How To Refill The HP Deskjet 2620 Cartridge

Instructions for refilling cartridges for the HP Deskjet-2130 printer

HP DeskJet-2130 belongs to the budget class of the printer and MFP, with built-in printheads (hereinafter referred to as PG) in the cartridge. When users buy printing devices at a low price, after using up ink, they learn about the cost of new consumables and think about how to save on printing. One way not to spend extra money is refilling HP 2130 cartridges at home.

The printer contains two cartridges, black and color HP 123 cartridges. By their example, we will show you how to refuel the HP DeskJet-2130 printer yourself. For a successful refueling result, you need to make sure that the cartridges are working. The most common problems are a dry printhead or faulty electronics. In the first case, you need to clean the steam generator with a special flushing liquid, and in the second case you need to buy a new one. Refilling the HP DeskJet-2130 cartridge with your own hands is not a difficult process, below we will show how this is possible. In a black cartridge, it is best to insert the needle into the center hole. In Tsvetnoy, first, you need to determine the location of the colors. Several options are possible, one of them is shown in Figure 2.

You can determine the location of colors in different ways:

  • Under the sticker, carefully look at the sponge in the filling holes and see traces of ink.
  • Make a PG print on a sheet (The color in the middle of the print is always at the top, and the colors on the left and right of the print are respectively the print in the cartridge. (Figure 2)).

    • We start refueling the HP 2130 cartridges, we collect paint in the syringes, it is better to take 4 syringes and fill them with ink (Black, Magenta, Yellow, Cyan), you can use 10 or, as in our case, 20 ml. Syringes.
    • Carefully remove the stickers from the top, if you have not done so before.
    • We insert the needle of the syringe into the filling hole. Inserts deeply is not necessary, 10-15 mm is enough. (Figure 3)
    • Inject ink slowly until ink appears in the filling holes, about 3 ml is needed. For black and 9 ml. (3 ml. In each color) for color, then pump the excess ink back into the syringe, always It is better not to add ink than to pour. (Figure 3.)
    • We fill in all colors and Clean the surfaces from ink with a dry napkin.
    • Stick the labels in place (if necessary, you can use scotch tape).
    • We make an imprint with the printheads on the sheet, they must be clear. (Figure 2.)
    • We install the filled cartridges in the printer, we do the cleaning of the steam generator.
    • Pay attention to the contacts (Figure 4), they must be dry, if you install consumables with wet contacts in the printer, your electronics will burn out.
    • If you are refueling for the first time, then you need to cancel Difficult for consumables, to do this, press and hold the Cancel button (red cross or triangle) on the printer for 15 seconds. After canceling tracking, your printing device will signal that the ink has run out, but it will print.

    Instructions for refilling cartridges for the HP Deskjet-2620 printer

    HP Deskjet2620 belongs to the budget class of the printer and MFP, with built-in printheads (hereinafter PG) in the cartridge. When users buy printing devices at a low price, after using up ink, they learn about the cost of new consumables and think about how to save on printing. One of the ways not to spend extra money is to refill HP 2620 cartridges at home.

    The printer contains two cartridges, black and color HP 123 cartridges. By their example, we will show you how to refuel the HP DeskJet-2620 printer yourself. For a successful refueling result, you need to make sure that the cartridges are working. The most common problems are a dry printhead or faulty electronics. In the first case, you need to clean the steam generator with a special flushing liquid, and in the second case you need to buy a new one. Refilling an HP DeskJet2620 cartridge with your own hands is not a complicated process, below we will show how this is possible. In a black cartridge, it is best to insert the needle into the center hole. In Tsvetnoy, first, you need to determine the location of the colors. Several options are possible, one of them is shown in Figure 2.

