears, you can continue printing by pressing the corresponding button, but with frequent use of the equipment, this causes discomfort and takes time. Therefore, if you are sure that the ink tank is full, you can manually turn off the warning in Windows, after which the document will be immediately sent to the printout. This is done like this:

    Open “Start” and go to “Control Panel”.

Find the category “Devices and Printers”.

On your device, right-click and select “Printer Properties”.

In the window that appears, you are interested in the “Service” tab.

There click on the button “Printer Status Information”.

Open the “Options” section.

Scroll down to “Output a warning automatically” and Uncheck “When a low ink warning appears”.

During this procedure, you may encounter the fact that the necessary equipment is missing in the “Devices and Printers” menu. In this case, you will need to manually add it or fix the problem. Expanded on how to do this, read our other article at the link below.

This concludes our article. Above, we described in detail how to reset the ink level in the Canon MG2440 printing device. We hope we helped you to easily cope with the task and you did not have any problems.

Thank the author, share the article on social networks.

It is not uncommon for a situation when, after refilling or replacing cartridges, the printing machine still refuses to print, displaying on the information board and / or screen with a message about the lack of ink in the ink tank. In such cases, the printer needs to “help the understanding” that new cartridges have been installed in it or the installed ones have been refilled. This is done manually by resetting the paint counters. Below we will look at how to perform this procedure on Canon printers.

Diagnostics

Before starting to reset the counters, make sure that there are no following faults:

  • If you have replaced the ink cartridges, make sure to install the correct ink tanks for your printer model. This can be checked in the technical documentation for the printing machines. The user manual must contain information on which models of ink tank to use to work with the existing printer. If the manual was lost, you can download it on the official Canon website (https://www.Canon.Ru) or on NoDevice.
  • If you refilled the cartridges, make sure that the ink missed any electrical contact on the ink tank or carriage itself. Although this usually leads to other kinds of problems, such as “Cartridge Detected”, sometimes there are no ink errors when the surface of the pad is dirty. The same can happen if a foreign object gets stuck between the ink tank and carriage.
  • The device does not display any errors, except messages about the lack of ink in the cartridges. With hardware or software on the front panel of the printing machines or the computer screen, a variety of errors may alternately appear, not in any way related to the Empty ink tank.

If one of the following problems occurs, standard ink reset solutions may NOT work.

Reset cartridge counters

It should be borne in mind that resetting the cartridges does not always mean zeroing the counters built into the ink tank shown. In most cases, the reset procedure involves simply disabling the counters, i.E. The ink level control function is disabled. This leads to the fact that the device does not receive information about the lack of ink in the ink tank, and it continues to “think” of the presence of ink in the cartridges.

It follows from this that the Printing machine will be able to carry out the printing procedure even if there is no ink at all. Running a printhead idle can easily lead to a printhead failure. Therefore, after performing the next reset, users should monitor the level of ink in the ink tank yourself, top up them if necessary.

READ  Printer monitor scanner headphones what is superfluous

To reset (i.E. Turn off) the ink level counter on Canon printers, you can use one of two solutions:

  • Resets ink levels when using front panel buttons on printing machines. This method is also called a hard reset.
  • Using official Canon software or third-party service programs that reset the cartridge counter by sending a command from the computer to the printer. This procedure does not imply the performance of any mechanical operations with the printer itself, therefore it is called a software reset.

Hard reset

Almost every Canon printer allows you to reset the ink levels without the need to use a computer or perform any manipulation of the electronic and mechanical components of the machine. It should also be borne in mind that the procedure for resetting the counters may differ from one Canon printer to another.

For most Canon all-in-one printer models, the procedure for Disabling Ink Level Control can be done as follows:

  • When a message about low ink appears on the computer screen, press the “Stop / Reset” button on the all-in-one printer (the button has a triangle placed in a circle) and hold it for at least 5 seconds. On some printer models, the button needs to be held down longer, but usually no more than 30 seconds.
  • If printing does NOT resume. Turn off the printer for a few minutes, turn it on and try to print the document again.
  • If this does not help either. Turn off the printer (you can simply unplug the power cord from the outlet), press the Stop / Reset button and, Do not release it, turn on the device.

