How To Reset The Cartridge After Refilling Brother

Soft toner reset

Developers create additional maintenance functions for their equipment. Among them is a paint dump tool. It runs only through the built-in display, so it is NOT suitable for all users. If you are the lucky owner of a device with a screen, follow these steps:

  • Turn on the all-in-one and wait for it to be ready to go. When the “Wait” message is displayed, you don’t need to press anything.

How To Reset The Cartridge After Refilling Brother

Next, open the side cover and click on the “Clear” button.

On the screen you will see a question about replacing the drum, to start the process, click on “Start”.

Close the side cover if the corresponding message appears on the screen.

Now you can go to the menu, move around it using the arrows to get acquainted with the state of the counter at the moment. If the operation was successful, its value will be 100%.

As you can see, zeroing paint through a software component is not difficult. However, not everyone has a built-in screen, and this method is not always effective. Therefore, we recommend that you pay attention to the second option.

Detailed instructions for zeroing

First, it should be said that resetting the brother hl 1110 counter is needed when office equipment, having printed a certain number of pages and thus, having reached a certain limit, stops its work. Refilling the starter consumable with brother toner alone will not be enough in this case, because Unlike purchased cartridges, they have a so-called N. Reset flags. In this case, do the following:

  • First of all, you should remove the paper and carefully open the cover of the device.
  • Now carefully remove the drum cartridge from the inside of the device along with the toner cartridge.
  • In the next step, Remove the toner cartridge from the drum cartridge (use the button located on the consumable itself). Then insert the first item into the printer. THOSE. You must return only the housing base to the printer.
  • Pay attention to the left side. there you should notice a button that is specifically designed to reset the cartridge counter.

    To use this button, first try to extend your hand using the hole in the paper tray. As soon as you manage to do this, hold down this button with your finger.

All in all, as you can see, resetting the toner counter for the brother hl 1110r is not that difficult and time consuming. After the performed actions, which were described above, the following two options are possible:

    If all the actions were performed correctly, the printing device will not “peep” and no error will be displayed on its display. In this case, you can safely pull out the cartridge base from the device, insert the toner, and then send the newly collected consumables back to the printer. can use your brother for next refill.

It should be added that beginners in this business may need not one or two attempts to achieve success, but three or four or even more. So be sure to be patient.

See about zeroing Brother 1110

Reset ALGorithm

1 sec press the button again and hold

How to reset the toner counter for your Brother printer

The following instructions will work best for most Brother printing machines as they are all SIMilar in design and quite often contain TN-1075 Cartridge. We’ll look at two ways. The first is suitable for users of MFPs and printers with a built-in screen, and the second is universal.

How to renew a cartridge after refilling brother

Almost all models of printers and MFPs from Brother are equipped with a special built-in mechanism, which keeps track of printed pages and blocks ink supply after the expected end. Sometimes, users who have refilled a cartridge are faced with a problem in which the toner was not detected or a notification appears asking to replace it. In this case, you must reset the ink counter to continue printing. Today we’ll show you how to do it yourself.

Manual reset

The Brother cartridge has a reset sensor. It needs to be activated manually, then the update will be successful. To do this, you need to independently remove the components and perform other actions. The whole procedure looks like this:

  • Turn on the printer, but do not connect to the computer. Be sure to remove the paper if installed.
  • Open the top or side cover to access the cartridge. Do this action taking into account the design features of your model.

Remove the cartridge from the equipment by pulling it toward you.

Disconnect the cartridge and drum unit. This process is intuitive, you just need to remove the latches.

Insert the drum part back into the device as it was previously installed.

The zero sensor will be located on the left side inside the printer. You need to advance your hand through the paper feed tray and press this sensor with your finger.

Hold it and close the lid. Expect the start of the work of the apparatus mechanisms. Then release the sensor for a second and press again. Hold until engine stops.

READ  How To Reset Brother Dcp 1510r Printer

It remains only to mount the cartridge back into the drum part and you can start printing.

If, after a two-way reset, you still receive a notification that no toner was found or ink has run out, we recommend checking the cartridge. Refuel if necessary. You can do this at home, using the instructions attached to the device, or contact the service center for help.

We have covered two available methods to reset the toner counter on Brother printers and MFPs. It should be borne in mind that some models have a non-standard design and use cartridges of the second format. In this case, the best solution would be to use the services of service centers, since physical intervention in the components can provoke device malfunctions.

