How To Remove Margins When Printing On A Printer

Configuring Borderless Printing

Choose borderless printing.

Select Borderless from the Page Layout list on the Page Setup tab.

When the confirmation message appears, click OK. When prompted to change the media type, select the media type from the list and click OK.

Check the paper size.

Check the Page Size list. To change the settings, select a different page size from the list. The list only shows sizes that can be used for borderless printing.

Adjust the amount of expansion for the paper.

If necessary Change the amount of expansion using the Amount of Extension slider. Moving the slider to the right increases the amount of paper expansion, and moving the slider to the left decreases the expansion. In most cases it is recommended to set the regulator to the second position.

If the Amount of Extension slider is set to the far right, ink drips may appear on the back of the paper.

Click OK. When you execute print, the data will be printed without any margins on the paper.

If you select a page size that cannot be used for borderless printing, then the size is automatically selected from among those allowed for this type of printing.

If the Borderless check box is selected. The Printer Paper Size settings. Duplex Printing. Stapling Side. And also the Stamp / Background button. (Stamp / Background.) Are grayed out and locked on the Page Setup tab.

When Envelope is selected on the Main tab. High Resolution Paper or T-Shirt Transfers for Media Type. Borderless printing cannot be performed.

Depending on the type of media used for borderless printing, print quality may deteriorate in the top and bottom areas of the letter, or smudges may appear.

If the ratio of height to width differs from the corresponding ratio for the image, part of the image may be lost when printed on some sizes. In this case, crop the image to fit the paper using your software application.

When Plain Paper is selected on the Main tab of Media Type. Borderless printing is not recommended. Therefore, a message appears to select the media. If you are using plain paper for Proof Print, select Plain Paper and click the OK button.

Performing borderless printing

Borderless printing function allows you to print without leaving borders. This is achieved by enlarging the document to be slightly larger than the paper. In standard printing, margins are created around the document area. However, when using the borderless printing function, these margins are created. To print a document (such as a photo) without borders around the image, set it to Borderless Print.

Borderless printing is performed as follows.

Borderless printing can also be set in the Additional Features settings of the Quick Setup tab.

To enlarge the printable portion of the document

By setting a large expansion ratio, you can perform borderless printing rather than experiencing difficulty. However, the part of the document that extends beyond the paper will not be printed and for this reason, some part of the photo around its perimeter may not fit onto the paper.

Perform a borderless test print. If you are not satisfied with the result of borderless printing, reduce the expansion ratio. The Amount of Extension decreases as you move the slider to the left.

If the expansion ratio is reduced, unwanted margins may remain when printing on some paper sizes.

If the Amount of Extension slider is set to the far left, images will be printed at full size. When this option is set to print the address side of a postcard, the sender’s zip code is printed in the correct location.

When Preview before printing is checked on the Main tab. Before printing, you can check if the paper will actually have NO margins.

Change margins in Word

You are less likely to print a borderless page from a word processor, but if you ever need to, the settings are SIMple. Microsoft Word usually sets a default margin of one inch along the entire length of the document. You can change the settings to increase or decrease the amount of white space on the page, or even offset the entire page to provide some kind of anchoring along one edge. In this case, your goal. Remove the margins entirely, so click Layout, then Margins, and finally Custom Margins Change the margins for the top, bottom, and sides to zero Other Office apps and word processing programs from other vendors Should work SIMilarly, although the exact names of the menu items may vary.

How to remove page numbering when printing on a printer

Change margins in Acrobat

Adobe Acrobat software. Another widely used graphics program because the PDF files it generates should look and print the same across multiple devices and printers. The easiest way to print full-page images is in Acrobat. Choose a paper size that is identical to your image or slightly larger. Click “File” and then “Print” to open the Print Dialog Box, and then click the “Size” button. Under “Size” select “Actual Size” and then “Print”.

Setting margins in Photoshop

Photoshop is commonly used by graphics professionals, so it has more. And harder! Print settings than most programs. Most of them are related to image quality and resolution, so you do not need to deal with them in this case. Start by selecting “File”, then “Print” and clicking on the “Position and Size” settings. Usually the default setting. Scale to Fit Media, which is Printed in page margins. Deselect, then manually enter Scale, Height, and Width values ​​equal to the full size of your paper. Click “Print” to print the image. This should work for any small print run you do in-house, but if you are preparing an image as “camera-ready” art for an external printer, it is usually best to print on paper larger than your final image, so the printer can handle lines trims to align.

