How to reset a Brother Dcp cartridge

Instructions on how to reset the cartridge on different printer models

Often users of printing devices are faced with a situation when the printer informs about the need to install a new cartridge, although there is enough ink in it. You can solve the problem on your own. The main thing is to understand what actions will be appropriate and in what sequence they should be performed.

Toner Counter Reset Methods

If the printer, after refilling the cartridge, signals that the ink bottle needs to be replaced, this does NOT mean that there is NO colorant left. Now almost every cartridge is equipped with a chip, whose task is to control ink consumption, based on the number of printed sheets. Therefore, when the limit is reached, the blocking is turned on, because the device sees the ink tank empty.

reset, brother, cartridge

The way out of this situation is to reset the printer cartridge, which can be done independently. There are several ways:

  • Removing the used chip and installing a new one. This is only possible with laser devices. The ink cartridge chip is not replaceable.
  • The use of a universal programmer or a model that is suitable for a specific printing device.
  • Zeroing the cartridge without any tools. For example, the “Reset / Stop” key is pressed and held for 10 seconds. True, in the future, you will need to monitor the paint level yourself.

When the printer reports whether there is not a shortage of ink, but a problem, it will not work to reset the cartridge after refueling. You may need to purchase a new ink tank.

Zeroing on HP models

Many HP cartridge users have resorted to disabling ink control. But for most models, it is possible to reset the cartridge counter. The HP printer is equipped with a dual tracking system. First of all, the chip signals the end of the paint. If he thinks that the ink is completely out, although there is still enough dye on the electronic sensor, the device will ask a question about whether to continue working.

The HP printer will continue to function when refilling ink. If refueling is skipped, the chip will be blocked, and then you will need to buy a new cartridge or reflash the chip.

In some cases, the HP cartridge can be reset. How to do such a job so that the printer constantly accepts the ink bottle like new? You can reset the cartridge as follows:

  • With the help of adhesive tape, the contact is glued, located in the upper left part.
  • The part is inserted into the HP printer.
  • Paper is being removed from the tray.
  • The “Enable” and “Cancel” buttons are pressed at the same time, after which the device will report the absence of sheets.
  • The “Cancel” button is pressed again, and the highlighted inscription disappears.
  • The paper is returned to its place, one letter is printed. This causes the HP machine to detect that the ink tank is full.

When the counter again shows the absence of paint, the tape is removed, which will allow the container to be reset. Similar actions are performed as needed.

Canon Zeroing Features

The question of how to reset the cartridge on their own often worries those who use Canon printers. The essence of the problem is the presence of the chip memory on the ink tank and the printing apparatus. If a new ink tank is installed, the software will indicate that it is full. There is no chip in the tank after refueling, accordingly, the data will not be updated, and the use of the device will become impossible due to its blockage.

You can reset the Canon cartridge, which is not equipped with a chip. Resetting a Canon cartridge is done using:

  • Programmer;
  • Contact blocking;
  • Reset the counter of the Canon printer itself.

It is recommended to reset the capacity after refueling as follows:

  • First, the upper contacts are glued with tape.
  • The ink tank is installed in the machine, after which the information about the absence of the cartridge will be displayed.
  • Next, the second row is sealed, and the container is returned to its place.
  • After an error appears stating that you need to insert the ink tank, it must be pulled out and completely remove the sticky strips.
  • Once the part is reinstalled, Canon will assume the cartridge is full.

Steps to zero out the Canon Pixma dye bottle:

  • If there is an ink cartridge in the device and an inscription appears indicating a low ink content, press “OK” or the “All paper” key;
  • If no further messages are observed, you can continue to work.

If the error “All ink” is provided:

  • Pressing the “OK” key;
  • Holding the “Stop” button for 10 seconds
  • After the message disappears, the Canon counter will be reset.

Deactivating the Canon Pixma cartridge voids the manufacturer’s warranty.

Reset counter on Brother models

Brother printers, in particular the DCP 1510R, are equipped with an ink level control system. This is done so that users try to buy new cartridges, rather than refilling them. However, this situation is extremely disadvantageous for the consumer. Accordingly, the owners of Brother laser products are trying to find the most suitable methods to reset the counter.