There are more complex procedures for Disabling Paint Meters. For example, for many Canon MP printers (e.G. MP520) and MX printers (e.G. MX310), this is done as follows:

  • Turn off the printer using the off button.
  • Next, you need to enable the service mode of the printer. To do this, press and hold the “Stop / Reset” button, then press the power button and also continue to hold it (ie 2 buttons at the same time). Release the Stop / Reset button and press it twice (the power button must be pressed at this point). Release both buttons. The indicator on the front panel will blink. the printer has entered the service mode of operation.
  • To reset the main counter, it remains to press the “Stop / Reset” button several times, and then once on the power button. If you press “Stop / Reset” 4 times, the main counter will be reset, 5 times. the absorber (“pampers”) counter. Pressing 6 times will reset both counters.

The same procedure for modern Canon Pixma all-in-one printers (e.G. MP520) is performed as follows:

  • Turn off the printer using the power button.
  • Find the following 4 buttons on the control panel: 1) “ON / OFF” or “Power”; 2) button for turning on the black-and-white print mode (images in the form of a diamond with a strip inside) 3) button “OK”; 4) “Stop / Reset” button.
  • Press all 4 buttons at the same time, continuing to hold them for 10-15 seconds.
  • Then release only one power button.
  • The printer will turn on as indicated by the sound of the motors. Ink level control disabled.

Soft reset with native software

If the printer software allows you to turn off ink control, then it is best to use it first rather than third-party applications.

  • Open the “properties” of the printer on your computer. In the case of Windows systems, this is done as follows: go to the “Control Panel”, go to the “Hardware and Sound” section, then. “Devices and Printers”; find the printer in the list of available printers, right-click on its icon and select the “properties” menu item.
  • Go to the “properties” of the printer, find the “maintenance” tab, and in it. “Printer status information”.
  • In a new window. click on the “parameters”.
  • Find the item “Display warning automatically”, next to which the checkbox will be checked.
  • Uncheck the box and click OK or Apply. Paint level control will be disabled.

Not all steps from this instruction (at least, after entering the “properties” of the printer) will correspond to reality. Turning off the ink meter may vary depending on printer model and software version. However, the algorithm of actions is approximately the same in all cases.

Soft reset by third-party programs

There are many utilities created by amateurs, which allow you to reset the ink level at the software level. One of these utilities is MPTool. It successfully clears counters on Canon MP series printers and all-in-one printer.

  • Download and install the program.
  • Turn off the printer, and then turn it on in the service mode, as described in the instructions for resetting the counters of the MP and MX series printers (point “2” in the second instruction of the chapter “hardware reset”).
  • Run the “MPTool” utility. The left side of the program window will display a printer connected to the computer and operating in service mode.
  • On the right side of the window, find the “Operations” section.
  • In the subsection “Ink Counter” there will be two buttons. “Reset Black” and “Reset Color”.
  • Press the “Reset Black” button to reset the black ink cartridges or the “Reset Color” button to reset the color ink tank.
  • Turn the printer off and on during normal operation.
  • Operation completed.

There is another utility, iPTool, which works with many Canon Pixma printers. Its interface almost completely corresponds to that in the “MPTool” program, later you can use the same instruction to reset the cartridges.

How to restart a canon printer after refilling a cartridge

Printer owners are constantly faced with the question: how to reset the Canon cartridge? The problem lies in the memory of the chip on the ink tank and printing device. When a new cartridge is installed, the printer reads information from the chip. The software displays the data that the installed ink tank is original and 100% full.

Refillable cartridges do not have such chips, which is why the device cannot read information about a new ink tank and update data in the software. Accordingly, the printing device “thinks” that the cartridge has not been replaced and blocks use. The same situation develops in owners using CISS.