    You can determine the location of colors in different ways:

    • Under the sticker, carefully look at the sponge in the filling holes and see traces of ink.
    • Make a PG print on a sheet (The color in the middle of the print is always at the top, and the colors on the left and right of the print are respectively the print in the cartridge. (Figure 2)).
    READ  How To Insert Cartridge Into Printer Laser

      • We start refueling the HP 2620 cartridges, we collect paint in the syringes, it is better to take 4 syringes and fill them with ink (Black, Magenta, Yellow, Cyan), you can use 10 or, as in our case, 20 ml. Syringes.
      • Carefully remove the stickers from the top, if you have not done so before.
      • We insert the needle of the syringe into the filling hole. Inserts deeply is not necessary, 10-15 mm is enough. (Figure 3)
      • Inject ink slowly until ink appears in the filling holes, about 3 ml is needed. For black and 9 ml. (3 ml. In each color) for color, then pump the excess ink back into the syringe, always It is better not to add ink than to pour. (Figure 3.)
      • We fill in all colors and Clean the surfaces from ink with a dry napkin.
      • Stick the labels in place (if necessary, you can use scotch tape).
      • We make an imprint with the printheads on the sheet, they must be clear. (Figure 2.)
      • We install the filled cartridges in the printer, we do the cleaning of the steam generator.
      • Pay attention to the contacts (Figure 4), they must be dry, if you install consumables with wet contacts in the printer, your electronics will burn out.
      • If you are refueling for the first time, then you need to cancel Difficult for consumables, to do this, press and hold the Cancel button (red cross or triangle) on the printer for 15 seconds. After canceling tracking, your printing device will signal that the ink has run out, but it will print.

      The need for refueling

      • When white stripes (gaps) began to appear on the leaves
      • The print becomes faint, blurry;

      In order to fill the cartridge with new ink on time, the software (driver) provides a tool for monitoring the ink level for both color and b / w cartridges. At the first sign of running out of capacity, run a check.

      What is needed for refueling

      In addition to ink, you will need:

      Filling of the cartridge HP 123

      • Draw ink into syringes. Draw up about 8-10 ml of black paint, for color compartments draw up 3-4 ml in separate syringes. Place syringes aside. The formation of foam or the ingress of air into the cavity of the syringe is not allowed!
      • Remove the cartridge from the carriage. Open the cover, move the carriage to the center position. Press gently on the top of the container until you hear a click. At this point, the ink tank will change position and you can make a full extraction by pulling.
      • Place a napkin, paper towel or rag folded in several layers on the table so that the ink from the head does NOT smear the work area. Cartridge Place so that the sticker is on top and the nozzles (s) are pressed into the napkin.
      • Use a sharp object (an ordinary knife or a stationery knife) to carefully remove the label from the top. You can NOT completely remove (if they do not interfere), since at the end of the filling, the holes will need to be re-hidden under the sticker.
      • Look in the picture below (arrangement of flowers) and insert the syringe needle 2-3 cm deep into the corresponding holes. The black cartridge has only one hole. There are 5 holes in Tsvetnoy, equal to red and two to yellow / blue. The hole is quite large and needle penetration does not have to be difficult. If the hole is too small, widen it gently with an awl or fine drill.
      • Start filling the container gently and slowly Pressing the plunger of the syringe.
      • When the container is full and the ink starts to protrude the floor of the holes, stop the procedure. Pump the excess ink back into the syringe 1 ml, and wipe the surface of the body well with a napkin so that there are no traces / dirt. Pay special attention to the contacts, if they have ink on them, the computer may NOT see the cartridge after refilling.

      How to refill the HP Deskjet 2130 printer cartridge at home

      The HP 123 cartridge is built into many of the company’s printers. The most popular ones that print from the ink tank of the presented model are: HP Deskjet 2130, 1110, 1115, 2132, 2134, 2135, 2136, 3630, 3635, 3775, 3785, 3830, 3832, 3833, 3834, 3835, 4535, 4675.

      The problem with such printers is the cost of the cartridge, which is commensurate with the printing device itself. So, for cartridge 123, you can give half the cost of equipment. In addition, the volume of the container is too rice. In a refueling state, it will turn out to print approximately 120-150 pages. Then the consumables must either be changed, which is not very convenient due to the high price, or refilled.

      Fortunately, the refillable cartridge (TZK). Therefore, you can refill the HP 123 cartridge yourself at home, rather than resorting to third-party services.

      What ink to fill in HP 123

      The main rule is to purchase only high-quality paints, as the manufacturer’s fame can indicate. From the entire list, we can recommend consumables from Ink Mate (about 650 rubles per 100 ml) and RDM HO series H1W.