Reset Toner Counter for Brother Printers

The other day a problem with the Brother MFC-1810R printer arose in relatives. After refilling the starter cartridge, the printer requires replacing the toner. To solve this problem, the printer needs to reset the toner counter. Since the TN-1075 cartridge is distributed among Brother machines, the instruction described here will work for DCP-1510R, DCP-1512R, HL-1110R, HL-1112R, MFC-1810R, MFC-1815R.

So, if your printer displays the “Change Toner” error, then you need to do the following sequence of actions:

  • Remove the cartridge and paper from the printer.
  • Remove the toner from the housing. To do this, use the special lever on the cartridge.
  • Insert only the base of the housing into the printer. On the left you will see a button to reset the counter.
  • Insert your hand through the paper tray, feel and hold the button with your finger.
  • Close the cover through which the cartridge is inserted.
  • Wait for the mechanism inside the printer to spin. As soon as it spins, release the counter reset button for 1-2 seconds (no more), then press it again until the mechanism inside the printer stops.
  • Further two options are possible:
  • If the printer clicks and displays an error “Change toner”, then you could not catch the correct moment in the previous step (step 6). Go back to step 1 and Do all the steps again (I was able to reset the toner counter correctly only from the fourth time).
  • If you did everything correctly, the device will not peep, the printer display will display the “Change toner” error. Now pull the cartridge base out of the printer, insert the toner, and then put the Assembled cartridge back in. The printer will now work until the next cartridge refill.

Soft toner reset

Developers create additional maintenance functions for their equipment. Among them is a paint dump tool. It runs only through the built-in display, so it is NOT suitable for all users. If you are the lucky owner of a device with a screen, follow these steps:

  • Turn on the all-in-one and wait for it to be ready to go. When the “Wait” message is displayed, you don’t need to press anything.

Next, open the side cover and click on the “Clear” button.

On the screen you will see a question about replacing the drum, to start the process, click on “Start”.

Close the side cover if the corresponding message appears on the screen.

Now you can go to the menu, move around it using the arrows to get acquainted with the state of the counter at the moment. If the operation was successful, its value will be 100%.

As you can see, zeroing paint through a software component is not difficult. However, not everyone has a built-in screen, and this method is not always effective. Therefore, we recommend that you pay attention to the second option.

How to reset the printer after refilling the cartridge brother. How to reset the toner counter for your Brother printer

The following instructions will work best for most Brother printing machines as they are all SIMilar in design and quite often contain TN-1075 Cartridge. We’ll look at two ways. The first is suitable for users of MFPs and printers with a built-in screen, and the second is universal.

How to clear the toner replacement message for TN-2075 / TN-2135 / TN-2175

Printer instruction:

  • Insert the cartridge into the printer and turn on with the cover open.
  • Push the lever flags

.3. When the sensor is pressed, press the second sensor. the sensor for closing the lid

After a few seconds, the printer will start scrolling the cartridge (you can hear it). As soon as this happens, depress the sensor flags, but do not touch the sensor cover.

Wait for the printer to be ready.

Press the cover sensor, close the cover.

Instructions for MFP:

1.Turn off the power, insert the cartridges, leave the cover open.

Detach lever 1 from the cover and insert it inside the MFP

Press sensor 2 and sensor 3 with a screwdriver Fig. 4. (2. new cartridge sensor, 3. lid closed sensor)

With 2 and 3 pressed, wait until the MFP starts spinning inside. At first you will hear a faint fan noise. And after a while. much more loud noise of the mechanism scrolling.

1 second after the MFP started scrolling inside, release sensor 2, but not Press 3.

After the MFP stops spinning, squeeze out 3, attach lever 1 back and close the lid. MFP ready to go.

How to clear the Toner Replacement message for TN-2335 / TN-2375 cartridges

  • Open the front cover;
  • Press and hold the “Menu” button until the message “Reset TNR-STD A counter” appears on the screen;
  • Press the “OK” button;
  • Select “Reset” with the up arrow;
  • Press the Stop / Exit button and close the lid.
READ  How To Install A Printer On A Laptop Without A Disk

For all Brother laser printers and MFPs

This article is to self-reset the toner replacement message. The message might look like: Replace toner cartridge, Replace toner, Toner low, Replace toner cartridge.

Perhaps you have a Brother starter cartridge, which does not have a mechanism for resetting the cartridge counter, or the mechanism did NOT work after refilling. Also, the article can be useful because you can reset the message about the need to replace the toner cartridge, thereby printing the remaining toner in the cartridge to the end.