How to solve the problem? To zero the Brother cartridge, experts advise using a simple method. For example, if you have a Brother DCP 1510R machine, you will have the following:

  • Remove ink tank and paper.
  • Remove the toner from the cartridge.
  • Insert the base back into the device.
  • Through the sheet tray, get to the button on the left side to reset the counter.
  • Close the lid through which the paint container is installed and wait. When the internal mechanism starts to rotate, release the button literally for 1-2 seconds, and then press and hold it again until the mechanism does NOT stop spinning.

Reset Toner Counter

As a result of the correct actions, the device will not display an error requiring toner replacement. Otherwise, the steps will have to be repeated again.

In order not to buy a new cartridge, you can get by with zeroing it. It is important to follow the instructions carefully to avoid damage to the device.

How to reset brother dcp 1510r cartridge. Internet, gadgets and technology. Reset Toner Counter for Brother Printers

The other day a problem with the Brother MFC-1810R printer arose in relatives. After refilling the starter cartridge, the printer requires replacing the toner. To solve this problem, the printer needs to reset the toner counter. Since the TN-1075 cartridge is distributed among Brother machines, the instruction described here will work for DCP-1510R, DCP-1512R, HL-1110R, HL-1112R, MFC-1810R, MFC-1815R.

So, if your printer displays the “Change toner” error, then you need to do the following sequence of actions:

  • Remove the cartridge and paper from the printer.
  • Remove the toner from the housing. To do this, use the special lever on the cartridge.
  • Insert only the base of the housing into the printer. On the left you will see a button to reset the counter.
  • Insert your hand through the paper tray, feel and hold the button with your finger.
  • Close the cover through which the cartridge is inserted.
  • Wait for the mechanism inside the printer to spin. As soon as it spins, Release the counter reset button for 1-2 seconds (no more), then press it again until the mechanism inside the printer stops.
  • Further two options are possible:
  • If the printer clicks and displays an error “Replace toner”, then you could not catch the correct moment in the previous step (step 6). Go back to step 1 and Do all the steps again (I was able to reset the toner counter correctly only from the fourth time).
  • If you did everything correctly, the device will not peep, the printer display will display the “Change toner” error. Now pull the cartridge base out of the printer, insert the toner, and then put the Assembled cartridge back in. The printer will now work until the next cartridge refill.
READ  HP Laserjet Mfp M28w Cartridge Refill

How to reset brother dcp 1512r cartridge

Some users of office equipment printing have to deal with the need to solve the problem related to how to reset the brother dcp 1512r printer. It should be said that on the Brother dcp 1512r, the toner and drum counters are reset in the same way as on the all-in-one printer brother dcp 1510r. In this case, you DO NOT need to disconnect or unscrew anything, the main thing is not to forget to refill the toner in the consumable container. Everything can be done completely manually without using all kinds of tools. You don’t even need a screwdriver. To reset the toner counter for this printer model, please read the following steps in strict sequence.

Detailed instructions

  • So, if you decide to reset the counter on the brother dcp 1512r printer, in this case, first enable your all-in-one printer, clicked for this purpose the corresponding button on its panel.
  • Next, you should get to the cartridge of this printing office equipment, remove it, and then divide it into two component parts, namely: a block with a photo roll and a block with a dye.
  • After completing the previous step, carefully insert the block from the photo roll back into the printer.
  • Now you should go to the feed tray of the device, from where you need to pull the paper.
  • Insert your hand through this tray, locate the lever or sensor on the left and push it down.
  • Keep it pressed and at the same time slowly close the top cover of the printer.
  • As soon as you hear the characteristic engine noise of the device, you can release the lever. But literally in a second click on it again.
  • You need to keep it until the office equipment warms up and dies down.
  • This completes the Brother dcp 1512r toner counter reset.
  • Open the printer cover, pull out the unit from the photo tray and collect the consumables of the device. Completed this procedure, insert the cartridge back into the device and make a test print. It should be added that you may not be able to start the printing process the first time. Therefore, if necessary, try the reset again, pausing before releasing the lever for about 1 second after the office equipment engine turns on again.

