How to remove the cartridge from your printer brother

Removing cartridges from HP printers

As mentioned earlier, there are laser and inkjet devices. They are in approximately the same demand, so they are distributed in the same way. Because of this, we would like not to focus on any one type, but to tell in detail about each, presenting separate instructions.

Laser Devices

Laser printers use a black toner cartridge that is much faster than inkjet models. The toner itself is one of the components of the cartridge, where there is an imaging drum and other important elements. This entire block is removed from the printer, and only then it is refilled. The whole procedure is completed in just a few minutes:

  • Turn off the printer and disconnect power. Only proceed to the next step after making sure that the printer is cool and that the room is at a normal temperature and humidity. Precautions are necessary to ensure that the remaining powder does not collapse into lumps, complicating the refueling operation.
  • Open the top cover by moving your hand in the appropriate direction.

remove, cartridge, printer, brother

Grasp the cartridge by the handle and pull it lightly. If you suddenly feel that some part is interfering with normal removal, carefully examine the insides. you may have to open the securing latch on both sides of the cartridge.

If you need to further transport the cartridge, wrap it in bubble wrap and put it in a dark box.

When proceeding with the removed ink tank, take special care: hold the structure by the edges so as not to touch fragile parts with your hands. If you need to self-refill the cartridge, we recommend that you familiarize yourself with our separate material on this topic by clicking on the link below.

How to remove the cartridge from the printer brother

To replace the Brother TN-2175 Toner Cartridge, make sure the printer is turned off.

Pull on the flat handle of the cartridge and remove it from the printer:

Place the Brother TN-2175 toner cartridge on top of the pre-prepared junk newspaper.

To avoid damaging the printer, do not touch the electrodes shown in the following figure:

Locate the green lever on the cartridge, push it down, and separate the toner cartridge from the drum cartridge:

Attention! Do not place the toner cartridge near open flames, do not spill toner on your skin or clothing, or touch the drum unit or other sensitive parts of the cartridge:

Unpack the new toner cartridge. Hold the toner cartridge horizontally with both hands and shake it from right to left several times to distribute the toner evenly.

Attention! Unpack the toner cartridge just before installing it in the printer. If you unpack it and do not use it for a long time, toner life will decrease.

Carefully remove the protective cover from the new Brother TN-2175 Toner Cartridge:

Lift the toner cartridge by the handle and push it firmly into the drum cartridge assembly until it clicks into place. If you installed the toner cartridge correctly, the lock lever will automatically lift up.

Find the green slider on the cartridge and slide it several times to the right and left until it stops. This will clean the corona wire of the drum unit.

Attention: return the slider foot (1) to its original position, otherwise a vertical dark line will appear on the print.

Install the Brother TN-2175 cartridge back into the printer. Close the front cover of the printer:

Attention! Do not turn off the power of the printer or open its front cover until the “Ready” indicator is on.

  • Homepage
  • Russia
  • HL-2035R
  • Frequently asked questions and troubleshooting
  • Consumables / Paper / Accessories
  • Replaceable components and consumables
  • faq00000065_045
  • Date: 29.05.2012
  • Number: faq00000065_045
  • Printing
  • Email

Replacing the Toner Cartridge

Follow the instructions below to replace the toner cartridge:

This Brother machine has a separate drum unit and toner cartridge. Make sure you are replacing only the toner cartridge and not the drum unit. For information on the differences between these consumables, see the question “What is the difference between a toner cartridge and an imaging drum?”.

NOTE: The illustrations below are of the typical model and may differ from your Brother model.

Do not use any type of aerosol to clean the inside and outside of the device. Doing so may result in fire or electric shock.

If the Toner light is on, the printer is out of toner or the toner is unevenly distributed in the cartridge.

  • Use Genuine Brother toner cartridges for high quality printing. Contact your Brother dealer to purchase toner cartridges.
  • It is recommended that you clean the printer when replacing a toner cartridge. See question How to clean the inside of the printer?
  • Open the front cover of the printer.

