How to reset toner on a brother printer

Brother Printer Toner Reset Guide

Brother printing device manufacturers equip their equipment with a security chip that locks the printer when the cartridge reaches its end of life. As a consequence, it is difficult to reuse the ink tank after refilling. Since the cost of consumables is quite high, machine users have to reset the toner counter.

Zeroing the HL-2130R (2132R) device by software

How to reset the counter of the HL-2130R or HL-2132R using the software method? Simple actions are envisaged:

  • First of all, the Brother HL-2132R printer must be turned on and wait until it dies down after preliminary preparation for work.
  • Open the front cover, then turn off the device.
  • Press the “Go” button and hold until the Brother HL-2132R (HL-2130R) machine is turned on.
  • After releasing the key, you should wait until the indicators go out, and then press it again 2 times.
  • After 4-5 seconds, you must press “Go” 5 times in a row. As a result, the “Error” indicator should light up.
  • The final step is closing the lid Brother HL-2132R.

reset, toner, brother, printer

If you do everything correctly, the Brother HL-2132R printer will reset, that is, the toner counter will be reset.

How to reset the DCP-7057R

If the Brother DCP-7057R printer refuses to work, informing that a new cartridge needs to be installed, you can reset the settings using the software method.

Resetting the counter on a Brother printer is done in several steps:

  • It is necessary to turn on the device and wait for it to die down.
  • The cover on the front of the printer is opening.
  • One of the keys is pressed. “Cancel”, “Stop” or “Back”.
  • Next, you need to press “Start”.
  • Press “Up” once, then press “Down” until the display shows two zeros.
  • At the end, press “OK” and close the lid.

How to reset the HL-1110R device

The task of the counter built into the printer is to keep track of the number of sheets that have been used. Toner containers have their own limits. When it is exceeded, the printer displays information about the need to replace the consumable. Even after refilling the cartridge, the device will perceive it as empty.

To solve the problem, you will need to buy a new ink tank, but many use an effective method. resetting the toner counter on a Brother printer. It will be useful to find out how to reset the settings yourself, depending on the device model.

If you have a Brother HL-1110R, DCP-1512R, MFC-1810R machine, reset the toner counter as follows:

  • After removing the paper, the cover opens.
  • The cartridge is removed and after pressing the button located on the right side, the toner is removed.
  • The base (drum-unit) comes back.
  • On the left side of the HL-1110R there is a button that is designed to reset the counter of the Brother HL-1110R printer. You can only get it through the tray.
  • Putting your hand through the hole, you must press the button to reset the counter settings.
  • Without releasing the keys on the HL-1110R or DCP-1512R, close the cover and wait for the mechanism inside the Brother printer to rotate. As soon as this happens, the finger is removed, and after a second the key will need to be pressed again.
  • The key of the device HL-1110R, DCP-1512R must not be released until the engine stops working.

Resetting the Brother HL-1110R printer can be considered successful if, after the steps taken, the machine does not display an error message. The toner is inserted back into the substrate to perform the required tasks.

It is not always possible to zero the Brother HL-1110R or DCP-1512R printer the first time. The success of the operation depends on following the instructions exactly and on how quickly you can react at the right time. Therefore, if the device continues to report the need to replace the cartridge, you will need to repeat all the steps again.

DCP-7057R Hardware Zeroing Method

To reset the DCP-7057R laser device, you can use the hardware method:

  • If the display shows “Replace Toner”, you need to remove the cartridge from the machine. Before doing this, you must turn on the device and open the lid.
  • The cartridge is divided into components. toner and drum unit, after which the second element is put back.
  • Opening sensor is clamped with a screwdriver.
  • Next, you need to hold down the flag and press it twice for 4 seconds to simulate the presence of an inkwell. If the attempt is unsuccessful, repeat it.
  • Holding the checkbox, you should wait until the device dies down, after which the screwdriver is removed, and the cartridge is assembled and installed in place.