Since there are several types of Brother cartridges, like the machines themselves, the ejection mechanism is different.

How to clear the toner replacement message for Brother printers and MFPs?

How to reset the message about replacing the toner cartridge TN-2235 / TN-2275 / TN-2290 / TN-2090 / TN-2080

  • Open the printer cover.
  • Press the “CLEAR” button on the printer (CLEAR / back arrow button).
  • Press the “Start” button (START / button, highlighted with a green stripe).
  • Press quickly or. (up and down arrow buttons).
  • Set on the screen 00 (two zeros) on the counter, Using the keys /. (up / down).
  • Press the “OK” button (between the up and down buttons).

How to clear the toner replacement message for TN-1075 / TN-1095 cartridges

  • We take out the cartridge. We leave only the drum cartridge in the device (where the drum is)
  • We put our hand through the paper tray and clamp the reset flag. It is located on the left side of the drum cartridge in the rectangular hole (pictured)
  • Keeping the flag pressed down, close the lid.
  • As soon as the engine starts (characteristic buzzing), I release the flag and after 1.5. 2 seconds it is clamped again. We hold until the engine stops.
  • We see what the device writes on the scoreboard.
  • If “Replace Toner” lights up again, repeat the procedure.
  • If it is ready, Install the cartridge back and use.

How to clear the message about replacing the toner cartridge TN-2085

  • First, turn on the printer, then gently open its front cover.
  • Turn off the printer with the cover open.
  • Now press the “GO” button and hold it while turning on the device.
  • Wait until all 3 indicators light up. in addition to “READY”.
  • If you have done everything correctly, you can release the “GO” button.
  • Press on “GO” and release it. repeat this twice.
  • Wait a short pause, about 1.5-2 seconds, then press and release the same button 5-6 times.
  • If the “Toner” light stops lighting, then congratulations. the toner counter has cleared and you can safely print.
  • In the end, all that remains is to close the front cover of the printer, turn it off and on. Be sure to print some test pages.

How to clear the message about replacing toner and drum unit for color 9020/3140/3170/9330

If an error occurs in the Brother 9020 printer, open the top cover, press and hold for about 2-3 seconds. In the list that opens, we select a cartridge or drum of the color you need.

For the Brother 3140 printer, to eliminate these errors, it will be correct to slightly open the top cover of the turned on printer and press the “Secure” and “Сancel” buttons at the same time. Having selected the color cartridge or imaging drum required for reset, press “OK” and “Up”.

The correct procedure for resolving toner and imaging drum errors for the Brother 3170 Color Printer is to open the top cover and press the Secure and Cancel buttons on the printer at the same time. In the reset menu that appears on the display of the printing device, we select the cartridge of the color you need or the drum unit. Then press the “OK” and “Up” buttons.

To resolve auto products errors related to replacing toner or drum unit in Brother 9330 multifunctional color printer. Do the following: Open the top cover, press and hold for about 2-3 seconds. Select the drum or cartridge of the desired color from the menu list.

How to reset the counter on the Brother dcp 1512r printer

Resetting the toner counter The Brother DCP 1512R helps you get rid of the “Replace Toner” error even when it has been refilled or replaced with a new one. Explain how to deal with the auto goods problem yourself, and mention in resetting the drum counter.

How to reset the toner counter Brother DCP 1512R

Toner zeroing is performed manually, and you do NOT need to use a screwdriver or other tools. The instructions described below are suitable for models of the HL 1110R / 1112R, DCR 1510R / 1512R series and two machines from the MFC line. 1810R / 1815R. All these MFPs use the same TN-1075 container and have a SIMilar case structure.

Anyone with experience in replacing cartridges with an MFP can reset the counter Using the quick start guide:

  • Press the power key on the printer;
  • Take out the drum cartridge to separate it into toner and drum unit;
  • Place the second element back into the body;
  • In the tray, feel the black flag, which is closer to the left edge, and squeeze it;
  • After close the cover, wait for the engine to make noise, lift your finger off the lever for 2 seconds and clamp it again;
  • After the noise stops, release your finger and assemble the drum cartridge;
  • This should reset the printer to zero.

Inexperienced users are waiting for Step-by-step instructions with a detailed description of each action.