The question of how to reset a Canon cartridge may arise when using an ink tank without chips. Then only the printer’s software cutting and one contact on the cartridge site are responsible for the volume of printed pages and the ink resource. In this case, the ink counter is also reset and you can continue printing.

Let’s take a look at the main ways to reset cartridges in Canon printers, which include the following:

  • Using the programmer;
  • Blocking the read contact;
  • Reset counter in printer.

Each model of printing device has a different zeroing option. Using the wrong method, the user risks damaging the printer, so remember that all actions you perform at your own risk.

The cartridge has a chip: what to do?

How do I reset a Canon cartridge that has a chip? The design of the cartridge does not provide for a chip, but there is a contact pad, which is recognized by the printer, and it reads information about which ink tank is installed and how much it has exhausted its resource.

Optional kit

The most common trick that many people use is to buy two sets of cartridges and print one at a time. Each subsequent ink tank resets information about the previous one. This method has a big disadvantage, which is dangerous for those who rarely print. The ink cartridge is downtime, nozzles dry up and become unusable. If the cartridge is rarely used, go to the instructions and follow the steps in order.

Algorithm of actions

How do I reset a Canon cartridge after refilling? The result is guaranteed by following the instructions sequentially, first for the color cartridge and then for the black one.

Take out the cartridge and cover the top row of contacts with tape or tape.

Install the ink tank in the printer, the message “cartridge not inserted” appears.

Remove the cartridge from the printer.

Cover the second row of contacts with tape (or tape).

A cartridge not inserted error appears again.

Pull the cartridge out again.

Tear off both strips of tape.

Put the ink tank back, the printer will now detect the cartridge as full

After this procedure, you can use them as new. Keep in mind, if the device does not give out a message about an empty cartridge, but simply prints white sheets, then the problem lies in poor-quality refueling or dried nozzles.

How to reset Canon Pixma cartridge

This is a way to disable the printer’s ink counter. Please note that DEACTIVATION is written to the device memory and voids the user of the manufacturer’s warranty. The shutdown procedure is carried out only once and is irreversible.

  • After installing a cartridge refill, an “Ink is running low” error appears. Press ok in the alert window or out of paper. there is paper.
  • If nothing else appears, you can work further.

How to reset a Canon cartridge if an Ink has run out error pops up?

  • You need to click Yes in the window with this notification.
  • A window should appear that says Press and hold the Stop / Reset button, so press and hold the Stop key (or diamond, color copy button. for all-in-one printer, or resume for simple printers) for about ten seconds until the window is NOT disappear.
  • As soon as the message disappears, the printer will reset to zero and start printing.

How to reset a Canon cartridge using the programmer

The safest way to reset the chip is to use a special programmer. There are several types for different nun models. Finding a suitable one is easy, since there are many such offers on the market. They have the same action type:

  • Pulling the cartridge out of the printer.
  • We install it in the programmer so that the chip lies on the contacts.
  • As soon as the indicator light comes on, Take out the ink bottle.
  • Return the cartridge to the printer and print.

Each of the described methods can be considered universal. For newbies, it is recommended to use the programmer zeroing or sealing the ink tank contacts. These options will NOT void your warranty or service. It is worth deactivating the counter if the printer’s warranty period has already expired.

The software component of the Canon MG2440 printer is designed in such a way that it does NOT count the ink used, but the amount of paper used. If the standard cartridge is designed to print 220 sheets, then when this mark is reached, the cartridge will automatically lock. As a result, printing becomes impossible, and a corresponding notification appears on the screen. Restoration of work occurs after resetting the ink level or turning off is notified, and then we will tell you how to do it yourself.

Resetting the ink level of the Canon MG2440 printer

In the screenshot below, you can see one example of low paint warnings. There are several variations of these notifications, the content of which depends on the ink tank used. If you haven’t changed the cartridge for a long time, we advise you to replace it first, and then reset it.

