How to remove balance from the iPhone screen

Eliminating the problem

The first thing to do is to eliminate the possibility of a system failure that prevents the sensor from functioning normally. If the iPhone screen locks intermittently during a call, perform a hard reset. It will help eliminate non-critical errors in the system.

  • Press the Power and Home buttons at the same time.
  • Hold until the Apple logo appears. 9-10 seconds.

IPhone 7 and other models without a physical Home button use a different combination. Power Volume Down key.

iPhone 6 Screen Replacement done in 5 minutes

If the problem is not resolved after a hard reset, perform a factory and content reset. Be sure to back up your iPhone so you don’t lose personal information. After resetting your device, take your time to restore it from a backup. First, set up your iPhone as new, check if the sensor is working, then return the settings and files that were on the phone before the reset.

If factory reset doesn’t solve the problem, take a look at the smartphone screen. Is there a film, glass, or case on it that covers the top of the device? Remove all accessories from the display and test the sensor again. Perhaps a film, glass or case does not allow the waves to pass, and without them the screen will again block perfectly.

When a hard reboot, factory reset, film removal and other measures do not help, there is only one way left. to the service center. Probably something bad happened to the sensor and needs to be replaced. The procedure is quick and inexpensive, but necessary if you want to get rid of your lock screen problems.

Who is responsible for the screen lock

The proximity sensor is responsible for locking the iPhone during a call. The principle of his work is as follows:

  • Waves emanate from an emitter and bounce off a surface. for example, the head to which you bring the phone.
  • The reflected wave hits the receiver, which turns off the display.

It is very simple to check the operation of the proximity sensor: if you cover the part of the phone above the display with your finger when connecting to a subscriber, the screen will turn off. There are no proximity sensor settings on iOS, you cannot turn it off. That is, it either works properly, or does not function due to some kind of error, software or hardware.

Causes of the problem

Among the most common causes of the problem are:

  • Mechanical damage to the proximity sensor due to impact or falling.
  • Poor repair or installation of non-original components.
  • Moisture penetration under glass.
  • Reflection of the sensor signal by protective film or glass.
  • System crash.

Most often, it is possible to detect and fix the problem on its own, but if we are talking about poor-quality repairs and non-original parts or damage due to mechanical stress and water ingress, then you need to contact the service center. In order not to worry about the quality of the repair and the parts used, choose authorized service centers. it will be more expensive, but you will not have to redo everything again.

Important: when the speakerphone is on, the display should not go out. The sensor is triggered only when talking through the speaker.

Enabling iPhone screen lock during a call

The iPhone should be locked during a call automatically as soon as the device is near your ear. Usually there are no errors in the operation of this function, but sometimes users are faced with the fact that the screen is not locked. This leads to accidental call drop, speakerphone on, microphone mute, and other unexpected consequences that interfere with the conversation.

Display stays on after notifications

Another similar problem is that the screen lights up when a notification of a message or other event arrives, and then does not go out. If this happens at night, then by morning you can get a well-discharged smartphone. The problem is unpleasant, but you can solve it yourself, without contacting a service center. For this:

  • Open iOS Settings and go to “General”.
  • Select “Auto-lock”.
  • Set the time interval. By default, the minute should be selected, but you can set it less. The main thing is not to select the “Never” option. it is because of it that the screen does not go out after the notification appears.

If that doesn’t fix the problem, remember when the problem first appeared. Uninstall recent games and applications if you have jailbroken or installed tweaks. pay close attention to them. Jailbreak, by the way, can also be the reason that the proximity sensor stops working on calls, so be careful with system hacks.

If you can’t find a specific app or tweak that is interfering with the normal operation of iOS, perform a hard reboot and reset of settings and content and then set up iPhone as a new device.

What a virtual instrument?

Quite often, this element is launched on newly purchased devices and is used quite actively by many users. Depending on the version of the mobile operating system, this important component has the following functions:

  • withdrawal of the device from the locked mode;
  • performing a quick exit from various applications and games;
  • due to the absence of a physical button on the latest models of iPhones, its virtual analogue is necessary to be able to implement voice control of the device.