Changing fields in Google Docs

If you’re using Google Docs as a cross-platform text editor, you can also set it up for borderless printing. From the File menu, choose Page Setup, and then set all fields to zero. Your document will be printed across the full width of the paper if your printer settings are SIMilar.

Setting up the printer

Even if all the settings in the document itself are correct, you may still find that your document does not Print without Borders, usually because there are default borders for each document in the printer driver, and as long as they are NOT will be resized, your document will be framed, or your program will tell you that you are trying to print a document that is too large for the page. To fix this, open Devices and Printers from the start menu, then Right-click your printer icon. Choose Print Settings from the pop-up menu, then VIEW the setting options provided by your print driver. This is usually called “Layout” or “Page Layout”. “After you clicked Layout, you should be able to manually set the margins to zero. For some printers, you may need to dig another layer and find the Advanced Setup screen to navigate to those settings. Newer printers, especially those focused on photography, MUST have an explicit setting for borderless printing. Click on it and then click “Print” to finish printing the document.

Disable PRINT

In Firefox web browser. To change the print settings, go to the menu “Firefox”. “Print.”. “Page settings.”.

In the window that opens, go to the “Fields and headers and footers” tab.

In the section “Headers and footers” in all positions, select the value “-blank-” and press the “OK” button.

Disable printing in Google Chrome web browser. In the settings menu or by clicking in the browser window with the right mouse button, select the “Print.”.

In the next window, uncheck “Headers and Footers”, while in the preview window we will see how the printed page will look.

READ  Printer Does Not Work On Windows 10

In the Opera web browser. In the browser menu “Opera” go to “Print”. “Print settings.”.

In the window that opens, uncheck the “Print headers and footers” item and click on the “OK” button.

In the Internet Explorer browser. Press the arrow on the button with the printer and click on “Page settings.”.

In the section “Headers and footers” in all positions, select the value “-Blank-“.

Unfortunately, I did not find how to set these default print settings in Internet Explorer, so when using it, you have to do this operation constantly. Thank you for attention!

How To Delete Copies Of The Same Printer | Small Business

When you reinstall the printer, you may receive multiple copies of the same printer, listed in the Devices and Printers window, and available for use in program print jobs. It can also happen after Windows 7 automatically installs Updated Drivers. Removing THESE additional copies avoids confusion among employees who need to print documents for your business. However, before deleting copies, make sure the original version works.

Setting page margins

Select Page Layout Fields Custom Fields.

In the Margin Guides box, enter minimum margins for the printer, or specify margins that exceed the unprintable area of ​​the printer.

HP Designjet printers. Change Print Settings (Windows 10)

Selecting Best produces the best print quality at the slowest print speed. The Normal setting increases the print speed but decreases the quality. The Fast option prints at the fastest speed.

You can select print quality from the standard settings by switching between Speed ​​and Quality. Alternatively, it can be changed in the Custom Options Settings section.

Paper type

The value Automatic is selected by default. When set to this value, the printer automatically selects the paper type. You can also select the paper type from the drop-down list.

Document size

Select the paper size from the drop-down list.

Click Custom to create or modify custom paper size information.

Fields

Standard.

Printable area is equal to the selected paper size minus the selected margins.

The printer will add the selected margins to the printable area and align the resulting size to the edge of the loaded paper.

The printer will cut the paper to fit the selected paper size.

Increased.

Printable area is equal to the selected paper size.

The printer will add margins to the printable area and align the resulting size with the edge of the loaded paper.

Printer will cut paper to fit the selected paper size, adding printer margins.

Crop content to fit field.

Printable area is equal to the selected paper size.

The printer will align the selected paper size to the edge of the loaded paper, then trim the content to the selected margins. The product will not print in the cropped area.

The printer will cut the paper to fit the selected paper size.

Pages per sheet

Select the number of pages to be printed on each sheet of paper.

Disable automatic cutter

Select to disable automatic cutter to prevent the machine from cutting the page after a print job.

Eliminate gaps or remove top and bottom gaps

Select to use only the roll paper required to print the image, which will save paper. If you select this option, the product will not print blank areas in the image. On second printer models, this setting is called “Ink area”

Cut lines

Select this option to print crop lines on the page.

Remove margins between pages

When enabled, multi-page print jobs will be printed without top and bottom margins as a single continuous image.