Hold your Brother machine with one hand and the drum unit with the other. Pull the drum unit towards you, and then lift up.

  • We recommend that you place the drum unit and toner cartridge assembly on a piece of disposable paper or cloth in case you accidentally spill or spill toner.
  • To avoid damaging the printer from static electricity, do not touch the electrodes shown in the figure below.
  • Handle the toner cartridge with care. If you spill toner on your hands or clothing, shake it off immediately or wash it off with cold water.
  • Be sure to close the cartridge tightly and pack it in a bag. to prevent scattering of toner.
  • Dispose of the used toner cartridge separately from household waste according to local regulations. If you have any questions, please contact the appropriate department of your local administration.

Unpack the new toner cartridge. Grasp the cartridge with both hands and gently shake the cartridge from side to side 5-6 times to distribute the toner evenly inside the cartridge.

  • A new toner cartridge should be unpacked just before you install it in the printer. If a toner cartridge is unpacked and left unused for a long time, the toner cartridge life may be reduced.
  • If an unpacked drum unit is exposed to direct sunlight or indoor lighting, it may be damaged.
  • Brother strongly discourages refilling used toner cartridges. It is also strongly recommended that you only use original (manufactured by Brother Industries, Ltd.) Brother toner cartridges. Using or attempting to use potentially incompatible toner and / or toner cartridges with your device may damage your device and / or degrade print quality. The Brother warranty does not cover defects caused by the use of unauthorized third party ink and / or cartridges. Replace toner cartridges with genuine Brother supplies to protect your investment and ensure high quality prints.
  • The use of third-party toner or toner cartridge may result in poor print quality as well as a decrease in the life of the printer itself. It can also damage and shorten the life of the drum unit. The Brother Warranty does not cover failures caused by the use of third-party toner or toner cartridges.
  • Install the toner cartridge in the drum unit immediately after removing the protective cover. To avoid deterioration in print quality, do not touch the gray areas in the illustration.

Make sure the toner cartridge is installed correctly, otherwise it may separate from the drum unit.

HP has been manufacturing printers and multifunctional products for many years. Among the models of this equipment, there are both laser and inkjet machines, differing not only in the printing aLGorithm, but also in structure. Each of these models has at least one cartridge, which sometimes needs to be refilled. You can do this yourself, but you will need to remove the ink bottle before starting the procedure.

Inkjet devices

In inkjet technology, two or four cartridges are usually installed, depending on the used printer or MFP model. They do not form a single system as is done in laser equipment, but are separate small components that are installed in appropriate places. Each of these containers is removed individually, and this can be done as follows:

  • Turn off the power to the printer and wait until it stops working completely.
  • Open the top cover according to its design. For example, in some devices, it is enough to lower it down by grasping a special recess, and sometimes you need to press the corresponding button and completely detach the panel.

Then press on the cartridge until a characteristic click appears. If there is a holder, you must first lift it up, otherwise you will not be able to detach the ink tank.

After that, you can proceed to installing new cartridges, refilling existing ones, cleaning them, or connecting a continuous ink supply system. Read about all these procedures in expanded form in our other materials listed below.

As for the disposal of cartridges, this must be done in accordance with the established rules of the area of ​​residence, because such elements need to be recycled, and when they are thrown out in the wrong places, nature is polluted with materials that do not decompose for a long time.

You are now familiar with cartridge removal techniques for different types of printing equipment. Although we have indicated various nuances, there are still many varieties of models and series of devices with their own technical features that must be taken into account in any interventions in the system. Therefore, before removing the cartridge, we strongly recommend the available instructions for the model used.

Thank the author, share the article on social networks.

Removing cartridges from HP printers

As mentioned earlier, there are laser and inkjet devices. They are in approximately the same demand, so they are distributed in the same way. Because of this, we would like not to focus on any one type, but to tell in detail about each, presenting separate instructions.

