Pantum M6500 Printer Writes No Cartridge

MODS Grand Theft Auto V

The largest collection of mods for Grand Theft Auto V and GTA San Andreas

Pantum printer writes cartridge out

Modern inkjet cartridges equipped with a chip that controls ink consumption. If it is designed for four hundred pages, as soon as this limit is reached, the Pantum m6500 printer will display a message that ink has run out and the cartridge needs to be replaced. Any user may be faced with a situation where the fill chip needs to be zeroed, since toner consumption is counted by counting pages printed, not actual ink consumption. In fact, there is still enough ink in the device, but the printer displays a message that the cartridge needs to be replaced.

Until the moment of filling the chip and after the procedure, the operation of the cartridge will continue to be blocked, since Pantum m6500 “sees” it empty. It is for this reason that from time to time you can hear the question from users: “Why does a message appear after refilling a cartridge that it is empty?” The answer is simple, you need to zero the chip in order for the device to function normally.

How to zero?

If after refueling the Pantum m6500 printer writes that the cartridge has run out, reset the chip. This can be done in several ways:

  • The easiest option is to replace the faulty chip; this procedure is only available in laser devices. Inkjet printers have a built-in chip that cannot be removed and replaced;
  • No way to replace? There are special programs for zeroing. However, it is better to entrust this procedure to professionals. For people who do not have the necessary knowledge, universal programmers are suitable, which can be applied to any model;
  • Zeroing can be done without the need for software. Just turn off your Pantum m6500 printer, pull out the cartridge and turn on the device. Next, in the service menu, press the “OK” button, and hold it for a few seconds. Then perform the following chain of actions, in turn press “Resert Menu”. “Ok”. “Partial Resert”. “Ok”. After the performed manipulations, the Pantum m6500 printer will turn off. Run it again, select your language and country. Next, the device will offer detailed instructions for further actions. They need to be followed with 100% accuracy. After that, the ink level should be full and the machine will start working properly.

How to turn off ink control

This function is only available in Canon devices, other manufacturers have NOT equipped their devices with the ability to deactivate ink control.

When one of the cartridges runs out of ink, a warning message appears on the screen. You can stop printing (stop / reset) or continue (ok). Depending on which option you choose, the document will be printed or the operation will be canceled.

After another ink cartridge runs out of ink, an alert will appear again prompting you to replace it. If your printer has a built-in cartridge, hold down the Stop / Reset button for thirty seconds. This will deactivate the ink monitoring function.

This action will NOT affect the operation of the Pantum m6500 printer in any way, the print quality will NOT deteriorate. For devices with several ink tanks, this action is carried out separately for each.

You can “opt out” of automatic ink control directly on the computer. Through the control panel go to the “Printers” section, Click on the icon of the required device and select “Properties”. A window will appear, select the “Maintenance” category in it, then “Printer Status Information”. “Options”.

Uncheck the box next to the line “Display warning automatically”. System Disconnect, and you will have to check the remaining ink yourself, periodically looking under the cover of the Pantum m6500 printer. Be aware that printing too many pages with an empty cartridge may damage the print head.

Of course, replacing the cartridge is not the most difficult procedure, but the chance of damaging the chip or device is high, so it is better to entrust the chip zeroing to professionals.

Modern inkjet cartridges equipped with a chip that controls ink consumption. If it is designed for four hundred pages, as soon as this limit is reached, the Pantum m6500 printer will display a message that ink has run out and the cartridge needs to be replaced. Any user may be faced with a situation where the fill chip needs to be zeroed, since toner consumption is counted by counting pages printed, not actual ink consumption. In fact, there is still enough ink in the device, but the printer displays a message that the cartridge needs to be replaced.

Until the moment of filling the chip and after the procedure, the operation of the cartridge will continue to be blocked, since Pantum m6500 “sees” it empty. It is for this reason that from time to time you can hear the question from users: “Why does a message appear after refilling a cartridge that it is empty?” The answer is simple, you need to zero the chip in order for the device to function normally.

How to zero?