After resetting the printer, you can use it for its intended purpose.

To correctly reset the settings of the printing device, you must take into account its model and strictly follow the instructions.

How to reset the toner counter on Brother printers DCP-l2500dr / l2540dnr, MFC-l2700dnr / l2700dwr and others

Use the printer control panel to reset the toner counter for Brother DCP l2500dr, l2700dnr, l27dnr, l2700dwr. It is necessary to press certain buttons, while looking at the built-in screen, agreeing with the notifications.

All actions are simple, you can throw off the drum or toner counter in one minute. In order not to require manual user intervention in the design of the cartridge, an additional detail has been added in the new models. a flag. When rotated, it will automatically dump data.

The instruction also applies to l2520dwr, l2540dnr, l2560dwr multifunctional device models.

Resetting the photo roll

The drum (photodrum) is one of the main components of a laser printer. Like a cartridge, it has its own resource. The drum is programmed from the factory to print a certain number of pages. When the counter reaches the maximum value, the message “Replace the drum unit” (or something similar) appears on the printer screen and printing is blocked.

  • or really make a replacement for a new photo roll;
  • either do zeroing to continue printing.
READ  How to Connect Printer to Laptop with Wire

If solid black stripes (or wavy ones) are visible along the edges of the sheet, then the drum has really worked itself out. The sensitive shaft cover has been damaged. Then it is better to replace the photo roll with a new one in order to print blank sheets. Otherwise, with normal print quality, it makes no sense to make a replacement.

  • start the printer and wait for the mechanisms to end (the device will stop making noise):
  • open the printer cover by pulling it towards you;
  • press the “OK” button on the body until the question “Replace the drum?” appears on the display.
  • for Brother printers with numbers “25”, press the “” button;
  • on models with the first number “27” the button “1” is used.

Close the cover and start printing any document. Printing should resume.

How to reset a cartridge

The reset aLGorithm is almost the same as the previous one. Zeroing will have to be done when the printer says “Replace toner cartridge”, “Out of toner” and other similar notifications on the built-in screen. Even after refilling the cartridge, the notification will remain, so you need to reset the toner count.

  • Open the printer by pulling the cartridge access door;
  • hold down the “Menu” button and wait on the display for the notification “Reset counter TNR-STD A”, press the button;

The printer will then accept confirmation and display a notification that the reset has started.

Start printing after exiting the menu (Stop / Exit button) and closing the lid.

You can learn more about zeroing by watching the video.

How to reset the message about replacing the toner cartridge TN-2235 / TN-2275 / TN-2290 / TN-2090 / TN-2080

  • Open the printer cover.
  • Press the CLEAR button on the printer.
  • Press the “Start” key (START / button, highlighted with a green stripe).
  • Press quickly or. (up and down arrow buttons).
  • Set on the screen 00 (two zeros) on the counter using the keys /. (up / down).
  • Press the “OK” button (between the up and down buttons).

How to clear the toner replacement message for TN-1075 / TN-1095 cartridges

  • We take out the toner cartridge. We leave only the drum cartridge in the device (where the drum is)
  • We put our hand through the paper tray and squeeze the reset flag. It is located on the left side of the drum cartridge in the rectangular hole (pictured)
  • Keeping the flag pressed down, close the lid.
  • As soon as the engine starts (characteristic buzzing), release the flag and after 1.5. 2 seconds, hold it down again. We hold until the engine stops.
  • We look at what the device writes on the scoreboard.
  • If “Replace Toner” lights up again, repeat the procedure.
  • If it is ready, install the toner cartridge back and use.

How to clear the Toner Replacement message for TN-2335 / TN-2375 cartridges

  • Open the front cover;
  • Press and hold the “Menu” button until the message “Reset TNR-STD A counter” appears on the screen;
  • Press the “OK” button;
  • Select “Reset” with the up arrow;
  • Press the “Stop / Exit” button and close the lid.