How to remove the cartridge from the printer brother

To replace the Brother TN-2175 Toner Cartridge, make sure the printer is turned off.

Pull on the flat handle of the cartridge and remove it from the printer:

Place the Brother TN-2175 toner cartridge on top of the pre-prepared junk newspaper.

To avoid damaging the printer, do not touch the electrodes shown in the following figure:

Locate the green lever on the cartridge, push it down, and separate the toner cartridge from the drum cartridge:

Attention! Do not place the toner cartridge near open flames, do not spill toner on your skin or clothing, or touch the drum unit or other sensitive parts of the cartridge:

READ  Printer monitor scanner headphones what is superfluous

Unpack the new toner cartridge. Hold the toner cartridge horizontally with both hands and shake it from right to left several times to distribute the toner evenly.

Attention! Unpack the toner cartridge just before installing it in the printer. If you unpack it and do not use it for a long time, toner life will decrease.

Pack the used toner cartridge tightly in the bag, making sure no toner residues spill out of the bag. Dispose of the toner cartridge separately from household waste.

Carefully remove the protective cover from the new Brother TN-2175 Toner Cartridge:

Lift the toner cartridge by the handle and push it firmly into the drum cartridge assembly until it clicks into place. If you installed the toner cartridge correctly, the lock lever will automatically lift up.

Find the green slider on the cartridge and slide it several times to the right and left until it stops. This will clean the corona wire of the drum unit.

Attention: return the slider foot (1) to its original position, otherwise a vertical dark line will appear on the print.

Install the Brother TN-2175 cartridge back into the printer. Close the front cover of the printer:

Attention! Do not turn off the power of the printer or open its front cover until the “Ready” indicator is on.

  • Homepage
  • Russia
  • HL-2035R
  • Frequently asked questions and troubleshooting
  • Consumables / Paper / Accessories
  • Replaceable components and consumables
  • faq00000065_045
  • Date: 29.05.2012
  • Number: faq00000065_045
  • Printing
  • Email

Replacing the Toner Cartridge

Follow the instructions below to replace the toner cartridge:

This Brother machine has a separate drum unit and toner cartridge. Make sure you are replacing only the toner cartridge and not the drum unit. For information on the differences between these consumables, see the question “What is the difference between a toner cartridge and an imaging drum?”.

NOTE: The illustrations below are of the typical model and may differ from your Brother model.

Do not use any type of aerosol to clean the inside and outside of the device. Doing so may result in fire or electric shock.

If the Toner light is on, the printer is out of toner or the toner is unevenly distributed in the cartridge.

  • Use Genuine Brother toner cartridges for high quality printing. Contact your Brother dealer to purchase toner cartridges.
  • It is recommended that you clean the printer when replacing a toner cartridge. See question How to clean the inside of the printer?
  • Open the front cover of the printer.

Hold your Brother machine with one hand and the drum unit with the other. Pull the drum unit towards you, and then lift up.

  • We recommend that you place the drum unit and toner cartridge assembly on a piece of disposable paper or cloth in case you accidentally spill or spill toner.
  • To avoid damaging the printer from static electricity, do not touch the electrodes shown in the figure below.
  • Handle the toner cartridge with care. If you spill toner on your hands or clothing, shake it off immediately or wash it off with cold water.
  • Be sure to close the cartridge tightly and pack it in a bag. to prevent scattering of toner.
  • Dispose of the used toner cartridge separately from household waste according to local regulations. If you have any questions, please contact the appropriate department of your local administration.

Unpack the new toner cartridge. Grasp the cartridge with both hands and gently shake the cartridge from side to side 5-6 times to distribute the toner evenly inside the cartridge.