But more often it is off. And when you first buy the latest generation iPhone or if a physical key breaks, you need to interact with the software using this very part. So before you study the instructions on how to remove the multitasking button from the iPhone screen, you should familiarize yourself with the algorithm for launching it.

How to display and remove the Home button from the iPhone screen: instructions

Despite the fact that quite often some important elements refuse to work at the right time, the development company has provided some additional tools to help temporarily replace the faulty component. One of them is the virtual Home button.

Further in the material there will be a brief instruction on how to put and how to remove the “Home” button from the screen.

Auxiliary options

When you enter the settings menu of the virtual Home button, you may have noticed that there is an additional list of parameters and settings.

  • single pressing of a virtual key;
  • double tap;
  • long press of the button;
  • element transparency level;
  • customization of the top level of the menu.

All of them help to adapt such tools for comfortable work with the device, and if they are not assigned at least by default, then it will not work to display a substitute for a physical button (although functions are assigned to them all the time).

Now you can go to the main instructions of the article.

How to display a virtual instrument on the screen?

In the latest versions of smartphones from “Cupertinos” the key is not activated. Therefore, in order to correct the situation, it is necessary to use a special service responsible for this button. To start it, you must perform the following sequence of actions:

  • Launch the standard preinstalled “Settings” application on your smartphone.
remove, iphone, screen
  • Then scroll through the list until you find a section called “General”, sometimes “Basic”.
  • Open it and find a subsection called “Accessibility”. Here we go to the main part of the instruction on how to display and how to remove the Home button from the iPhone screen.
  • In the list that opens, find the option called Assistive Touch.
  • Open it.
  • After that, a slider will appear in front of you. Just put it in the state where the green indicator of the switch will be on.
  • Then exit the Settings app on your smartphone’s desktop. The virtual Home button should appear on the screen.

Important! With the active drag-and-drop function, you can place this element anywhere on the screen in which it will be convenient for you.

In order to proceed to the instructions on how to remove the Home button from the iPhone screen, there is one more important point to consider. It deals with the advanced settings of this tool.

How to remove the Home button from the iPhone screen?

It is worth noting that the withdrawal and deletion algorithms are practically no different from each other. Nevertheless, in order to do everything right and not flip through the page several times, it is worth considering the reverse version of the instructions:

  • launch the “Settings” application on your smartphone;
  • scroll through the list of parameters that appears until you reach the line with the signature “Basic / General”;
  • open it and go to the Assistive Touch subsection;
  • here just flip the slider back so the toggle is white.

That’s all, as you can see the instructions on how to remove the “Home” button from the iPhone screen are quite simple and short, so it won’t be difficult for you to remember it.

It is noteworthy that most of the time you have to spend on setting up clicks and menus. But this is already a matter of tastes and preferences.

How to display the Home button on the iPhone screen

Sometimes iPhone and iPad users need a virtual home button. This button is called Assistive Touch. As an accessory to the iOS OS, it often comes to the rescue when the physical Home button or some other button fails.

READ  How to remove auto-lock on iPhone 7

This tool is used in such cases as:

  • The owner of the gadget is a person with disabilities;
  • There is a problem with any button on the case (in most cases, such incidents occur with the Home button);
  • After repairing the physical button, the owner of the iPhone or iPad already uses Assistive Touch out of habit;
  • Some people put a virtual Home button on the screen for convenience, someone prefers to quickly go to the Control Center in this way or use it for a soft reboot of the system, here it is a matter of taste;
  • There are cases when the user uses a virtual button in order to avoid wear and tear on regular buttons.

How to set home button on iPhone screen

Setting up a virtual Home button does not take much time. Follow these guidelines, which include:

remove, iphone, screen
  • Go to the “Settings” menu, then select the “General” item, then go to “Universal Access”;
  • Select the Assistive Touch item and enable the virtual button using the slider, which will turn green;
  • Now the shortcut we need has appeared on the screen, which will allow us to use all the necessary functions. Assistive Touch also allows you to move the button to a convenient location on the iPhone screen.

How do I use Assistive Touch? Which iPhone models support this feature?

The system allows you to customize the home button in versions of iPhone from 3gs up to iPhone X.