Watch the Brother dcp 1512r toner counter reset video

Resetting the drum counter

Also, we will reset the printer’s photo counter. To do this, perform the following procedure:

  • Click on “Menu”, and scrolled through all the items, select “Device Information”.
  • Clicked on it, now select “Reset drum”.
  • All you need now is to click on the “OK” button and hold it in this state for about 5 seconds.
  • Click on the “Up” arrow, after which the device should show that the photovale resource has returned to 100 percent again.
  • Check the performed reset by printing a report: “Menu” = “Device information” = “Custom settings” = “OK” = “Start”.
  • On the printed report, you must verify that both toner and drum yields are 100 percent.

This completes the steps to reset the toner counter for the brother dcp 1512r. But in the event that for some reason you failed to do this and the printer writes, replace the toner, then purchase a new cartridge or use the services of any reliable service center.

Let’s look at how to reset the counters for Brother HL-1110R, HL-1112R, DCP-1510R, DCP-1512R, MFC-1810R, MFC-1815R printers. THESE models use one cartridge, TN-1075, so the toner and drum counters are reset in the same way.

Reset Toner Counter

How to do this through the device menu. I do not know yet. You can reset the toner counter of the Brother DCP-1512R manually, in the truest sense of the word. The process is simpler than the Brother DCP-7057R model. No need to disconnect and poke with a screwdriver.

We take out the cartridge and divide it into two parts (a toner unit and a drum unit).

Insert the drum unit into the device.

Pulling paper out of the feed tray.

We put our hand through the paper feed tray and press the sensor or lever (located on the left).

    Hold and close the top cover.

As soon as we hear the engine noise, release the sensor and after 1 second press it again.

We hold until the device warms up and dies down.

  • Open the lid, take out the unit with the drum unit, assemble the cartridge, insert it into the device and print.

You may not be able to reset the counter of the Brother DCP-1512R printer right away. Try to repeat the process by pausing before releasing the sensor for about 1 second after turning on the device motor.

Resetting the drum counter

Click [Menu] [4. Device Information] [6. Resetting the drum unit]

Press the “Up” arrow [∧] and the resource of the drum unit for the device is again 100%.

Check

You can check if the Brother DCP-1512R cartridge has been reset to zero by printing the “Custom Settings” report. We press

The printouts show that the toner and drum unit are 100% resource. By the way, I periodically print this report, you will see that the Brother DCP-1512R imaging drum is running out, and you can replace it in time.

Let’s look at how to reset the counters for Brother HL-1110R, HL-1112R, DCP-1510R, DCP-1512R, MFC-1810R, MFC-1815R printers. THESE models use one cartridge, TN-1075, so the toner and drum counters are reset in the same way.

Reset Toner Counter

How to do this through the device menu. I do not know yet. You can reset the toner counter of the Brother DCP-1512R manually, in the truest sense of the word. The process is simpler than the Brother DCP-7057R model. No need to disconnect and poke with a screwdriver.

We take out the cartridge and divide it into two parts (a toner unit and a drum unit).

Insert the drum unit into the device.

Pulling paper out of the feed tray.

We put our hand through the paper feed tray and press the sensor or lever (located on the left).

    Hold and close the top cover.

As soon as we hear the engine noise, release the sensor and after 1 second press it again.

We hold until the device warms up and dies down.

  • Open the lid, take out the unit with the drum unit, assemble the cartridge, insert it into the device and print.

You may not be able to reset the counter of the Brother DCP-1512R printer right away. Try to repeat the process by pausing before releasing the sensor for about 1 second after turning on the device motor.

Resetting the drum counter

Click [Menu] [4. Device Information] [6. Resetting the drum unit]

Press the “Up” arrow [∧] and the resource of the drum unit for the device is again 100%.

Check

You can check if the Brother DCP-1512R cartridge has been reset to zero by printing the “Custom Settings” report. We press

The printouts show that the toner and drum unit are 100% resource. By the way, I periodically print this report, you will see that the Brother DCP-1512R imaging drum is running out, and you can replace it in time.