  • A new toner cartridge should be unpacked just before you install it in the printer. If a toner cartridge is unpacked and left unused for a long time, the toner cartridge life may be reduced.
  • If an unpacked drum unit is exposed to direct sunlight or indoor lighting, it may be damaged.
  • Brother strongly discourages refilling used toner cartridges. It is also strongly recommended that you only use original (manufactured by Brother Industries, Ltd.) Brother toner cartridges. Using or attempting to use potentially incompatible toner and / or toner cartridges with your device may damage your device and / or degrade print quality. The Brother warranty does not cover defects caused by the use of unauthorized third party ink and / or cartridges. Replace toner cartridges with genuine Brother supplies to protect your investment and ensure high quality prints.
  • The use of third-party toner or toner cartridge may result in poor print quality as well as a decrease in the life of the printer itself. It can also damage and shorten the life of the drum unit. The Brother Warranty does not cover failures caused by the use of third-party toner or toner cartridges.
  • Install the toner cartridge in the drum unit immediately after removing the protective cover. To avoid deterioration in print quality, do not touch the gray areas in the illustration.

Make sure the toner cartridge is installed correctly, otherwise it may separate from the drum unit.

HP has been manufacturing printers and multifunctional products for many years. Among the models of this equipment, there are both laser and inkjet machines, differing not only in the printing aLGorithm, but also in structure. Each of these models has at least one cartridge, which sometimes needs to be refilled. You can do this yourself, but you will need to remove the ink bottle before starting the procedure.

Laser Devices

Laser printers use a black toner cartridge that is much faster than inkjet models. The toner itself is one of the components of the cartridge, where there is an imaging drum and other important elements. This entire block is removed from the printer, and only then it is refilled. The whole procedure is completed in just a few minutes:

  • Turn off the printer and disconnect power. Only proceed to the next step after making sure that the printer is cool and that the room is at a normal temperature and humidity. Precautions are necessary to ensure that the remaining powder does not collapse into lumps, complicating the refueling operation.
  • Open the top cover by moving your hand in the appropriate direction.

Grasp the cartridge by the handle and pull it lightly. If you suddenly feel that some part is interfering with normal removal, carefully examine the insides. you may have to open the securing latch on both sides of the cartridge.

If you need to further transport the cartridge, wrap it in bubble wrap and put it in a dark box.

When proceeding with the removed ink tank, take special care: hold the structure by the edges so as not to touch fragile parts with your hands. If you need to self-refill the cartridge, we recommend that you familiarize yourself with our separate material on this topic by clicking on the link below.

Inkjet devices

In inkjet technology, two or four cartridges are usually installed, depending on the used printer or MFP model. They do not form a single system as is done in laser equipment, but are separate small components that are installed in appropriate places. Each of these containers is removed individually, and this can be done as follows:

  • Turn off the power to the printer and wait until it stops working completely.
  • Open the top cover according to its design. For example, in some devices, it is enough to lower it down by grasping a special recess, and sometimes you need to press the corresponding button and completely detach the panel.

Then press on the cartridge until a characteristic click appears. If there is a holder, you must first lift it up, otherwise you will not be able to detach the ink tank.

After that, you can proceed to installing new cartridges, refilling existing ones, cleaning them, or connecting a continuous ink supply system. Read about all these procedures in expanded form in our other materials listed below.

As for the disposal of cartridges, this must be done in accordance with the established rules of the area of ​​residence, because such elements need to be recycled, and when they are thrown out in the wrong places, nature is polluted with materials that do not decompose for a long time.

You are now familiar with cartridge removal techniques for different types of printing equipment. Although we have indicated various nuances, there are still many varieties of models and series of devices with their own technical features that must be taken into account in any interventions in the system. Therefore, before removing the cartridge, we strongly recommend the available instructions for the model used.

Thank the author, share the article on social networks.

Why does paper jam in the printer??

  • Bad paper: old, wrinkled, previously used. Just do not use such paper: it is cheaper than later repairing a printer that has suffered from a failed paper jam and pulling out of the paper.
  • Unsuitable paper: Too thin or thick, not of the standard required by your particular copier, and therefore, for example, sheets stick together and get jammed.
  • Sticking sheets to each other, magnetization. In this situation, it will help to knock the edge of the stack of paper on the table or flip through all the sheets to separate them. If you are printing on the second side of the sheet, then let the printed sheets cool down and also separate the sheets.