When the Home button is activated, you should familiarize yourself with its basic functionality. In rest mode, it is translucent, and when dragged, it becomes noticeably darker, thereby allowing the user not to pay attention to it in moments when there is no need for it.

If you click on Assistive Touch, a window will appear with all its functionality, among which you can select the most necessary.

How to remove the virtual Home button from the iPhone or iPad screen

Sometimes the user of an apple gadget can get confused and instead of disabling this function in the settings menu, he decides to completely reset the settings or is completely flashing iOS. To disable the Home button, you need to take the following simple steps:

  • Go to the “Settings” menu, select the “General” item;
  • We select “Universal access, then” Assistive Touch “, after which we disable this function using the slider, which, when deactivated, will turn gray.
  • From now on, the Home button is missing on the screen of your iPhone.

How to use Assistive Touch?

First of all, you need to place the function menu start button in a convenient place. You can move it along the screen frames by holding it with your finger. You won’t be able to place the key in the center of the screen.

Having decided on the location of the button, click on it. You will see a menu like this:

At the bottom of the menu there is a virtual Home button displayed on the screen. The functionality of the virtual button is 100% consistent with the functionality of the physical one. in particular, a long press on it will launch Siri.

There are other options in the Assistive Touch main menu:

    Notification Center. allows you to call the screen with notifications. The traditional way to bring up this screen is by swiping from top to bottom. Voice control is another way to “wake up” Siri. Control Center. Allows you to display a menu for quick control of some of the iPhone’s functions. Pressing this key actually replaces the bottom-up swipe. Favorites. Through “Favorites”, you can activate gestures that the user has created independently. To start creating a new gesture, go to “Favorites” and click on any of the squares with a “” inside.

Also in the main menu “Assistive Touch” there is a button “Apparatus”. By clicking on it, you will be taken to a submenu, where you will find on-screen keys that allow you to perform actions such as locking / rotating the screen and changing the volume of the device.

With the help of “Assistive Touch” you can even take a picture of the iPhone screen. for this, in the function menu, go along the path “Apparatus”. “” and click on the “Screenshot” button. It is worth photographing only static images in this way, because the on-screen element is triggered with a significant delay.

On devices running iOS 9, the “Assistive Touch” main menu is customizable. In particular, users are able to increase the number of icons in the main menu to 8 pieces.

How to display the Home button on the iPhone screen?

Until the user goes to the workshop to repair the broken Home button, he can control the device using software emulation of this key. The virtual Home button is very convenient and will definitely not fail.

On iPhones, there is only one physical navigation button. the Home button, which is located under the screen in the middle. This key allows you to minimize applications, call the virtual assistant Siri and perform many other necessary actions. It becomes almost impossible to control a gadget without the “Home” button. but what if it is out of order??

Fortunately, Apple has provided the ability to display the Home button on the iPhone screen. You will learn how to do this by reading this article.

How to remove the Home button from the iPhone screen?

Deactivation of the “Assistive Touch” function is performed in the same way as activation. You just need to follow on the iPhone along the path “Settings”. “General”. “Accessibility”. “Assistive Touch” and switch the toggle switch of the same name to the inactive position.

The square with a white circle inside will disappear from the screen.

How to set up quick access to “Assistive Touch”?

You can adjust your iPhone so you don’t have to navigate through the settings to launch Assistive Touch. Here’s how to do it:

Go to the “Accessibility” section in the main settings of the gadget and scroll the screen to the very end. Below you will see the subsection “Keyboard shortcuts”.

In the subsection “Keyboard shortcuts” check the box next to “AssistiveTouch”.

After that, you can call the “Assistive Touch” menu launch button by triple pressing the physical “Home” key and hide it in the same way.

How to enable “Assistive Touch”?

Assistive Touch allows you to display the Home button on the iPhone screen. This function is intended for people with disabilities, however, owners of gadgets with faulty physical keys use it more often.

The Assistive Touch function is especially popular among Chinese users. in the Middle Kingdom, almost half of iPhones are controlled “from the screen”. Practical Chinese argue that this method of control is not only more convenient, but also prevents wear and tear on the physical buttons.

How do you set up Assistive Touch? It is enough to perform a few steps:

Go to “Settings” and follow the path “General”. “Accessibility”.