For all Brother laser printers and MFPs

This article is for self-resetting the message about the need to replace the toner. The message might look like: Replace toner cartridge, Replace toner, Toner low, Replace toner cartridge.

Perhaps you have a Brother starter cartridge, which does not have a mechanism for resetting the cartridge counter, or after refilling the mechanism did not work. Also, the article can be useful because you can reset the message about the need to replace the toner cartridge, thereby printing the remaining toner in the cartridge to the end.

Since there are several types of Brother cartridges, like the machines themselves, the ejection mechanism is different.

How to clear the toner replacement message for Brother printers and MFPs?

How to clear the message about replacing the toner cartridge TN-2085

  • First, turn on the printer, then gently open its front cover.
  • Turn off the printer with the cover open.
  • Now press the “GO” button and hold it while turning on the device.
  • Wait until all 3 indicators light up. in addition to “READY”.
  • If you have done everything correctly, you can release the “GO” button.
  • Press “GO” and release it. repeat this twice.
  • Wait a short pause, about 1.5-2 seconds, then press and release the same button 5-6 times.
  • If the “Toner” light stops lighting, then congratulations. the toner counter has cleared and you can safely print.
  • In the end, all that remains is to close the front cover of the printer, turn it off and on. Be sure to print some test pages.

How to clear the toner replacement message for TN-2075 / TN-2135 / TN-2175 cartridges

  • Insert the cartridge into the printer and turn on with the lid open.
  • Press the flag lever

.3. While the flag sensor is pressed, press the second sensor. the sensor for closing the lid

After a few seconds, the printer will start spinning the cartridge (you will hear it). As soon as this happens, depress the flag sensor, but do not touch the cover sensor.

Wait for the printer to be ready.

Press the cover sensor, close the cover.

1.Turn off the power, insert the cartridges, leave the cover open.

Detach lever 1 from the cover and insert it inside the MFP

Use a screwdriver to press sensor 2 and sensor 3 Fig. 4. (2. new cartridge sensor, 3. lid closed sensor)

With 2 and 3 pressed, wait until the MFP starts spinning inside. At first you will hear a faint fan noise. And after a while. a significantly stronger noise of the mechanism scrolling.

1 second after the MFP starts scrolling inside, release sensor 2, but do not release 3.

After the MFP stops spinning, squeeze 3, attach lever 1 back and close the lid. MFP ready to go.

Brother TN-1075

(Brother HL 1110R / 1112R, Brother DCP 1510R / 1512R, Brother MFC 1810R / 1812R)

READ  Printer Status Unavailable Check Connection

1.Open the printer cover behind which the cartridge is installed.

leaving only the drum unit in the device (Drum unit).

Press your finger on the reset sensor located in the printer. The reset sensor is located on the left side of the printer; you can get it through the input tray after removing all paper from it.

Hold the sensor until the printer engine starts.

After starting the engine, release the sensor, and after 1.5-2 seconds (no more!) Press it again and hold it until the engine stops completely.

Wait until the printer is ready.

Put the toner cartridge back in the drum unit.

Resetting the Toner Counter Using the Machine Menu

The instructions for resetting the toner counter through the machine’s menu are only applicable for Brother DCP-7055 / DCP-7057 / DCP-7060 / DCP-7065 / DCP-7070 and MFC-7360 / MFC-7860 MFPs. The procedure must be performed if the “flag” on the cartridge did not reset the toner counter in the printer.

  • press the “Menu” button
  • use the arrows to select “General settings” and press the “OK” button
  • select “Replace Toner” with the arrows and press the “OK” button
  • select “Continue” with the arrows and click “OK”
  • to exit the menu, press the “Clear” button.

You can only reset the toner counter through the printer menu once. In the future, you must use the method of resetting the counter by cocking the “flag” on the cartridge.