When inserting a stack of sheets, make it a rule to always flip through it at the bend

You can also remove the entire stack of paper from the tray and insert it upside down. Also, this problem can be caused by the fact that paper of different types and weights was put in the printer to complete the same job.

  • Too much paper loaded in the tray. put less, or too little paper and the printer cannot pick up the sheet. put more.
  • The paper is not inserted straight into the bypass tray, and when it is picked up by the printer, it is crooked, skewed, and eventually jams. Here it will only help to gently insert the paper into the manual feed tray and adjust the clamps on the left and right of the sheet exactly to its size.

Insert paper into the bypass tray or “slot” gently, evenly,
adjust the clamps on the left and right to exactly the width of the sheet

READ  Doesn't Print Printer Prints Test Page

Adjust the width of the clamp for the sheet on which we will print

The sheet should lie flat, and the clamps should fit exactly under its width

  • Paper with staples, staples, crumbs and dust is inserted. First, always check when reusing the sheet for any staples or staples. you can simply cut them off at the corner with scissors. Also, put a table next to the copier in the organization so that all employees will be able to remove paper clips and staples from the sheets on it, and not over the printer. this will help to avoid accidental entry of foreign objects into the machine.
  • Too thin or thick paper. If you are using paper of non-standard weight, then before printing in the printer settings (Properties button), specify the paper type: thick, thin, film, cardboard, etc.
  • Paper size. Sometimes the paper jam sensors can be triggered, even if there was actually none. This may be due simply to sensor problems, as well as to the fact that in the print settings is, for example, A4 paper size, and you are printing on envelopes. The printer will not see that the sheet has passed through the sensors and “thinks” that a jam has occurred. To avoid this, before printing in the printer settings (Properties button), specify the paper size.
  • Opening the tray at the time of printing. Never open the paper feed trays before you finish printing.

How to remove paper from the printer?

If, nevertheless, the paper in the printer is jammed and the “Paper jam” or “Paper jam” light comes on, then you need to act very carefully: strong jerks can damage the machine, and the print quality and reliability of its operation will never be the same.

So, the first thing to do is to remove the jammed paper from the printer, turn it off and on. If the jam is small, the drum will spin and the paper will pop out by itself.

If this does not help, then you need to review the paper removal guidelines for your printer. The more complex the device, the more detailed it will be described: some modern devices even write what to do and draw diagrams on displays.

The general rules for pulling out paper are as follows: you need to drag the sheet slowly, without jerking and with both hands, holding both sides, otherwise the sheet will break, and it is much more difficult to pull out the jammed pieces of paper. Individual copies can treacherously remain inside and interfere with further work.

When removing the cartridge, if necessary, grasp it only by the handle, place it on a flat surface, do not touch the green drum and other spare parts: this can lead to poor print quality and the appearance of streaks and spots on the prints.

Next, determine where exactly the paper is jammed in the printer. Variants may howl:

  • input trays where paper is fed;
  • areas where paper exits the printer (top and back);
  • cartridge area;
  • the bowels of the printer, where the paper falls, but it is not visible even when all trays and doors are open.

Actually, you can pull out the paper by checking each of these options: turn off the printer by a button or from the network, open the door, see if there is paper there, if there is, take it with both hands and gently pull.

Finding and removing paper from the main paper feed tray.
The printer may not have been able to pick up the sheet and it is right in the tray

Often, if there were problems with sheet picking, but the printer still pulled it through,
it gets stuck at the exit: just easily pull the sheet towards you and it will come out

If the sheet is not visible at the entrance or exit, look at the back of the printer:
most likely there is an opening door and a sheet there.
The door, by the way, needs to be opened when printing on thick sheets.