Automatic rotation

Select this function to enable automatic rotation of an image or document to save paper or prevent cropping.

Page order

Specifies the order in which the pages of the document are printed.

First page on top. Printing the document with page 1 on top of the stack.

Last page on top. Prints the document with page 1 at the bottom of the stack.

Delivery

Hold to print manually with stacker open

Manual Printing with Stacker Open

To prevent stacker wheel marks on some types of photo paper, you can print jobs from the front of the printer with the stacker cover open.

To print a job manually, Click Print in your application, add the job to the printer’s job queue (if available), then follow the front panel instructions.

Show preview before printing

Includes the Print Preview utility to display the layout of the document immediately before starting a print job. To print the job, click the “Continue” button in the preview window.

Change of size

Actual size. This will print the document without resizing.

To size. This option will print the document on a different paper size than the document was formatted for.

This option is useful in cases where the document is formatted for a currently unavailable paper size. For example, a document was formatted for Letter size paper, but you have that paper size and you can print the document on a different paper size.

Fit to Fit Not available if Pages Per Sheet or Pages Per Sheet Poster is set to more than one.

% Of actual size. Click to enlarge or reduce the document to normal size. Only the image size is changed, your document Prints on the paper size selected in the application. Enlarging the document may crop some portion of each page.

Quick settings

The print driver provides a variety of options that you can change when printing a job. Speed ​​dial saves the value for the print job so that you can set these values ​​with one click. Some settings (for example, paper size, paper source, and orientation) can be overridden by values ​​specified in the application.

To create a customized speed dial, follow these steps:

Choose the speed dial that best suits your needs.

Change any values ​​on any other tabs.

Save the new speed dial with a name of your choice.

Click the Factory Defaults speed dial to restore all parameters to their default values.

Color options

Select the print option Grayscale or Black Only.

Color management

The application controls the colors. Allow the program in which you are printing to control the color of the document.

The colors are controlled by the printer. Let the printer control the rendering intent and select source profile

Printer emulation

Select the printer whose colors you would like to emulate

HP Deskjet 2600 printers. Resolving poor print quality

If your printouts have text defects or blur, clean the entire area around the ink nozzles.

You will need the following materials:

A clean, lint-free, or dry cotton swab

Distilled or bottled water

DO NOT use tap water as it may contain contaminants that can damage the printhead.

Open the cartridge access door.

The carriage will move to the center of the printer.

Wait for the carriage to come to a complete stop before continuing.

Press down lightly on one of the ink cartridges to release it, then pull the ink cartridge out of the slot.

DO NOT remove both cartridges at the same time. Remove and clean the cartridges one at a time. Do not leave removed ink cartridges for more than 30 minutes.

Grasp the sides of the cartridge.

Lightly dampen a clean, lint-free cloth or swab in bottled or distilled water.

Wipe the front and edges around the ink nozzle with a cloth or swab.

DO NOT touch the nozzle plate.

Nozzle plate. does not clean

Area around the ink nozzles. Cleaning required

Ink cartridge contacts. does not clean

Wait 10 minutes for the cleaned area to dry before continuing.

Hold the sides of the ink cartridge with the tabs facing the printer, insert it into the slot, then gently push the cartridge until it clicks into place.

Repeat these steps to clean the nozzle area on a different ink cartridge.

Close the cartridge door.

Try to print. If the print quality is still not acceptable, go to the next step.

HP Designjet printers. Change Print Settings (Windows 10)

Print quality

Selecting Best produces the best print quality at the slowest print speed. The Normal setting increases the print speed but decreases the quality. The Fast option prints at the fastest speed.

You can select print quality from the standard settings by switching between Speed ​​and Quality. Alternatively, it can be changed in the Custom Options Settings section.

Paper type

The value Automatic is selected by default. When set to this value, the printer automatically selects the paper type. You can also select the paper type from the drop-down list.

Document size

Select the paper size from the drop-down list.

Click Custom to create or modify custom paper size information.

Fields

Standard.

Printable area is equal to the selected paper size minus the selected margins.

The printer will add the selected margins to the printable area and align the resulting size to the edge of the loaded paper.

READ  Printer Failed To Print Windows 10

The printer will cut the paper to fit the selected paper size.

Increased.

Printable area is equal to the selected paper size.

The printer will add margins to the printable area and align the resulting size with the edge of the loaded paper.