      READ  Q2612a Cartridge For Which Printers

      Since the HP 2130 is a color printer, there are two cartridges inside. One is responsible for black and white printing, the second for color. In the latter, the container is divided into three compartments with the same number of holes on the body for refueling inside the cartridge. A certain color is poured into each compartment (more on this below).

      Problems

      • After refueling, the printer may start to print dirty. To avoid this problem, blot the nozzles several times in a tissue paper before placing the ink tank back into the carriage. This removes excess ink from the printheads. Also do a program head cleaning immediately. Try to print any document and make sure the print quality is good.
      • If refilled, the label may wear out and lose its adhesive properties. In this case, duct tape or plaster would be a worthy replacement.
      • Important! In order for air to enter the cartridge, when replacing the sticker, small holes must be made in the places of the filling holes with a needle.
      • The product does not recognize the cartridge. Carefully inspect the cartridge contacts and the circuit board in the carriage. There doesn’t have to be any ink. The presence may result in a lack of contact with the ink tank. If everything is fine, but the indicators on the printer still blink, or the display says “there is a cartridge“, then most likely you will need to buy a new consumable.

      We hope that with such instructions you managed to refill the cartridge for the HP Deskjet 2130 printer and the like. Same technology across many HP inkjet printers.

      How to refill ink in an HP deskjet printer

      The devices of this manufacturer are among the most common, so it is NOT surprising that many users are interested in refilling cartridges for HP. This is not difficult, contrary to popular belief. Any user will be able to self-refuel and get excellent print quality, saving on original consumables. To avoid problems or malfunctions, it is important to follow SIMple rules. First, prepare for refueling:

      • Cover the work surface with paper;
      • Prepare syringes with needles;
      • Open the ink bottles and fill the syringes;
      • Wear gloves to avoid getting your hands dirty.

      It is important that there is a separate syringe for each color of ink, since you cannot mix them with each other. Also try to do everything quickly, since the cartridges can stay outside the printer up to 10 minutes.

      In order to remove the cartridges from the printer, you need to press “Replace cartridge” and wait until the carriage moves to a position that is convenient for removal. The cartridge must be kept with the label facing up and placed on the “filling platform”. a special orange plug on which excess ink will spill and which is convenient for transporting the cartridges. Before refilling an HP cartridge, it is important to make sure the air hole is closed. You need to either glue it with a piece of scotch tape, or cover it with your finger. At the first refueling, it will be covered with a sticker, which will then have to be removed. After opening the filling hole, gently pour a small amount of ink into the HP cartridge so that the foam is completely saturated. After that, you need to close the filling and open the air hole. If this is not done, the printer will print with errors. After that, you need to pull the cartridge out of the plug and blot the excess ink with a napkin.

      Placed the cartridges in the carriage and click, you can continue working. Most of the cartridge models are equipped with chips that reset automatically, and do not require any action from you. If the chips are missing, they can be rearranged from the original cartridges, and they will be reset to zero when removed.

      HP Deskjet-2620 belongs to the budget class of the printer and MFP, with built-in printheads (hereinafter PG) in the cartridge. When users buy printing devices at a low price, after using up ink, they learn about the cost of new consumables and think about how to save on printing. One of the ways not to spend extra money is to refill HP 2620 cartridges at home.

      The printer contains two cartridges, black and color HP 123 cartridges. By their example, we will show you how to refuel the HP DeskJet-2620 printer yourself. For a successful refueling result, you need to make sure that the cartridges are working. The most common problems are a dry printhead or faulty electronics. In the first case, you need to clean the steam generator with a special flushing liquid, and in the second case you need to buy a new one. Refilling an HP DeskJet-2620 cartridge with your own hands is not a complicated process, below we will show how this is possible. In a black cartridge, it is best to insert the needle into the center hole. In Tsvetnoy, first, you need to determine the location of the colors. Several options are possible, one of them is shown in Figure 2.