If there is no paper in the trays, open the door behind which the cartridge is located and pull it out using only the handle. Check to see if the paper is jammed in the area of ​​the cartridge:

How to remove paper jammed in the cartridge area

In these photos, I showed where the paper could be. If the device is more complicated, then look for other doors and look at the paper in them. But with complex and expensive devices, it is better not to self-medicate, but to find instructions on a specific device on the Internet.

There are situations when it is impossible to pull the paper out of the printer on your own. In this case, it remains to contact the service center or workshop.

Continue printing

If you manage to pull out the jammed sheet, try turning on the printer again by doing a so-called “reset”. The printer will most likely continue printing from the point where the jam occurred. The page will be printed again and then the printing process will resume without any difficulty. Check again that all pages have been printed.

If after restarting the printer does not continue to work, then start printing again by selecting the necessary settings.

Inkjet

The design of inkjet printers is designed in such a way that it will not be possible to gain access to the rotating rollers immediately. they are securely covered with a cartridge. Disconnect the printer from the power supply before use. You should not disassemble the printer yourself if you are inexperienced and new to its internal mechanisms. This is especially true when the paper is not completely removed, and part of the sheet is “chewed” by the device.

In such a situation, entrust the solution of the problem to qualified specialists of the service center.

However, some manufacturers make it easier to operate their equipment. For example, HP’s inkjet models have developed a special encoder strip sensor. With its help, the position of the carriage at the start and finish of printing is determined. If a paper jam occurs and printing stops, check if the sensor is okay. It may be clogged or mechanically damaged, causing the printer to be unable to complete printing. To resume operation, wipe the encoder strip sensor with a cloth dampened with alcohol. It is better to remove the jammed sheet of paper beforehand.

How to remove paper from your printer brother

Sooner or later, every user of a printer or copier is faced with a paper jam problem: the icon lights up, and the printer refuses to print further. What to do in this situation? How do I remove the paper myself and continue printing? Why paper jams in the printer and how to avoid it later?

The sponsor of the publication is the BeRrint company, which provides printing services:
printing of business cards, leaflets, flyers, invitations,
as well as large-format printing on plotters, plotter cutting.

There are many reasons for paper jams in the printer, but they all boil down to two main ones:

  • worn parts of the printer (for example, paper feed rollers);
  • the rules for working with the printer are violated.

The first reason arises during prolonged or inaccurate use of the device, when the resource of the parts has already exhausted itself. In this case, the specialists of the service center or in the workshop can fix the problems. There are many errors of the second plan, and they are eliminated by the users themselves. (Read the article: How to organize the work of copying equipment at school and ensure its smooth operation).

Extraction nuances in different printers

Remember that different types of printers have slightly different troubleshooting methods.

How to continue printing after a paper jam?

After removing the paper, turn on the printer. Most likely, it will continue printing from the moment of the jam, repeating the same page one more time, but just in case, check if it is printed. If the print order is not saved, then select the required sheets to print and press print.

Thanks for your rating. If you want your name
it became known to the author, enter the site as a user
and click Thank you again. Your name will appear on this page.

Like the material?
Want to read later?
Save on your wall and
share with your friends

You can place an article announcement on your website with a link to its full text

  • Homepage
  • Russia
  • HL-2040R
  • Frequently asked questions and troubleshooting
  • Paper feed / Paper jam
  • Paper jam
  • faq00000026_006
  • Date: 04/06/2015
  • Number: faq00000026_006
  • Printing
  • Email

If a paper jam occurs, the Paper light will beep as shown below.

Some parts inside the printer remain very hot immediately after using the printer. If you opened the front cover or face-up paper exit tray, never touch the shaded parts shown below.

To prevent damage to the printer by static electricity, do not touch the terminals shown below.

To avoid print quality problems, do not touch the shaded part of the product shown in the illustration. If you do accidentally touch this part, wipe the surface with a dry, soft, lint-free cloth.

You urgently need to print an important document, and an unpleasant message pops up on the screen: paper is jammed, or the indicator on the front of the printer blinks red, which notifies of an error. The instrument jammed the pages, an error occurred, and the operation stopped. What to do if paper is jammed in the printer, how to pull it out neatly and without damage? We will try to understand this issue and find out how to fix the paper jam problem in the printer.