In the “Accessibility” section, find the “Interaction” block. It will have a subsection “Assistive Touch”. go to it.

Toggle the Assistive Touch slider to the active position.

A translucent square with a white circle inside will appear on the screen. the menu launch button.

This means that the “Assistive Touch” function is activated and you can control the gadget without resorting to physical keys.

“Assistive Touch” can be enabled on any Apple device with iOS version higher than 5.0.

Although the virtual button “Assistive Touch” can completely replace the physical button “Home”, this does not mean that you can wait to repair the device. If the gadget is under warranty, the user should go to the service center immediately. otherwise he risks saying goodbye altogether to the hope of free fixing the defect.

How to turn off touch screen enable on iPhone 11 Pro, iPhone 11, iPhone XS, iPhone XR, and iPhone X

Turning on the screen by double tapping on it has become a popular feature of many Android devices. With its help, it turned out to be possible to quickly activate the device without feeling the power button hidden on the side or top. The iPhone did not initially have such a problem. the device could always be turned on using the Home button. But since the iPhone X, this button has disappeared.

But in return, users were given the ability to activate the display with a simple tap. This made it possible to quickly view notifications on the still locked screen, view widgets and open Control Center.

The Wake up from sleep by touch function turned out to be concise and convenient. Nevertheless, one problem is associated with it. it turned out to be easy to wake up the smartphone with an accidental and unwanted touch. Over time, operating in this mode can lead to an accelerated discharge of the battery. Each time, to turn on the screen, energy is required, and the user may not even suspect about the constant on / off switching of the screen of a device lying, for example, in a bag. But it is possible to disable this function, which will be needed by non-users.

Tap to wake up is exclusive to iPhone 11 Pro, iPhone 11, iPhone XS, iPhone XR, and iPhone X.

READ  Upgrade iPhone to version 10

How to turn off touch screen enable on iPhone 11 Pro, iPhone 11, iPhone XS, iPhone XR, and iPhone X

Go to the “Accessibility” section.

Open the Tap menu and set the Tap to wake up from sleep switch to Off to deactivate this feature.

Now after locking the iPhone, a simple tap on the screen will not activate it.

The use of the device will not change much with the disabling of this function. the iPhone will still automatically turn on the lock screen when the user picks up the smartphone. This feature of devices on iOS is called Raise to Activate (detailed) and is available on any iPhone, starting with iPhone 6s. It can also be turned on or off in the Settings → Display and brightness menu.

Returning the Home Button to the iPhone Screen

Displaying the multitasking button on your iPhone is as easy as removing it.

The sequence is identical and differs only in the last point:

  • “Settings” / “Settings”.
  • “Basic” / “General”.
  • “Accessibility”.
  • Activating the “AssistiveTouch” function.

Accordingly, the button changes from gray to green, indicating that virtual control is displayed on the iPhone screen.

You can make returning the home button even easier. Triple click on the built-in control activates a special menu.

It also has an AssistiveTouch function that takes the user to the desired location in the settings and allows you to turn on “Home” with a single tap.

How to remove the Home button from the iPhone screen

The Home button on Apple tablets and phones has two forms: physical and virtual. If the owner cannot have any influence on the mechanical element, then the graphic analogue can be displayed and removed from the screen at any time.

A simple and understandable step-by-step instruction in our article will allow you to quickly remove the Home button from the iPhone screen, and she will also teach you how to activate the Home function again.

To remove the virtual “Home” button, you need to go to the settings and follow a simple path:

  • “Settings” / “Settings”.
  • “Basic” / “General”.
  • “Accessibility”.
  • Deactivating the “AssistiveTouch” function.

The fact that the Home button is disabled will be indicated by a change in color indication: green ON turns into gray OFF.

The need to remove the “Home” button is more rare; users of Apple products, on the contrary, tend to bring virtual controls to the screen.

Many people consider it necessary to activate the graphic option “Home” as a preventive measure. After all, the less often you press the standard version of the Home button, the longer the iPhone lives without repairing and replacing the physical button.

Additional functions of the Home button

Home is a multi-tasking key. In fact, this is another menu for quickly managing iPhone services.