How to reset the toner counter on Brother printers DCP-l2500dr / l2540dnr, MFC-l2700dnr / l2700dwr worthy of similar

Use the printer control panel to reset the toner counter for Brother DCP l2500dr, l2700dnr, l27dnr, l2700dwr. I have to press certain buttons, in parallel I look at the built-in screen, agreeing with the notification.

All actions are simple, you can reset the drum or toner counter in one minute. In order not to require manual user intervention in the design of the cartridge, an additional detail has been added in the new models. a flag. When rotated, it will automatically dump data.

The instruction also applies to l2520dwr, l2540dnr, l2560dwr multifunctional devices.

Reset photo

The photo drum (photo drum) is one of the main components of a laser printer. Like a cartridge, it has its own resource. The drum is programmed from the factory to print a certain number of pages. When the counter reaches the maximum value, the message “Replace the drum unit” (or something similar) appears on the printer screen and printing is blocked.

There are two options for correcting the situation:

  • Or really make a replacement for a new photo roll;
  • Or reset to zero to continue printing.
  • Starts the printer and wait until the work of the mechanisms ends (the device will stop making noise):
  • Open the printer cover by pulling it towards you;
  • Press the “OK” button on the body when the question “Replace the drum?”.
READ  Q2612a Cartridge For Which Printers

Then I confirm the reset:

  • For Brother printers with numbers “25”, press the “” button;
  • On models with the first number “27” use the button “1”.

Close the cover and start printing any document. Printing should resume.

How to reset a cartridge

The reset algorithm is almost the same as the previous one. Zeroing will have to be done when the printer says “Replace cartridge”, “Out of toner” and other similar notifications on the built-in screen. Even after refilling the cartridge, the notification will remain, so you must reset the toner count.

  • Open the printer by pulling the cartridge access door;
  • Hold down the “Menu” button and wait on the display for the notification “Reset counter TNR-STD A”, Press the button;
  • Agree by clicking “OK”;
  • Confirm zeroing by pressing “” or “1” for series “25” and “27” respectively.

The printer will then accept confirmation and display a notification that the reset has started.

Start printing after exiting the menu (Stop / Exit button) and closing the cover.

You can learn more about zeroing by watching the video.

How to reset the toner counter for Brother cartridges

Brother TN-2080 / TN-2085 / TN-2090 / TN-2275.

This is how the “flag” looks like (see the image below), which we need to hob in order to reset the toner counter in the printer. To do this, Unscrew 2-3 screws (depending on the model) and remove the side “cheek” covering the reset mechanism.

Remove the two gears covering the center gear. Rotate the center gear to the position shown in the figure below so that the straight edge of the center part is vertically to the left.

Reinstall the two gears. The right gear should be in the petal position (protruding edge) down as shown in the figure.

Install the side panel. In total, after assembling the cartridge, make sure that the protruding tabs are facing down and the marker arrows are facing each other.

This procedure, sometimes, has to be repeated more than once, even with a new cartridge.

Resetting the Toner Counter Using the Machine Menu

The instructions for resetting the toner counter through the machine’s menu are only applicable for all-in-one printer Brother DCP-7055 / DCP-7057 / DCP-7060 / DCP-7065 / DCP-7070 and MFC-7360 / MFC-7860. The procedure must be performed if the “flag” on the cartridge has reset the toner counter in the printer.

  • Press the “Menu” button
  • Use the arrows to select “General settings” and click “OK”
  • Select “Replace Toner” with the arrows and press the “OK” button
  • Select “Continue” with the arrows and click “OK”
  • To exit the menu, press the “Clear” button.

You can only reset the toner counter through the printer menu once. In the future, you need to use the method of resetting the counter by cocking the “flags” on the cartridge.

Brother TN-1075

(Brother HL 1110R / 1112R, Brother DCP 1510R / 1512R, Brother MFC 1810R / 1812R)

1.Open the printer cover where the cartridge is installed.

Remove the cartridge from the printer,

Left only the drum part in the machine (Drum unit).