If after refueling the Pantum m6500 printer writes that the cartridge has run out, reset the chip. This can be done in several ways:

  • The easiest option is to replace the faulty chip; this procedure is only available in laser devices. Inkjet printers have a built-in chip that cannot be removed and replaced;
  • No way to replace? There are special programs for zeroing. However, it is better to entrust this procedure to professionals. For people who do not have the necessary knowledge, universal programmers are suitable, which can be applied to any model;
  • Zeroing can be done without the need for software. Just turn off your Pantum m6500 printer, pull out the cartridge and turn on the device. Next, in the service menu, press the “OK” button, and hold it for a few seconds. Then perform the following chain of actions, in turn press “Resert Menu”. “Ok”. “Partial Resert”. “Ok”. After the performed manipulations, the Pantum m6500 printer will turn off. Run it again, select your language and country. Next, the device will offer detailed instructions for further actions. They need to be followed with 100% accuracy. After that, the ink level should be full and the machine will start working properly.

How to turn off ink control

This function is only available in Canon devices, other manufacturers have NOT equipped their devices with the ability to deactivate ink control.

When one of the cartridges runs out of ink, a warning message appears on the screen. You can stop printing (stop / reset) or continue (ok). Depending on which option you choose, the document will be printed or the operation will be canceled.

After another ink cartridge runs out of ink, an alert will appear again prompting you to replace it. If your printer has a built-in cartridge, hold down the Stop / Reset button for thirty seconds. This will deactivate the ink monitoring function.

This action will NOT affect the operation of the Pantum m6500 printer in any way, the print quality will NOT deteriorate. For devices with several ink tanks, this action is carried out separately for each.

READ  How to scan a document with a Samsung printer

You can “opt out” of automatic ink control directly on the computer. Through the control panel go to the “Printers” section, Click on the icon of the required device and select “Properties”. A window will appear, select the “Maintenance” category in it, then “Printer Status Information”. “Options”.

Uncheck the box next to the line “Display warning automatically”. System Disconnect, and you will have to check the remaining ink yourself, periodically looking under the cover of the Pantum m6500 printer. Be aware that printing too many pages with an empty cartridge may damage the print head.

Of course, replacing the cartridge is not the most difficult procedure, but the chance of damaging the chip or device is high, so it is better to entrust the chip zeroing to professionals.

In this article, we Disclose all the features of zeroing the cartridge, talking about the stages of zeroing and the pitfalls of this process.

Today, most cartridges from various manufacturers are equipped with ink consumption control chips, in more detail about the purpose of the chips and their features. Therefore, any user of copiers sooner or later faces the need to zero the chip, since the toner usage by the chip is counted by the page counting method. Accordingly, if only a couple of lines were printed on the page, then the ink consumption was minimal. And it often happens that when a message appears about the need to replace the cartridge, there is still a sufficient amount of consumables in it. And after refueling, the chip will still block the operation of the cartridge, because the printer will see it as empty. In this case, zeroing of the chip will be required, which can be done in several ways:

  • In laser printers The easiest way is to replace the chip. On the market you can find a large number of “zeroed” chips for both specific printer models and universal ones. But you need to take into account that the chip is installed in inkjet cartridges in such a way that it cannot be replaced.
  • If you cannot replace the chip, then you can use the special chip reset programs on the HP cartridge. But they should only be used by people with special skills, especially for laser printers. For ordinary users, universal programmers are suitable. these are programs suitable for many cartridge models. But in our market there is a large number of fakes, first of all, this fact must be taken into account. Therefore, zeroing the chip without consequences can be performed by our service engineers. You just need to call: 8 (812) 677-00-40 or write your contact details in the feedback on the website
  • But you can also reset the chip without using any devices.
    pantum, m6500, printer, writes

    For this you need:

  • Turn off the printer
  • Remove the cartridge from the device;
  • Turn it back on.

Then, in the service menu of the printing device, press and hold the “OK” button for some time. After that, the menu item “Resets Menu” is selected and again it is necessary to press “OK”, and then the item “Partial Reset” and again “OK”.