Everyone knows its standard use cases:

  • Single press. return to the main menu.
  • Double tap. open multitasking.
  • Triple press. call additional features.

Additional features can also be enabled or disabled in the “Accessibility” in the settings by ticking the desired options in the “Keyboard shortcuts”.

The Best way How To Remove iPhone Screen without a Suction cup 6 6s 6s plus

What can be set or deactivated in this miniature dedicated menu?

  • “Color inversion”. Change all screen shades to the opposite, which is convenient for adapting the device for reading at night.
  • “Increase”. An excellent magnifier for visually impaired users, as well as a convenient way to view small pictures on the Internet.
  • AssistiveTouch. Quick call of the “home” button and its instant deactivation.
  • “SwitchControl”. Adaptation of iPhone controls for the limited capabilities of some users. With the correct setting of the “switches”, you can adjust the operation of the phone services by head movements, single touch or via Bluetooth.
  • “Shades of Gray”. Converting the product to black and white mode to save energy or just like that.

Any of the named functions can be connected or removed, but it will not work to add new tasks to this list. And why? IPhones are the perfect user technique that gives the most to everyone.

The only thing the owner needs to do is to master all the possibilities of an ultra-modern smartphone and use them 100%.

How to press the Home button on the iPhone screen

Now, a few words about how to press the Home button using the iPhone screen. To do this, you need to click on the floating button of the “Assistive Touch” function. As a result, a menu of several items should appear on the screen. Among other things, there will be a Home button. Click on it and your iPhone will react as if you pressed a hardware button on the body of the device.

If suddenly your menu does not have a Home button, then return to iPhone Settings and open the section “General. Accessibility. Assistive Touch. Top Level Menu”.

remove, iphone, screen

Here you can customize which options are available in the Assistive Touch menu. To add a Home button, click on any of the available options.

And in the list that opens, select the “Home” button.

Here you can also reset the “Assistive Touch” settings or increase the number of available options.

How to remove the Home button from the iPhone screen

The Home button on Apple tablets and phones has two forms: physical and virtual. If the owner cannot have any influence on the mechanical element, then the graphic analogue can be displayed and removed from the screen at any time.

A simple and understandable step-by-step instruction in our article will allow you to quickly remove the Home button from the iPhone screen, and she will also teach you how to activate the Home function again.

To remove the virtual “Home” button, you need to go to the settings and follow a simple path:

  • “Settings” / “Settings”.
  • “Basic” / “General”.
  • “Accessibility”.
  • Deactivating the “AssistiveTouch” function.

The fact that the Home button is disabled will be indicated by a change in color indication: green ON turns into gray OFF.

The need to remove the “Home” button is more rare; users of Apple products, on the contrary, tend to bring virtual controls to the screen.

Many people consider it necessary to activate the graphic option “Home” as a preventive measure. After all, the less often you press the standard version of the Home button, the longer the iPhone lives without repairing and replacing the physical button.

How to display the Home button on the iPhone screen

The breakdown of the Home button is not a common phenomenon, however, when this happens, the user is practically deprived of the opportunity to fully use his iPhone. Indeed, without this button, it is impossible to return to the home screen, close applications, switch between running applications and perform many other operations.

The surest solution in such a situation is to contact the service center. But, there is not always time and money to repair your favorite gadget. Sometimes you need a phone right now, but it doesn’t actually work. In such a case, there is a temporary solution. You can bring the Home button to the iPhone screen and press it using the touchscreen.

You can use this method on any iPhone model that has been updated to iOS 5 or higher. And these are such models as iPhone 4, 4s, 5, 5s, 6, 6s, 7, 8 and iPhone X.

How to display a virtual instrument on the screen?

In the latest versions of smartphones from “Cupertinos” the key is not activated. Therefore, in order to correct the situation, it is necessary to use a special service responsible for this button. To start it, you must perform the following sequence of actions:

  • Launch the standard preinstalled application “Settings” on your smartphone.
  • Then scroll through the list until you find a section called “General”, sometimes “Basic”.
  • Open it and find a subsection called “Accessibility”. Here we go to the main part of the instruction on how to display and how to remove the Home button from the iPhone screen.
  • In the list that opens, find the option called Assistive Touch.
  • Open it.
  • After that, a slider will appear in front of you. Just put it in the state where the green indicator of the switch will be on.
  • Then exit the Settings app on your smartphone desktop. The virtual Home button should appear on the screen.