Press your finger on the reset sensor in the printer. The reset sensor is located on the left side of the printer; you can reach it through the input tray after removing all paper from it.

Close the printer cover.

Hold the gauge to start the printer engine.

After starting the engine, release the sensor, and after 1.5-2 seconds (no more!) Press it again and hold it to a complete stop of the engine.

Wait until the printer is ready.

Put the cartridge back in the drum unit.

Brother TN-2075, TN-2135, TN-2175

Insert the cartridge into the printer and turn on with the cover open.

Press the flags on the lever as shown in Fig. 2.

When the sensor is pressed, press the second sensor. the sensor for closing the lid Fig. 3.

After a few seconds, the printer will start scrolling the cartridge (you can hear it). As soon as this happens, depress the sensor flags, but do not touch the sensor cover.

Wait for the printer to be ready.

Press the cover sensor, close the cover.

The printer is ready to use.

Instructions for all-in-one printer:

1.Turn off the power, insert the cartridges, leave the cover open.

Detach lever 1 from the cover and insert it inside the all-in-one printer fig. 4.

Press sensor 2 and sensor 3 with a screwdriver Fig. 4 (2. new cartridge sensor, 3. lid closed sensor)

With 2 and 3 pressed, wait until the all-in-one printer starts spinning inside. At first you will hear a faint fan noise. And after a while. significantly more Strong noise of the scrolling mechanism.

1 second after the all-in-one printer started scrolling inside, release sensor 2, but not Press 3.

After the all-in-one printer stops spinning, release 3, attach lever 1 back and close the cover.

All-in-one printer is ready to work.

For an all-in-one printer, reset all counters, including the cartridge counter and drum cartridge counter:

  • Turn off the device.
  • Clamp the “Menu / Set” button and turn on the device.
  • The device boots up in service mode.
  • Enter “81”.
  • We get the message “Reset drum count”.
  • Click “Start”.
  • The message “Reset life count” appears.
  • Press “Start” again.
  • We leave the service mode, typed “96”, or “98”, or “99”.
  • Turn off the device, turn on.

How to reset the toner counter on Brother DCP-7057R printer

It is necessary to reset the Brother DCP-7057R toner counter if the machine displays “Replace Toner” or “Toner Low.” This message appears after installing a cartridge refill or when very little powder ink remains.

The device is equipped with a chip that keeps track of the number of sheets printed. This is how the toner level is determined. For example, it is programmed that after printing 1000 pages, work will be blocked with a notification about the need to replace the powder. But this is not always correct, because each sheet is filled with ink in different ways and the toner in the cartridge may still be enough to print a certain number of sheets.

In any case, it is better not to risk it and refuel the container. But this will not help remove the notification and make the printer work after refueling. It is imperative to make a reset so that the device removes the blockage and starts counting the ink consumption again.

How to reset yourself

Via the printer menu (software)

First, try to reset yourself through the built-in menu of the device.

  • Turning on the power to the printer.
  • You are waiting for the equipment to stop making noise and switch to operating mode.
  • Opening the cover on the front of the case.
  • Press the “Cancel” key on the case. The button may be called “Stop”, “Back” or “Clear” on different devices.

Hard reset

  • Including the device in the network. Waiting for the testing process to complete.
  • Opening the door on the case.
  • On the left side, find a lever, which disconnects and hide in the case.
  • Removing the refilled cartridge and divide it into two parts: the toner container and the photo roll.
  • Place the drum back into the machine, and the powder hopper is temporarily left aside.

Zeroing the drum unit

If there is damage on the surface of the photocell, it is not necessary to replace the shaft; to eliminate the error, simply reset the counter.

Clean the corotron (charge roller) before resetting. Move the blue slider from side to side, which is located on the cartridge. If that doesn’t fix the problem, try resetting the counter.

  • Including all-in-one printer.
  • Wait for the equipment to warm up and get ready for work.
  • Open the lid and click on “Clear”.
  • The screen should display the message “Have you replaced the drum unit?”.
  • Press the “Up” and “Yes” arrows alternately.
  • When the display reads “Accepted”, close the cover.
  • Restart the machine.