Printer will cut paper to fit the selected paper size, adding printer margins.

Crop content to fit field.

Printable area is equal to the selected paper size.

The printer will align the selected paper size to the edge of the loaded paper, then trim the content to the selected margins. The product will not print in the cropped area.

The printer will cut the paper to fit the selected paper size.

Pages per sheet

Select the number of pages to be printed on each sheet of paper.

Disable automatic cutter

Select to disable automatic cutter to prevent the machine from cutting the page after a print job.

Eliminate gaps or remove top and bottom gaps

Select to use only the roll paper required to print the image, which will save paper. If you select this option, the product will not print blank areas in the image. On second printer models, this setting is called “Ink area”

Cut lines

Select this option to print crop lines on the page.

Remove margins between pages

When enabled, multi-page print jobs will be printed without top and bottom margins as a single continuous image.

Automatic rotation

Select this function to enable automatic rotation of an image or document to save paper or prevent cropping.

Page order

Specifies the order in which the pages of the document are printed.

First page on top. Printing the document with page 1 on top of the stack.

Last page on top. Prints the document with page 1 at the bottom of the stack.

Delivery

Hold to print manually with stacker open

Manual Printing with Stacker Open

To prevent stacker wheel marks on some types of photo paper, you can print jobs from the front of the printer with the stacker cover open.

To print a job manually, Click Print in your application, add the job to the printer’s job queue (if available), then follow the front panel instructions.

Show preview before printing

Includes the Print Preview utility to display the layout of the document immediately before starting a print job. To print the job, click the “Continue” button in the preview window.

Change of size

Actual size. This will print the document without resizing.

To size. This option will print the document on a different paper size than the document was formatted for.

This option is useful in cases where the document is formatted for a currently unavailable paper size. For example, a document was formatted for Letter size paper, but you have that paper size and you can print the document on a different paper size.

Fit to Fit Not available if Pages Per Sheet or Pages Per Sheet Poster is set to more than one.

% Of actual size. Click to enlarge or reduce the document to normal size. Only the image size is changed, your document Prints on the paper size selected in the application. Enlarging the document may crop some portion of each page.

Quick settings

The print driver provides a variety of options that you can change when printing a job. Speed ​​dial saves the value for the print job so that you can set these values ​​with one click. Some settings (for example, paper size, paper source, and orientation) can be overridden by values ​​specified in the application.

To create a customized speed dial, follow these steps:

Choose the speed dial that best suits your needs.

Change any values ​​on any other tabs.

Save the new speed dial with a name of your choice.

Click the Factory Defaults speed dial to restore all parameters to their default values.

Color options

Select the print option Grayscale or Black Only

Color management

The application controls the colors. Allow the program in which you are printing to control the color of the document.

The colors are controlled by the printer. Let the printer control the rendering intent and select source profile

Printer emulation

Select the printer whose colors you would like to emulate

Setting page margins for printing with Publisher

Most printers DO NOT print in the margin of the paper (up to about 13 mm from the edge of the page). You can find out the size of the unprintable area of ​​your printer on the File tab in the Print section.

Select File Print to open the print page in Backstage view.

Under Printers, click the arrow to select a printer.

Let’s point to a small information icon, and below the Printable area, the minimum margins for printing on the left and top of the page will be displayed.

Be aware of minimum printer margins when following these steps to set publish margins.

How To Remove Margins When Printing On A Printer

Borderless printing and copying HP laserjet printer HP LaserJet M1319 Multifunction Printer series

Adjusting the contrast for the current job

To view the current contrast value on the control panel, press the button

Change the parameter using the arrows. Move the slider to the left to make a copy lighter than the original or to the right to make a copy darker than the original.

Press to save the selection and immediately start the copy job.

Press the button to save the selection without starting the job.

Changing this parameter will be valid for about

Two minutes after the copy job completes. At this time, the User settings line will be displayed on the device control panel.

Change the default contrast

The default brightness setting affects all copy jobs.

On the control panel, press

Use to select CUSTOM. COPY, then press

Use to select Default Contrast, then press

Change the parameter using the arrows. Move the slider to the left to make all copies lighter than the original or to the right to get all copies darker than the original.

To save data.

Change the print density when copying

Increasing the print density on the product control panel darkens the printed pages.