Important! With the active drag-and-drop function, you can place this element anywhere on the screen in which it will be convenient for you.

In order to proceed to the instructions on how to remove the Home button from the iPhone screen, there is one more important point to consider. It deals with the advanced settings of this tool.

Using AssistiveTouch instead of multi-finger gestures

After selection, several dots will appear on the screen, indicating where the virtual fingers touched the screen. Moving one finger across the screen or making taps will control all virtual fingers at once. After a few seconds of inactivity, virtual fingers will automatically disappear.

Auxiliary options

When you enter the settings menu of the virtual Home button, you may have noticed that there is an additional list of parameters and settings.

  • single pressing of a virtual key;
  • double tap;
  • long press of the button;
  • element transparency level;
  • customization of the top level of the menu.

All of them help to adapt such tools for comfortable work with the device, and if they are not assigned at least by default, then it will not work to display a substitute for a physical button (although functions are assigned to them all the time).

READ  How to change icons on iPhone

Now you can go to the main instructions of the article.

Output on display

Initially, the Home button for Apple gadgets is not displayed. In order for it to appear on the display, you must resort to the help of a specialized service. It is included in standard iOS apps.

The AssistiveTouch service is responsible for displaying the Home button on the screen. It is on every modern “apple” phone or tablet. It is with its help that you can figure out how to remove the Home button from the iPhone screen.

It is proposed to display Home on the display as follows:

  • Open “Settings” on iPhone.
  • Go to “General / Basic”. “Accessibility”.
  • Select the AssistiveTouch menu item.
  • Move the slider so that the green area next to it lights up.

You can exit the smartphone settings. After the done actions, a graphic interpretation of the Home button will appear on the screen. It can be placed in any convenient place and used as intended instead of the physical control mounted in the gadget.

Removing a button

In fact, there is nothing difficult about displaying Home. How do I remove the Home button from the iPhone screen? Every owner of an “apple” phone is capable of doing this.

Reset Appstore Balance to 0.00 | Clear Appstore balance to change country

It is easy to guess that, in general, enabling and disabling the option under study is done in approximately the same way. Accordingly, you will need to work with AssistiveTouch.

To get rid of the Home button on the display, you need to:

  • Turn on iPhone.
  • Go to the menu “Settings”. “General”.
  • Click on “Accessibility”.AssistiveTouch.
  • Flip the switch to the “Off” position. At the same time, the green indicator should disappear next to it. It usually turns white.

This is where all the actions end. You can exit the settings and continue working with your mobile phone without the Home button on the display.

How to remove the Home button from the iPhone screen. All About the Home Button

The iPhone is the iconic smartphone of the current generation. These phones are in great demand among the population around the world. But you need to be able to handle this gadget. The Home button plays a huge role in device control. Sometimes she refuses to work or starts to “glitch”. At such moments, you can display the faulty element on the screen and use a graphic interpretation instead of a physical one. It is very convenient. Especially if there is a suspicion of a device breakdown. Next, I’ll show you how to remove the Home button from the iPhone screen and bring it up to the display. Anyone can cope with the tasks!

About the Home button

But first, a little about the mentioned control. Why is the Home button needed? And does it really need to be displayed and removed from it?

The Home button is used very actively. This is one of the most useful smartphone controls from Apple. The button has a huge number of uses. They mainly depend on the operating system used.

  • unlocking a mobile phone;
  • quick exit from programs, applications or games;
  • voice control of the device (especially in the latest iOS).

How to remove the Home button from the screen of iPhone 4 or any other if necessary? What needs to be done to initially display it on the display? This will be discussed further.

On this note, it is proposed to end. From now on, it is clear how to remove the “Home” button from the screen of an iPhone 5 or any other “apple” device.

All modern devices from Apple have AssistiveTouch. It is with its help that the “Home” button on the display is displayed and configured. Every iPhone owner is able to understand the work of this service in a few minutes.