We reset both counters at once

  • Turn off the device.
  • Clamp the “Menu” key and simultaneously the “On” button on the all-in-one printer.
  • The message “MAINTENANCE” appears on the screen.
  • Look for the term at number 84 and click “Ok”.
  • When the inscription “PROCESS CHECK” appears, click on “OK”.
  • After displaying the inscription “PLZ POWER OFF / ON” I turn off the device.
  • Turning on Brother, “PROCESS CHECK” will appear on the screen.
  • Go to the subsection “RESET TONER COUNT” and confirm the reset of the cartridge by pressing “Ok”.
  • Return to the previous menu and, in order to reset the photo, go to the “RESET DRUM COUNT” menu and also confirm by pressing the “Ok” button.
  • Turn off all-in-one printer.
  • Clamp the “Menu” button again together with the inclusions.
  • When “MAINTENANCE” is written on the screen, go to “PROCESS CHECK” and with the “Ok” button activate the “CHEKER MODE OFF” option.
  • If the reset is successful, the display will show “PLZ POWER OFF / ON”.
  • Reload the technique and print the probe.
READ  Reset Counter On Brother Dcp 1610wr Printer

Resetting the counter on various Brother printer models

It’s no secret that all Brother printers, especially laser printers, have an installed chip-like protection, which in some models is located on a cartridge. Thus, manufacturers of equipment for printing are trying to fight with companies that provide users with refilling the toner cartridge. Indeed, due to the availability of such a service, the sale of original (new) cartridges is significantly reduced. But, if you look at the situation from the point of view of the user, then paying a lot of money for a new cartridge, which costs almost half the price of a new printer, does not make sense. Therefore, Brother laser owners often resort to such a procedure as clearing or zeroing the counter, which you can do yourself.

Why reset the counter

Trimming is the procedure for changing equipment settings. The protection itself operates according to the following principle:

  • The manufacturer installs a special meter in the system;
  • The chip counts the number of sheets used during printing, and, after the cartridge has run out, signals this to the user, block the machine.

Each cartridge has its own resource. There are toner containers designed for 2,500 sheets, and sometimes. for 1,000 sheets. The chip is programmed according to the number of sheets. After exceeding the print limit, the message “Replace consumables”, “Toner empty” appears, or the indicator simply blinks. But, although you can add new toner, the chip will still consider that the cartridge is empty, and will not allow the machine to work. To get rid of this problem, a method was devised to reset the counter.

Resetting the TN-1075 cartridge

TN-1075 cartridge is quite common in Brother laser printers. It is installed, for example, in such models of devices as: DCP 1510r, dcp 1512r, MFC-1810R (1815R), HL-1110R (1112R).

To reset the counter on a TN-1075 cartridge, there are 2 methods, which are used depending on whether you have a starting model that does not have a crescent-shaped gear, or you have already purchased a replacement one.

Starter cartridge

So, if a message appeared in the brother printer: “Change toner”, then proceed as follows.

  • Empty the paper tray and remove the module from the machine.
  • Division cartridge from drum unit, pressed the blue key case.
  • Put the drum unit back into your brother printer. On the left side of it you can see a hole from which you can see the reset button.
  • There is only one way to click on this checkbox. It will only be possible to reach it through the tray, in which paper is put. You must remember where the checkbox is, as the reset will happen when the lid is closed.
  • Knowing where the button is, press it and close the cover of the unit. Don’t be afraid that something will happen to your finger. there are moving parts in this place. So, after closing the lid, the engine will turn on. As soon as you hear it work, immediately release the button and after 1 second press it again. Wait in this position until the engine stops.
  • You can tell that the operation was successful by the blinking green LED. If this does not happen, then repeat all over again.
  • Insert the cartridge into the drum unit. This completes the resetting of the counter in the brother printer.

Purchased Toner Cartridge TN-1075

Besides the fact that the counter can be reset with a button, there is another easy way to reset the brother printer.