How to continue printing after a paper jam?

After removing the paper, turn on the printer. Most likely, it will continue printing from the moment of the jam, repeating the same page one more time, but just in case, check if it is printed. If the print order is not saved, then select the required sheets to print and click print.

Thanks for your rating. If you want your name
it became known to the author, enter the site as a user
and click Thank you again. Your name will appear on this page.

READ  What can be done from an old inkjet printer

Like the material?
Want to read later?
Save on your wall and
share with your friends

You can place an article announcement on your website with a link to its full text

  • Homepage
  • Russia
  • HL-2040R
  • Frequently asked questions and troubleshooting
  • Paper feed / Paper jam
  • Paper jam
  • faq00000026_006
  • Date: 04/06/2015
  • Number: faq00000026_006
  • Printing
  • Email

If a paper jam occurs, the Paper light will beep as shown below.

Some parts inside the printer remain very hot immediately after using the printer. If you opened the front cover or face-up paper exit tray, never touch the shaded parts shown below.

To prevent damage to the printer by static electricity, do not touch the terminals shown below.

To avoid print quality problems, do not touch the shaded part of the product shown in the illustration. If you do accidentally touch this part, wipe the surface with a dry, soft, lint-free cloth.

You urgently need to print an important document, and an unpleasant message pops up on the screen: paper is jammed, or the indicator on the front of the printer blinks red, which notifies of an error. The instrument jammed the pages, an error occurred, and the operation stopped. What to do if paper is jammed in the printer, how to pull it out neatly and without damage? We will try to understand this issue and find out how to fix the paper jam problem in the printer.

Why does paper jam in the printer??

  • Bad paper: old, wrinkled, previously used. Just do not use such paper: it is cheaper than later repairing a printer that has suffered from a failed paper jam and pulling out of the paper.
  • Unsuitable paper: Too thin or thick, not of the standard required by your particular copier, and therefore, for example, sheets stick together and get jammed.
  • Sticking sheets to each other, magnetization. In this situation, it will help to knock the edge of the stack of paper on the table or flip through all the sheets to separate them. If you are printing on the second side of the sheet, then let the printed sheets cool down and also separate the sheets.

When inserting a stack of sheets, make it a rule to always flip through it at the bend

You can also remove the entire stack of paper from the tray and insert it upside down. Also, this problem can be caused by the fact that paper of different types and weights was put in the printer to complete the same job.

  • Too much paper loaded in the tray. put less, or too little paper and the printer cannot pick up the sheet. put more.
  • The paper is not inserted straight into the bypass tray, and when it is picked up by the printer, it is crooked, skewed, and eventually jams. Here it will only help to gently insert the paper into the manual feed tray and adjust the clamps on the left and right of the sheet exactly to its size.

Insert paper into the bypass tray or “slot” gently, evenly,
adjust the clamps on the left and right to exactly the width of the sheet

Adjust the width of the clamp for the sheet on which we will print

The sheet should lie flat, and the clamps should fit exactly under its width

  • Paper with staples, staples, crumbs and dust is inserted. First, always check when reusing the sheet for any staples or staples. you can simply cut them off at the corner with scissors. Also, put a table next to the copier in the organization so that all employees will be able to remove paper clips and staples from the sheets on it, and not over the printer. this will help to avoid accidental entry of foreign objects into the machine.
  • Too thin or thick paper. If you are using paper of non-standard weight, then before printing in the printer settings (Properties button), specify the paper type: thick, thin, film, cardboard, etc.
  • Paper size. Sometimes the paper jam sensors can be triggered, even if there was actually none. This may be due simply to sensor problems, as well as to the fact that in the print settings is, for example, A4 paper size, and you are printing on envelopes. The printer will not see that the sheet has passed through the sensors and “thinks” that a jam has occurred. To avoid this, before printing in the printer settings (Properties button), specify the paper size.
  • Opening the tray at the time of printing. Never open the paper feed trays before you finish printing.