How to reset the toner counter for Brother cartridges

Brother TN-2080 / TN-2085 / TN-2090 / TN-2275.

This is how the “flag” looks like (see the image below), which we need to cock in order to reset the toner counter in the printer. To do this, unscrew 2-3 screws (depending on the model) and remove the side “cheek” covering the reset mechanism.

Remove the two gears covering the center gear. Rotate the center gear to the position shown in the picture below so that the straight edge of the center section is vertical to the left.

Reinstall the two gears. The right gear should be in the “petal” position (protruding edge) down as shown in the figure.

Install the side panel. As a result, after assembling the cartridge, make sure that the protruding “flag” petal is facing down and the marker arrows are facing each other.

This procedure, sometimes, you have to repeat more than once, even with a new cartridge.

Brother TN-2075, TN-2135, TN-2175

Insert the cartridge into the printer and turn on with the lid open.

Press the flag lever as shown in Fig. 2.

When the flag sensor is pressed, press the second sensor. the cover close sensor Fig. 3.

After a few seconds, the printer will start spinning the cartridge (you will hear it). As soon as this happens, depress the flag sensor, but do not touch the cover sensor.

Wait for the printer to be ready.

Press the cover sensor, close the cover.

Instructions for MFP:

1.Turn off the power, insert the cartridges, leave the cover open.

Disconnect lever 1 from the cover and insert it inside the MFP Fig. 4.

Press sensor 2 and sensor 3 with a screwdriver Fig. 4. (2. new cartridge sensor, 3. lid closed sensor)

With 2 and 3 pressed, wait until the MFP starts spinning inside. At first you will hear a faint fan noise. And after a while. a significantly stronger noise of the mechanism scrolling.

1 second after the MFP starts scrolling inside, release sensor 2, but do not release 3.

After the MFP stops spinning, squeeze 3, attach lever 1 back and close the lid.

For MFPs, reset all counters, including the toner cartridge counter and the drum cartridge counter:

  • Turn off the device.
  • Press the “Menu / Set” button and turn on the device.
  • The device boots up in service mode.
  • Enter “81”.
  • We get the message “Reset drum count”.
  • Click “Start”.
  • The message “Reset life count” appears.
  • Press “Start” again.
  • We exit the service mode by dialing “96”, or “98”, or “99”.
  • Turn off the device, turn on.

How to reset toner on a brother printer

To reset the toner counter for monochrome printers manufactured by Brother, an aLGorithm is used that is quite complex for an ordinary user to understand. Therefore, a hardware implementation of the toner counter reset button was developed. As an example, we took the Brother HL-2132R, which uses cartridges of a small nominal capacity (about 1000 pages) and therefore needs to reset the toner counter quite often. Resetting the counter for a good-printing cartridge also helps to use that cartridge’s toner life to the end.

A bit of theory. When a new cartridge is installed in the printer, the gear on it presses with its protrusion on the drive of the cartridge presence flag. After starting the engine of the device, this gear turns 1/2 turn and does not rotate anymore during the further operation of the printer. In the process of rotation, the gear 2 times removes the pressure from the drive of the cartridge presence flag. The machine interprets this fact as a signal to install a new cartridge and resets its internal counter of cartridge prints. If before this fact the “Toner” error was indicated, then it is reset and the indicator goes out. Electrically, the cartridge presence sensor is a transistor optocoupler. The emitter of the phototransistor is connected to the common wire, and the collector output through the pull-up resistor is connected to the power wire. The signal from the collector goes to the main board. When the optocoupler slit is open, the signal is close in level to zero potential; when the slit is closed, the signal is high. The idea of ​​the reset button is to connect a normally closed button in series with the phototransistor, by pressing which simulates the installation of a new cartridge. In this case, the button does not interfere with the normal normal operation of the sensor.

Required materials: 2 pieces of thin insulated wire 10 cm long and a normally closed (N.C.) panel mount button with nut:

READ  Laser printer smudges paper when printing

Tool: soldering iron, soldering supplies, stationery knife.