Some warnings have instructions that tell you in detail what to do. If the manual is present, we recommend that you first use it, and in case of its ineffectiveness, it already proceeds to the following actions:

  • Abort printing and then turn off the printer, but leave it connected to the computer.
  • Press the “Cancel” button, which is framed in the form of a circle with triangles inside. Then also press “Enable”.

Hold “Enable” and press 6 times in a row on the “Cancel”.

During pressing, the indicator will change its color several times. The fact that the operation was successful is indicated by a static green glow. Thus, you enter the service mode. It is usually accompanied by an automatic ink level reset. Therefore, then you only need to turn off the printer, disconnect it from the PC and the network, wait a few seconds, and then print again. This time the warning should go away.

If you decide to replace the cartridge first, we advise Pay attention to our next material, in which you will find Detailed instructions on this topic.

In addition, we provide a guide for resetting the diaper of the device in question, which should also be done sometimes. You will find everything you need on the link below.

Disable warning

In most situations, when the notification appears, you can continue printing by pressing the corresponding button, but with frequent use of the equipment, this causes discomfort and takes time. Therefore, if you are sure that the ink tank is full, you can manually turn off the warning in Windows, after which the document will be immediately sent to the printout. This is done like this:

    Open “Start” and go to “Control Panel”.
READ  How to scan a document with a Samsung printer

Find the category “Devices and Printers”.

On your device, right-click and select “Printer Properties”.

In the window that appears, you are interested in the “Service” tab.

There click on the button “Printer Status Information”.

Open the “Options” section.

Scroll down to “Output a warning automatically” and Uncheck “When a low ink warning appears”.

During this procedure, you may encounter the fact that the necessary equipment is missing in the “Devices and Printers” menu. In this case, you will need to manually add it or fix the problem. Expanded on how to do this, read our other article at the link below.

This concludes our article. Above, we described in detail how to reset the ink level in the Canon MG2440 printing device. We hope we helped you to easily cope with the task and you did not have any problems.

Thank the author, share the article on social networks.

It is not uncommon for a situation when, after refilling or replacing cartridges, the printing machine still refuses to print, displaying on the information board and / or screen with a message about the lack of ink in the ink tank. In such cases, the printer needs to “help the understanding” that new cartridges have been installed in it or the installed ones have been refilled. This is done manually by resetting the paint counters. Below we will look at how to perform this procedure on Canon printers.

Diagnostics

Before starting to reset the counters, make sure that there are no following faults:

  • If you have replaced the ink cartridges, make sure to install the correct ink tanks for your printer model. This can be checked in the technical documentation for the printing machines. The user manual must contain information on which models of ink tank to use to work with the existing printer. If the manual was lost, you can download it on the official Canon website (https://www.Canon.Ru) or on NoDevice.
  • If you refilled the cartridges, make sure that the ink missed any electrical contact on the ink tank or carriage itself. Although this usually leads to other kinds of problems, such as “Cartridge Detected”, sometimes there are no ink errors when the surface of the pad is dirty. The same can happen if a foreign object gets stuck between the ink tank and carriage.
  • The device does not display any errors, except messages about the lack of ink in the cartridges. With hardware or software on the front panel of the printing machines or the computer screen, a variety of errors may alternately appear, not in any way related to the Empty ink tank.

If one of the following problems occurs, standard ink reset solutions may NOT work.

Reset cartridge counters

It should be borne in mind that resetting the cartridges does not always mean zeroing the counters built into the ink tank shown. In most cases, the reset procedure involves simply disabling the counters, i.E. The ink level control function is disabled. This leads to the fact that the device does not receive information about the lack of ink in the ink tank, and it continues to “think” of the presence of ink in the cartridges.

It follows from this that the Printing machine will be able to carry out the printing procedure even if there is no ink at all. Running a printhead idle can easily lead to a printhead failure. Therefore, after performing the next reset, users should monitor the level of ink in the ink tank yourself, top up them if necessary.