Inkjet

The design of inkjet printers is designed in such a way that it will not be possible to gain access to the rotating rollers immediately. they are securely covered with a cartridge. Disconnect the printer from the power supply before use. You should not disassemble the printer yourself if you are inexperienced and new to its internal mechanisms. This is especially true when the paper is not completely removed, and part of the sheet is “chewed” by the device.

In such a situation, entrust the solution of the problem to qualified specialists of the service center.

However, some manufacturers make it easier to operate their equipment. For example, HP’s inkjet models have developed a special encoder strip sensor. With its help, the position of the carriage at the start and finish of printing is determined. If a paper jam occurs and printing stops, check if the sensor is okay. It may be clogged or mechanically damaged, causing the printer to be unable to complete printing. To resume operation, wipe the encoder strip sensor with a cloth dampened with alcohol. It is better to remove the jammed sheet of paper beforehand.

Jam reasons

So why is this failure occurring? In fact, there are many reasons why a sheet of paper may remain in the printer. If you know in advance about possible problems with office equipment, most of them can be easily avoided.

  • Poor quality paper is perhaps one of the most common reasons. If you have purchased cheap paper, use old, previously used sheets, then be prepared for possible consequences. Poor quality products can be easily damaged and be “eaten” by printing equipment.
  • Damage to paper pages: wrinkled edges, tears, folds very often lead to the fact that the transfer mechanism of the printing device chews them up.
  • Excessive moisture in the paper. If the paper has been stored improperly (damp, high humidity), or you have spilled something on it before, be careful: the sheets may stick to each other and become jammed as a result.
  • On the contrary, excessive dryness of the paper. Due to static voltage, the sheets easily electrify and begin to stick to each other.
  • Very thin or thick paper of the wrong standard required by a particular brand of printer. Before using the printer, check the information on what sheet density it can accept.
  • Foreign objects inside. Sometimes the smallest office debris (paper clips, caps, staples, pencil lead, dust, etc.) can get into the inside of the equipment, this will also sooner or later lead to malfunctions.
  • Normal wear and tear of rotating rollers, their mechanical damage, and other violations of the rules for working with the printer.

How to remove paper from your printer brother

Sooner or later, every user of a printer or copier is faced with a paper jam problem: the icon lights up, and the printer refuses to print further. What to do in this situation? How do I remove the paper myself and continue printing? Why paper jams in the printer and how to avoid it later?

The sponsor of the publication is the BeRrint company, which provides printing services:
printing of business cards, leaflets, flyers, invitations,
as well as large-format printing on plotters, plotter cutting.

There are many reasons for paper jams in the printer, but they all boil down to two main ones:

  • worn parts of the printer (for example, paper feed rollers);
  • the rules for working with the printer are violated.

The first reason arises during prolonged or inaccurate use of the device, when the resource of the parts has already exhausted itself. In this case, the specialists of the service center or in the workshop can fix the problems. There are many errors of the second plan, and they are eliminated by the users themselves. (Read the article: How to organize the work of copying equipment at school and ensure its smooth operation).

Laser

The above instructions on how to pull out the paper are also relevant for laser printers. Everything is much simpler here: laser printers, unlike inkjet printers, do not have to be disconnected from the power supply and turned on again. The most important thing is not to pull out the page abruptly, jerkily, otherwise it may tear. Modern models of laser printers (for example, Epson, Brother, etc.) come with a detailed manual, which describes how to solve this problem for a specific model. You can also set the settings for the loaded paper.

Continue printing

If you manage to pull out the jammed sheet, try turning on the printer again by doing a so-called “reset”. The printer will most likely continue printing from the point where the jam occurred. The page will be printed again and then the printing process will resume without any difficulty. Check again that all pages have been printed.

If after restarting the printer does not continue to work, then start printing again by selecting the necessary settings.