On the control panel, press

Use to select CUSTOM. SYSTEMS, then press

Use the arrows to select Next. Paper, then press

Use the arrows to select Print Density, and then press

Use the arrows to Increase or Decrease the density and press

Set custom copy options

When you change copy settings using the control panel, Custom Settings appears. The user parameters are valid for about 2 minutes, after which the device returns to the default parameters. To return to the default settings immediately, press

Borderless printing and copying

The device cannot print, do not leave any margins. Maximum printable area is 203.2 x 347 mm (8 “x 13.7”), which leaves a 4mm unprintable margin around the perimeter of the page.

How to Remove Borders When Printing to an HP Printer. HP Designjet Printers. Change Printing Preferences (Windows 10). The printer leaves white borders on the page

Once at work I was asked to make a greeting card in a very short time for a memorable address for the anniversary of one of the employees. There was no opportunity to use Photoshop at that time, so I just inserted a nice picture into Word, made it “according to the text”, typed the congratulatory text and sent it to print. But here a problem arose: our HP DeskJet 5943 inkjet color printer did not print the document the way it looked on the monitor screen. On the sheet

I set all margins to 0 in the “Page settings” in Word, then in the printer properties I chose “Paper size: No frames.”. it did not help. From MS Word, our printer was printed with borders and nothing else. But the images (jpeg, png, etc.) from the image viewer, as it turned out, were printed with minimal margins. That was fine with me. Then I decided to just transform my Word document into a picture.

This can be done using a special program. a pdf printer. There are many such utilities, but I especially liked the Universal Document Converter, which can convert documents Not only to PDF-format, but also to many graphic files. Here you can download a demo version of the program for free, the difference from the full version is adding a watermark to the created files. If you want the full version and don’t want to pay anything for it, Yandex and Google will always help. It’s up to you to decide.

So, here are the steps that I had to do: 1. Install the Universal Document Converter. 2. Open our document in Word. click on the menu bar “File”. “Print”. select our pdf printer. “Properties”.

On the left, select the item “Load settings”. “Text document to PDF”. “Open”. Again, in the left pane, select “File format”. put “JPEG” (or PNG, etc.). “OK”. We got a picture from the document.

Open the resulting picture in the image viewer and send it to print (in the settings of the HP DeskJet printer in the “Paper / quality” item I selected “Frameless A4 210 by 297 mm” and “Print quality” set “Best”).

READ  Connect Printer To Phone Via HP Wi-Fi

Views: 39687 nbsp nbsp nbsp nbsp nbsp nbsp

How to remove margins on a page when printing on an HP printer

Opposite Borderless printing uncheck.

Captain obvious, did not ask if only it was that SIMple.

In fact of the matter. Not so SIMple. On the plotter, I found, but in the skate and in the keser, the comments of this tick.

Reducing margins when printing PDF

Open the PDF document, go to “File”. “Print”. In dialog boxes, increasing the scale so that the margins on the page are reduced. In the “Resize” option, set more than 100% and look at the preview on the right side of the window.

Press the “Print” button and get a printout with minimal margins.

Removing page margins in MS Word

It should be noted right away that experts DO NOT recommend harvesting fields for 2 reasons:

  • Text that is located in the printable area, that is, within the margins, will not be printed.
  • For official documents, this is a gross violation of regulations.

However, there are situations in which it is necessary to completely remove fields, so we offer a SIMple way:

  • Go to the “Layout” tab, select the “Fields” option and click on the bottom button “Custom Fields”.
  • In the “Parameters” dialog box Set the minimum size of the fields. 0.1 cm. Keeping the specified parameters.

Now text or images will be positioned from edge to edge, with no margins and white space.

How to reduce margins when printing?

You have prepared a document for printing, clicked “Print”, but a warning message appears on the computer screen:

Many printer models cannot print edge-to-edge on the page, so when printed, some of the text outside the printable area is “lost”. Or, the printing device alerts the user with a message. Experts do NOT recommend completely removing fields, but you can easily reduce them to the required minimum. We offer an easy way to reduce margins when printing on the entire document or only on its fragment.

Reducing margins when printing Word and Excel

  • Open the Word document, select the “Layout” tab and go to the “Fields” option. Here we click on the “Custom Fields” function.
  • A window will appear in which you specify the required field values. Save changes and send to print.

To print an Excel document, we repeat almost the same steps: go to the “Page Layout” tab. “Fields”. “Custom Fields”:

Here you can manually adjust the size of the margins and center the table horizontally or vertically on the page. Then click “View” the result and send it to print.