To reset (i.E. Turn off) the ink level counter on Canon printers, you can use one of two solutions:

  • Resets ink levels when using front panel buttons on printing machines. This method is also called a hard reset.
  • Using official Canon software or third-party service programs that reset the cartridge counter by sending a command from the computer to the printer. This procedure does not imply the performance of any mechanical operations with the printer itself, therefore it is called a software reset.

Hard reset

Almost every Canon printer allows you to reset the ink levels without the need to use a computer or perform any manipulation of the electronic and mechanical components of the machine. It should also be borne in mind that the procedure for resetting the counters may differ from one Canon printer to another.

For most Canon all-in-one printer models, the procedure for Disabling Ink Level Control can be done as follows:

  • When a message about low ink appears on the computer screen, press the “Stop / Reset” button on the all-in-one printer (the button has a triangle placed in a circle) and hold it for at least 5 seconds. On some printer models, the button needs to be held down longer, but usually no more than 30 seconds.
  • If printing does NOT resume. Turn off the printer for a few minutes, turn it on and try to print the document again.
  • If this does not help either. Turn off the printer (you can simply unplug the power cord from the outlet), press the Stop / Reset button and, Do not release it, turn on the device.

There are more complex procedures for Disabling Paint Meters. For example, for many Canon MP printers (e.G. MP520) and MX printers (e.G. MX310), this is done as follows:

  • Turn off the printer using the off button.
  • Next, you need to enable the service mode of the printer. To do this, press and hold the “Stop / Reset” button, then press the power button and also continue to hold it (ie 2 buttons at the same time). Release the Stop / Reset button and press it twice (the power button must be pressed at this point). Release both buttons. The indicator on the front panel will blink. the printer has entered the service mode of operation.
  • To reset the main counter, it remains to press the “Stop / Reset” button several times, and then once on the power button. If you press “Stop / Reset” 4 times, the main counter will be reset, 5 times. the absorber (“pampers”) counter. Pressing 6 times will reset both counters.

The same procedure for modern Canon Pixma all-in-one printers (e.G. MP520) is performed as follows:

  • Turn off the printer using the power button.
  • Find the following 4 buttons on the control panel: 1) “ON / OFF” or “Power”; 2) button for turning on the black-and-white print mode (images in the form of a diamond with a strip inside) 3) button “OK”; 4) “Stop / Reset” button.
  • Press all 4 buttons at the same time, continuing to hold them for 10-15 seconds.
  • Then release only one power button.
  • The printer will turn on as indicated by the sound of the motors. Ink level control disabled.

Soft reset with native software

If the printer software allows you to turn off ink control, then it is best to use it first rather than third-party applications.

  • Open the “properties” of the printer on your computer. In the case of Windows systems, this is done as follows: go to the “Control Panel”, go to the “Hardware and Sound” section, then. “Devices and Printers”; find the printer in the list of available printers, right-click on its icon and select the “properties” menu item.
  • Go to the “properties” of the printer, find the “maintenance” tab, and in it. “Printer status information”.
  • In a new window. click on the “parameters”.
  • Find the item “Display warning automatically”, next to which the checkbox will be checked.
  • Uncheck the box and click OK or Apply. Paint level control will be disabled.

Not all steps from this instruction (at least, after entering the “properties” of the printer) will correspond to reality. Turning off the ink meter may vary depending on printer model and software version. However, the algorithm of actions is approximately the same in all cases.

Soft reset by third-party programs

There are many utilities created by amateurs, which allow you to reset the ink level at the software level. One of these utilities is MPTool. It successfully clears counters on Canon MP series printers and all-in-one printer.