  • Connect the Brother DCP 1512R to an electrical outlet, and turn it on through the button on the case.
  • Lift the front cover to remove the print cartridge, which consists of a toner module and a drum unit. They are marked TN / DR-1075.
  • Press down on the blue lever in the lower right corner to disengage both modules. Attach the drum unit marked DR-1075 back to the printer body.
  • Temporarily remove any paper in the tray.
  • Pass your hand through the opening of the tray, which will allow you to reach with your fingers the cartridge located inside the case.
  • On the left is a black lever / flag. I felt it with my finger (located in the notch), hold it and Don’t let go.
  • Close the front cover with your free hand.
  • After the appearance of the noise, which marks the start of the MFP operation, you will need to unplug your finger from the lever, and then press it down after 2 seconds.
  • As the machine stops making sounds, Release your finger and remove your hand.
  • Reopen the front cover, remove the cartridge from the housing.
  • Insert the toner container into it and place it in the machine.
  • Try to start the printer.
READ  How To Connect Pantum Printer Without Disk

Sometimes it is recommended to reboot the machine additionally if the print attempt is NOT successful or the MFP reports an error again. Try repeating the process 1-2 more times. If the problem persists and the capacity is full, reset the drum counter as described below.

How to reset the drum counter Brother DCP 1512R

After updating the cartridge capacity, experts recommend overthrowing the counter of the number of prints, otherwise the “Replace toner” error may appear on the MFP display. Another reason to reset the drum counter is the device’s actual print capacity of the above 10,000 prints by default. If, after the marked number of prints, the quality of the documents remains acceptable, then:

  • Connect the device to the network and press the power button;
  • Click on “Menu”;
  • Use the “Up / Down” control keys to find the “Device Information” section. the fourth in the account;
  • Click on the “OK” button;
  • Navigate the menu using the Up key until the sixth section, “Reset” appears. Photob. “;
  • Hold the “OK” button for about 5-7 seconds
  • Click the Up key once, the display should show 100% drum life. The device will enter “sleep mode”.

To make sure the reset was successful, print a detailed print cartridge status report:

  • Turn on the MFP with the “Enable” button;
  • Visit “Menu”;
  • Scrolling through the sections, Until “Device Information” appears, click “OK”;
  • Then select “Custom settings” and again Click on “OK”;
  • It remains to select “Start” and start printing.

A printout appears in the tray with detailed information about the life of the assembly. Toner refill and drum life information will be displayed on a scale from 0 to 100%.

Resetting Counters on Brother DCP 1512R Takes a few minutes before the machine should be back online. If the display continues to receive the “Replace Toner” error, it makes sense to reset the drum counter and prompt for a detailed printout of the remaining printer life.

Set up your computer

Advice on setting up computers, gadgets, setting up and installing programs, tablets, phones, smartphones. Solving computer problems.

Brother dcp-7060dr. Resetting the tn-2275 cartridge after refueling

  • Remove the cartridge. The white thick arrow indicates the lever on the white “lamb”, which we need to rotate 180 degrees in step 3
    Starting position
  • Remove the two screws. Remove the cover. The same lever is marked with a thick white arrow, and thin black arrows. The places where the bolts were unscrewed
    The removed cover on the cartridge. The lamb looks down
  • Expand the white lamb 180 degrees
    The removed cover and the lamb are already turned upward with the lever
  • Screw back the cover and two bolts from item 2. Compare the bottom photo with photo 1, you can see that the white lever looks up
    The lid is screwed on and the lamb looks up
  • This cartridge is in drama. Removing the cartridge from the dram and inserting only the dram into the printer. The cartridge with which we worked before while resting.
  • Something grips the lid closing sensor. In the photo below, a white arrow points to this sensor. And he pinch with tweezers
    Clamped cover open sensor
  • I removed the return spring that holds the MFP cover. In this photo, the spring has already been removed and is indicated by a red arrow. This photo is taken from the site Repair of printers and copiers
    The retracted spring that holds the lid
  • Turn on the printer. And as soon as the engine starts to work (audible by the noise), we begin to periodically press-Squeeze the lever. So that during the operation of the engine, press about 3 times. In the photo below, the lever is indicated by a white arrow. And on the left, a screwdriver stretches towards him, with which I pressed on him
    The lever that we press
  • Returning the cartridge to the dram from step 5 and pushing it all into the MFP
  • We release the cover closing sensor from item 6. I just pull out my tweezers.
  • Return the return spring from item 7
  • Close the front cover. The MFP should hum for a while. If everything is done correctly, the standard info will appear on the digital display of the MFP. If wrong, then the error message.

The printer started working in this way the first time.

All cases of resetting cartridges you can see in the “Reset cartridges” section of this blog.