      READ  Printer To Print From Phone Without A Computer

      You can determine the location of colors in different ways:

      • Under the sticker, carefully look at the sponge in the filling holes and see traces of ink.
      • Make a PG print on a sheet (The color in the middle of the print is always at the top, and the colors on the left and right of the print are respectively the print in the cartridge. (Figure 2)).
      • We start refueling the HP 2620 cartridges, we collect paint in the syringes, it is better to take 4 syringes and fill them with ink (Black, Magenta, Yellow, Cyan), you can use 10 or, as in our case, 20 ml. Syringes.
      • Carefully remove the stickers from the top, if you have not done so before.
      • We insert the needle of the syringe into the filling hole. Inserts deeply is not necessary, 10-15 mm is enough. (Figure 3)
      • Inject ink slowly until ink appears in the filling holes, about 3 ml is needed. For black and 9 ml. (3 ml. In each color) for color, then pump the excess ink back into the syringe, always It is better not to add ink than to pour. (Figure 3.)
      • We fill in all colors and Clean the surfaces from ink with a dry napkin.
      • Stick the labels in place (if necessary, you can use scotch tape).
      • We make an imprint with the printheads on the sheet, they must be clear. (Figure 2.)
      • We install the filled cartridges in the printer, we do the cleaning of the steam generator.
      • Pay attention to the contacts (Figure 4), they must be dry, if you install consumables with wet contacts in the printer, your electronics will burn out.
      • If you are refueling for the first time, then you need to cancel Difficult for consumables, to do this, press and hold the Cancel button (red cross or triangle) on the printer for 15 seconds. After canceling tracking, your printing device will signal that the ink has run out, but it will print.

      Empty cartridges HP 121 (CC640, CC643) and HP 122, HP 650 need to be refilled immediately after the end (both color and black), and better shortly before the end. Refilling a cartridge that has been kept empty for a while is usually a waste of time and money. It is better to refuel using the refueling kit / kit for HP 121 (there is a SIMilar one for 122: black, color).

      Before you start refueling, you should gently clean the outside of the printheads with a damp cloth soaked in cleaning liquid, i.e. Nozzle plate with nozzles on the bottom of the cartridge. And further down the list:

      How To Refill The HP Deskjet 2620 Cartridge
      • Place the cartridge on the tissue with the print head down.
      • Carefully remove the sticker from the cartridge cover.
      • Draw the correct amount of ink into the syringe to refill the HP 121 cartridge, taking care not to draw in air, bubbles and foam.
      • Carefully push the needle deeper into the filling hole of the color you want to fill in (no more than 2-3 cm). Possibly slight resistance of the filler when pushing the needle.
      • Slowly (1 ml. For 15 seconds) inject ink into the cartridge until excess ink appears in the filling holes. Rinse the refill needle with distilled water and dry it before refilling with a different color.
      • Blot the remaining ink around the filling hole to avoid mixing different inks.
      • Cover the top of the cartridge with adhesive tape so that all openings are sealed.
      • Puncture the adhesive tape over the filling holes with a needle.
      • Clean the printhead and cartridge contact plate with a dry cloth.
      • Install the cartridge in the printer and perform the initial check cycle according to the printer’s maintenance manual.

      Attention! HP cartridges No. 121/122, 650 Black are distinguished by the presence of a special camera (indicated by a red rectangle in the photo) of an enlarged size. The new pre-filter separating this chamber and the upper filled space (where refueling takes place) is easily airborne in an empty cartridge and does NOT allow ink to flow to the printheads. As a result, the standard refilling technique with black pigment or water-soluble ink (regardless of manufacturer) often leads to malfunctions.

      As a solution to the airing problem in HP 121 cartridges, air can be pumped out immediately after filling the cartridge using, for example, such a filling platform. As a temporary measure, you can shake the cartridge like a thermometer (nozzles down).

      It is also possible to pierce the pre-filter with a thin syringe needle and “fill” the chamber with ink, but this can lead to unstable cartridge operation. After piercing the pre-filter, ink can flow freely to the print head. To avoid damage to the nozzle plate and SG, do not lower the needle deeper than shown in the photo with the air compartment mark.

      On average, the 121st, 122nd and 650th cartridge withstands from 1 to 5 refills for color and from 1 to 8 for black. The ink tanks are refilled until the electronic part of the cartridge fails (and it burns easily and often).