Together with the Home button, the following options are displayed:

  • notification center;
  • device functions;
  • Siri;
  • “User”.

It is noted that without them, displaying “Home” on the screen will not work. In the same way as removing from the display. Perhaps this is all that can be said about displaying a control called Home on the screen and removing it from there.

Blue tint

A defect indicates a poor-quality contact of the connector and / or loop. If the stripes flicker and the screen on iPhone 5s or later is severely buggy, it may indicate an unstable signal.

The main reasons for the appearance of stripes

Whitish or colored stripes on the latest iPhone series may indicate:

  • breakdown of the phone’s sensor chip;
  • physical malfunction of the display. To solve the problem of broken or cracked glass, just change the screen to a new (original) one;
  • penetration of moisture into the interior: corrosion, closing / opening of contacts, failure of a loop, etc. Water, tea or a carbonated drink are most “terrible” when the smartphone is turned on. they can lead to failure of microcircuits, printed circuit board, etc.
  • breakdown of the smartphone loop;
  • incorrect firmware and software updates. IPhone may have a black display with no signs of life when turned on;
  • mechanical damage to the elements of the printed circuit board;
  • malfunction of the connector for the loop.

Apple devices iPhone 6 and 5 series are considered especially sensitive to mechanical stress. In this case, the phone does not have to be thrown against the wall or dropped on the asphalt. It is enough to carry it in your trouser or just toss it into your bag. The case of Apple’s gadgets of the latest series is made using a special technology. one-piece cast. But this does not guarantee that prolonged squeezing and slight bending will pass without consequences. Therefore, if you find vertical stripes on the iPhone 5s or 6 models, it is wiser not to make serious attempts to repair yourself.

How to get rid of stains?

If the screen of the device has gone out or a flaw has appeared on it, do not panic and immediately run to the service center. There are problems you can try to fix yourself. The main thing is not to repair it. When detecting color or white defects, proceed as follows:

  • Reboot the smartphone. After switching off, let the technique “rest” for 2-3 minutes before switching it on again.
  • Check the train. A black screen of the device may also be a sign of a loose loop. It is necessary to carefully disassemble the case and install it “all the way”.
  • Reset iPhone to “Default” settings. Reset updates or uninstall those applications that were installed before the stripes appeared. Reboot.
  • Update device software. Go to “Settings”, click the menu item “Updates”. Then follow the instructions strictly. Reboot device.
  • Dry the equipment. If the phone falls to the input, you need to quickly get it out, gently wipe the case with a dry soft cloth and turn it off. Let it rest for 3-5 days. Then try turning it on. Long-term presence of equipment in water requires its complete disassembly and professional drying of contacts and microcircuits.

IPhone screen stripes after a fall. what to do?

Even the reliable, functional and resistant to the harsh operating conditions of the iPhone, the Apple trademark, with careless and careless use, will cease to work stably and efficiently. This often happens after the smartphone has been dropped on a hard surface, severe mechanical impact, or moisture ingress. The consequences of inaccurate operation can be very different. the phone is dull and often requires a reboot, the sensor refuses to work, the device does not respond well to commands, etc.

But more often, the results of a fall are invisible at first and are manifested by vertical streaks, after a few days of operation. What action should I take if my smartphone is dropped on a hard surface or in water, for example? What should I do if the screen goes out and does not turn on, vertical streaks appear on it? We will answer all the burning questions in this article, we will analyze each case separately.

Horizontal stripes

In addition to vertical defects, it is not uncommon for iPhone 5s and 6 to have horizontal (blinking, flickering, solid, or colored) streaks. This signals a serious problem with the monitor. If horizontal flaws are detected, the user may notice that the sensor does not work or has become poorly sensitive.

The effects of falling or crushing, mechanical stress or moisture can be expressed in more than just visible flaws on the display. Slight bends and light bumps in the center of the smartphone monitor in 87% of cases lead to physical damage. Only a professional can fix a broken iPhone display module by replacing it with a new one.

Gray tint

The defect appears at the bottom of the monitor and can cover ½ part of it. The problem only occurs on early iPhones.

NNCXV.INFO 2021