  • Detach the cartridge from the drum unit and unscrew the side cover from the side where the gears are visible.
  • Remove the cover carefully to prevent the gears from spilling out. You only need to remove one gear, as shown in the following figure.
  • Next, you will see a crescent-shaped gear that needs to be returned all the way, as shown in the photo below.
  • The gear previously removed can now be reinserted.
  • Close the cover carefully so that the crescent-shaped gears DO NOT move.
  • Screw on the cap and insert the cartridge into the drum unit.

After all THESE actions, place the module in the printer.

Zeroing algorithm for laser models HL-2130R, HL-2132R, DCP 7055r and DCP 7057r

There are also 2 ways to reset the page counter in the HL-2130R (hl 2132R) and DCP 7055r (7057r) laser models: software and hardware.

Software way to zero the printer HL-2130R (2132R)

To soft reset the counter on your brother printer, do the following:

  • Turn on the device (after turning on you will hear the noise of the drive)
  • After the noise disappears, open the cover located in front of the unit;
  • Disconnect the device;
  • Press the “Go” button and Do not release it until the unit turns on again (the “ready” indicator should NOT be on)
  • Lower the “Go” key;
  • Press the “Go” key twice again;
  • Click on “Go” 5 times in a row;
  • Close the cover (front).

The “ready” indicator now lights up steadily. After THESE manipulations and overloading the machine, the Brother hl 2130r (2132) laser can be considered zeroed and ready to work.

Software reset all-in-one printer DCP 7055r

To reset the counter programmatically in the all-in-one printer dcp 7055r, follow the steps below:

  • Press the “Menu” key;
  • Then select “General settings”, then click on “OK”;
  • At the next step, select “Change toner” and again “OK”;
  • Using the arrows on the control panel, select “Continue” and press “OK”;
  • To exit this menu press “Clear”;
  • Counter has been reset.

Zeroing DCP 7057r by software

Zeroing the MFC DCP 7057r is slightly different from DCP 7055r:

  • Turn on the all-in-one printer and wait for the mechanics to quiet down;
  • After that, open the cover located in front of the device;
  • Click on the “Cancel” button (“Back” or “Stop”)
  • Press the “Start” button;
  • Press the up arrow key followed by the down arrow key several times until you see 2 zeros (00) on the display
  • Press “ok” and the front cover can be closed.

In the case when these 2 methods did not help, then you can reset through the system menu all-in-one printer.

  • First check that your all-in-one printer is turned off.
  • Press and hold the Menu key.
  • Turn on the device while holding down the.
  • After you see a blinking inscription on the screen of the device, Release the “Menu” key.
  • Wait a while until the word “MAINTENANCE” is displayed on the screen.
  • Using the arrow keys, you need to find point 81, then confirm the selection by clicking on “OK”.
  • The screen will display the inscription “RESET DRUM COUNT” After pressing the “Start” button, the message will change to “RESET LIFE COUNT”. Press “Start” again.
  • Using the arrow keys, you need to select already item 96 and confirm with the “OK” key.
  • Let’s reboot the unit. To do this, you need to turn it off and turn it off again. This completes the resetting of the counter.

Hardware method of zeroing

You can also reset the all-in-one printer in hardware. To do this, proceed as follows.

  • After the all-in-one printer displays “Replace Toner”, pull the cartridge out of the machine.
  • On the starter cartridge you will see a black plug with a small stop, which must be cut off with a knife.
  • The next step is to remove the spring with the flag.
  • The spring should not be thrown away. You will install it if you want to change the starter cartridge for a purchased one.
  • Next, insert the cartridge into the machine, release the lever and hide (drown) it in the all-in-one printer.
  • Using a match or a screwdriver, you need to press the sensor, the case is located, which is responsible for the closed cover.
  • When you hear the mechanics work, press 2 times in the flag with a screwdriver. It is necessary to press so that you can make 2 clicks within 4 seconds. If unsuccessful, you can try again.
  • After the counter has been successfully reset, you will see an inscription on the screen (see photo below).
  • Now you need to print a test page that contains information about the status of the toner and drum unit. To do this, press the “Menu” key, select “Device Information” and “User Settings”. Confirm your choice by pressing the “Start” button.
  • If you did everything correctly, a test page will print.

At this stage, the all-in-one printer can be considered completely ready for work.