  • Remove the left side panel. To do this, pull out the paper tray, open the front and back covers. First remove the upper rear hook of the side panel, then slide the rear of the panel down a bit, then remove the front upper hook. Then the left panel is removed.
  • Lift up the top panel. It is enough to remove the side and front left hook:
  • We remove the indication and control board. It is fastened with two latches to the frame of the device. Disconnect the ribbon cable to be removed from the main board.
  • In the removed left side panel, make a hole to accommodate the button. The location of the hole can be seen in photos 3 and 4. Install the button and fasten it with a nut:
  • User manual text:

    Open the front cover. Press and hold the GREEN button for 4 seconds until all four lights come on. As soon as all indicators light up, release the GREEN button. Close the front cover.

    Open then close the front cover. 3 seconds after the start of the engine of the device (not to be confused with the fan!) 2 times press the BLACK button.

    Of course, this scheme also applies to other Brother printers and MFPs using this cartridge identification scheme.

    Soft toner reset

    Developers create additional maintenance functions for their equipment. Among them is a paint dumping tool. It runs only through the built-in display, so it is not suitable for all users. If you are that lucky owner of a device with a screen, follow these steps:

    • Turn on the all-in-one and wait for it to be ready to go. During the display of the inscription “Please wait” do not need to press anything.

    Next, open the side cover and click on the “Clean” button.

    On the screen you will see a question about replacing the drum, to start the process click on “Start”.

    Close the side cover if the corresponding message appears on the screen.

    Now you can go to the menu, move around it using the arrows to get acquainted with the state of the counter at the moment. If the operation was successful, its value will be equal to 100%.

    As you can see, zeroing paint through a software component is not difficult. However, not everyone has a built-in screen, and this method is not always effective. Therefore, we recommend that you pay attention to the second option.

    How to reset the toner counter for your Brother printer

    The instructions below will work best for most Brother printing machines as they are all similar in design and quite often include the TN-1075 cartridge. We’ll look at two ways. The first is suitable for users of MFPs and printers with a built-in screen, and the second is universal.

    Reset Toner Counter for Brother Printer

    Almost all Brother printers and MFPs are equipped with a built-in mechanism that keeps track of printed pages and blocks ink when it is supposed to run out. Sometimes users, after refilling a cartridge, encounter a problem in which the toner was not detected or a notification appears asking to replace it. In this case, you must reset the ink counter to continue printing. Today we will show you how to do it yourself.

    Manual reset

    The Brother cartridge has a reset sensor. It needs to be activated manually, then the update will be successful. To do this, you need to independently remove the components and perform the rest of the actions. The whole procedure looks like this:

    • Turn on the printer, but do not connect to the computer. Be sure to remove the paper if installed.
    • Open the top or side cover to access the cartridge. Do this action, taking into account the design features of your model.

    Remove the cartridge from the equipment by pulling it toward you.

    Disconnect the cartridge and drum unit. This process is intuitive, you just need to remove the latches.

    Insert the drum part back into the device as it was previously installed.

    The zero sensor will be located on the left side inside the printer. You need to put your hand through the paper feed tray and press this sensor with your finger.

    Hold it and close the lid. Expect the start of the work of the apparatus mechanisms. Then release the sensor for a second and press again. Hold until the engine stops.

  • It remains only to mount the cartridge back into the drum part and you can start printing.
  • If, after a two-way reset, you still receive a notification that no toner is detected or ink has run out, we recommend that you check the cartridge. Refuel if necessary. You can do this at home, using the instructions attached to the device, or contact the service center for help.

    We have covered two available methods to reset the toner counter on Brother printers and MFPs. It should be borne in mind that some models have a non-standard design and use cartridges of a different format. In this case, the best solution would be to use the services of service centers, since physical intervention in the components can provoke device malfunctions.