If you need to reduce the margins only on a certain piece of text, then you need to go to “Page settings”:

In the dialog box, specify the “Apply” option. “To selected text”:

How to remove margins when typing in a Word?

Margins in a Word document are empty space at the edges of the sheet. Texts, images, tables, diagrams and other graphic elements are located in the print area, that is, inside THESE fields. Therefore, the slightest change or inconsistency of the content with the specified parameters may become a prerequisite for Incorrect printout. In this article, we will explain in detail how to remove margins when printing, as well as how to adjust and correct their appropriate size.

How to remove the frame / borders / edges from the edge of the sheet in Photoshop when printing?

It depends on your printer, many of them are physically incapable of borderless printing. Look for borderless printing in printer settings.

And Photoshop. What is the culprit? Set up a printer, not a program

In fact, this is configured in the settings of the printer itself. But it happens that the frame disappears when printing an image only when using the software supplied with the printer. For example for EPSON. “EPSON Easy Photo Print”.

Recommendations for setting and changing fields

  • Sometimes you need to change or remove fields in all documents that will be created in MS Word. To do this, go to the “Fields”. “Custom fields” and select the “Default” function in the window that appears. All changes that you made to the page settings will be saved and become a template for all subsequent documents.
  • If you need to change the size of the margins only in a certain place of the document, then go to Options, at the bottom of the dialog box in the “Apply” option, set “To selected text”.

In this case, you need to select the “Fix” button and increase the parameters of the fields. Otherwise, the text will be cut off or NOT printed at all (a warning will appear again).

An article on how to remove margins when printing in a Word, written with the support of the specialists of the Printside.Ru copy center

How to remove the border around a photo when printing?

If the printer supports this mode, it should have a borderless bird in its settings. Well, the proportions of the photo must also match the proportions of the paper.

Enable Borderless Printing Tab.

And even if you print on an Epson printer on 10×15 paper, you need to set the Storn ratio 4×6, this is indicated in inches

Print Setup Menu

If you intend to use your printer permanently for borderless printing, you can configure this setting from the control menu of the device itself. This will allow you to set changes only once and make them apply when sending each document to print. Regardless of the equipment model, this task is performed in the same way, and the aLGorithm of actions looks like this:

    Open the Start menu and go from there to Settings.

Among the list of all sections, open “Devices”.

Find the device for which you want to set up borderless printing and click on it to display the menu.

All the necessary parameters for solving the problem are located in the “control”.

Select the Page or Print tab.

Set the “Borderless” option as the page layout or find it in another block of settings. their location depends on the make and model of the printer.

If the printer supports different types of paper, a separate notification will appear, where you need to specify for which paper the changes are made.

All that remains is to print a document that already has fields to check if the printer ignores them now. If suddenly the fields have NOT disappeared anywhere, try restarting your computer and printing equipment, and then repeat the operation.

Branded printer application

This option is suitable for those users who prefer to send documents through a proprietary printer application and, accordingly, it is installed on the computer itself. Let’s clarify that not all devices support such solutions, which are installed together with the main driver.

    Follow the steps outlined in the previous method to find your printer in the list and display its controls. Under its name, click on the line “Open printer application”.

Start the task of printing documents by clicking on the dedicated button.

In the “Explorer” window, select a text file or PDF document that you want to send for borderless printing.

When setting up printing Change the values ​​of the item to get rid of the following fields.

If it is not in the main menu, go to the “Other options” section and look for it there.

It will NOT work to give an exact description of the location of this parameter, since each application differs in its appearance and functional features.

Setting up the printer for borderless printing

Program for working with documents

If the document is to be sent to borderless printing once, it makes no sense to constantly switch the parameter in the printer settings. Instead, you can only set it once when interacting with the program itself, where the document is being prepared. It can be any text editor, the principle of further actions will NOT change in any way.

    Open the “File” section and go to “Print” through the drop-down menu. You can also launch this component using the Ctrl P hotkey.

In the printer selection menu, select the one you want to use for printing, and then click on the “Properties” button.

Open the Page tab, which we already talked about in method 1, and select the borderless printing mode, then go back and start the process.

Document editing

Sometimes the only working way will be to edit the document itself by removing the fields through the software in which you work with it. There is a separate article on our site dedicated to how to cope with the task in Word, and you just have to adapt the instructions for the text editor you are using and start borderless printing.