  • Download and install the program.
  • Turn off the printer, and then turn it on in the service mode, as described in the instructions for resetting the counters of the MP and MX series printers (point “2” in the second instruction of the chapter “hardware reset”).
  • Run the “MPTool” utility. The left side of the program window will display a printer connected to the computer and operating in service mode.
  • On the right side of the window, find the “Operations” section.
  • In the subsection “Ink Counter” there will be two buttons. “Reset Black” and “Reset Color”.
  • Press the “Reset Black” button to reset the black ink cartridges or the “Reset Color” button to reset the color ink tank.
  • Turn the printer off and on during normal operation.
  • Operation completed.

There is another utility, iPTool, which works with many Canon Pixma printers. Its interface almost completely corresponds to that in the “MPTool” program, later you can use the same instruction to reset the cartridges.

How to restart a Canon printer?

Printer failures are common, especially when complex machines are operated by inexperienced office workers or novice users working remotely. It makes sense to emphasize that the peripherals of European, Japanese, American brands are Not the same.

They are similar only in one thing. in purpose, since they perform a function necessary for many, transfer file information to paper. But sometimes any of the printers needs to be overloaded. In this article, we will look at how to reset a Canon printer.

How to reset a cartridge?

This is a problem for Canon cartridge owners. The necessary information is stored in the memory of the built-in chip, and when the user installs a new cartridge, the recorded data is read by the printer. After simple steps, the interface displays information about the percentage of ink refills and other details.

Some cartridge models do not have a microchip. Therefore, the Canon printer may not be able to collect the required information and update the information. The peripheral software of the device is unable to count the data, even if new ink is charged, that is, the level is 100%, and the device locks functions.

To reset the cartridge, you can use one of the following methods:

  • Reset shown counter;
  • Blocking the necessary contacts;
  • Using the programmer.

How to reset an error?

Before printing, you may encounter an unpleasant situation when the computer displays an error message that indicates insufficient ink. Problems are expressed in codes 1688, 1686, 16.83, E16, E13. In addition, the display color will be orange. To get rid of the problem, it is necessary to block the ink level monitoring function in the printing devices.

To resume printing documents, press and hold the Stop / Reset button for 10 seconds. You can use a special application if you want to get rid of the E07 error in MP280 devices. To do this, follow these steps:

  • To install the program;
  • Turn on the printer
  • Press the “Stop” and “Power” buttons simultaneously;
  • Press “Stop” 5 times while holding the second key;
  • Release the buttons;
  • Insert paper and launch the downloaded application.

The last step is to click on the Set button.

How to restart?

There are situations when you need to restart the printer. The most common faults when required are listed below:

  • Jammed paper inside the mechanisms;
  • The printing device does not work;
  • After refilling the cartridge.

If the printing device was working properly and suddenly refused to function, it is possible that a large number of documents have accumulated in the print queue. This problem can be solved without overloading, cleared the Corresponding fields through the interface by opening the “Control Panel”, “Printers”, “View the print queue”, and delete all tasks.

Resetting the print counter

In some cases it will be necessary to reset the counter because the amount of ink is NOT read by the office equipment software. In laser printers, this is done sequentially:

  • Remove the cartridge;
  • Press the sensor with your finger (the button is on the left)
  • Hold until the start of the electric motor;
  • When it works, release the sensor, but after a couple of seconds press and hold again until the engine stops completely;
  • Wait until the device is ready;
  • Insert cartridge.

To reset the refueling of the Canon cartridge you need:

  • Get it out and tape the top row of contacts with tape;
  • Install back and wait for the message “Cartridge not installed”;
  • Remove from the printer;
  • Glue the bottom row of contacts;
  • Will repeat the second and third actions;
  • Remove the tape;
  • Insert back.

The peripheral is now ready for use.

Almost every user can get rid of common mistakes when printing documents, illustrations or restart the printer when it refuses to function. But if he doubts the correctness of his actions, it is better to entrust the difficult work to the specialists of the service center.

The following video describes the process of zeroing cartridges on one of the Canon printer models.

NNCXV.INFO 2021