After THESE manipulations, the printer should turn off. If this happens, you need to turn the device back on and select the country and language. Next, the printer will offer instructions for the next steps. It is necessary to complete all of them without fail, after which the ink level should be 100%. This will mean “zeroing” the chip. If the ink indicator has NOT changed, then you need to repeat the manipulations, but instead of the “Partial Reset” item, select “Semi Full” or “Semi Full Reset”.

The easiest way is to press and hold the Reset / Stop button for 10 seconds. If this helps, then you will have to monitor the ink level yourself in the future.

Also, I would like to draw your attention to the fact that even if you follow all the instructions above, there is a high probability of ruining the copier or the CHIP may simply burn out and the printer will refuse to see the cartridge. We will help you save time, money for possible repair of the device and nerves.

Call by phone: 7 (812) 677-00-40 and we will answer all your questions.

MODS Grand Theft Auto V

The largest collection of mods for Grand Theft Auto V and GTA San Andreas

Pantum printer does not see cartridge

It is NOT rare that the device does not recognize the cartridge after refilling, or a message appears on the screen about the lack of ink or a request to replace the cartridge. This can happen after purchasing a third-party cartridge. But there is no need to worry. this article will consider most of the causes of such malfunctions, as well as ways to eliminate them, which you can make yourself, and not resorting to the help of specialists.

Accounting for paint consumption

First, you need to figure out how ink is counted. For THESE purposes the cartridge has a special chip programmed with a certain number of pages, which acts as a counter. The amount of ink in the cartridge is designed for the same number of pages and as soon as the number of printed sheets approaches the specified number, you will receive low ink messages. However, there is a small nuance. the amount of ink is designed for sheets completely filled with text or images, but in practice it is quite often necessary to print half-blank pages. In this case, the alerts about the lack of ink may differ from the actual presence in the cartridge.

It is worth noting that the chips can have a software lock, which makes it impossible to use the cartridge after refueling. Customers using printers from Epson may face this, other popular manufacturers such as Canon or HP often DO NOT use blocking.

Possible problems after refueling and their solutions

Now let’s look at what to do if the device does not see the cartridge. Do some basic steps first and your problem can be resolved after each:

  • Turn off the printer and turn it on after 30-60 seconds, re-initialize the device.
  • When turning on the device Remove and reinsert the cartridge into a click.
  • It may be worth cleaning the contacts on the cartridge from paint or oxidation products. To do this, remove the cartridge and wipe them with an eraser or alcohol wipe. At the same time, you can clean and check the integrity of the contacts on the print head of the printer.

Contacts on the cartridge. Do not apply heavy pressure when cleaning them as they may move and NOT align with the printhead contacts.

Contacts on the print head of the printer. Arrows indicate damaged elements.

If you have Refillable cartridges (Refillable cartridges) and the printer still gives an error and says “replace the cartridge”, then you should reset the refueling counter using a button or by simply closing the contacts on each cartridge. CISS are reset with one button. For clarity of this process, we recommend watching the video for your specific printer model.

If there are problems with the original ink tank, but the device still does not see the refilled cartridge with the refillable cartridge or CISS, then the contacts on the print head may slightly not coincide with their position on the ink tank. Try to squeeze the ink tanks tighter with a spacer.

Pieces of paper folded several times are perfect as a spacer.

If after all THESE actions you have a “printer error, replace the cartridge”. most likely, the chip is damaged and you will have to change it or the entire ink tank.

Modern inkjet cartridges equipped with a chip that controls ink consumption. If it is designed for four hundred pages, as soon as this limit is reached, the Pantum m6500 printer will display a message that ink has run out and the cartridge needs to be replaced. Any user may be faced with a situation where the fill chip needs to be zeroed, since toner consumption is counted by counting pages printed, not actual ink consumption. In fact, there is still enough ink in the device, but the printer displays a message that the cartridge needs to be replaced.

Until the moment of filling the chip and after the procedure, the operation of the cartridge will continue to be blocked, since Pantum m6500 “sees” it empty. It is for this reason that from time to time you can hear the question from users: “Why does a message appear after refilling a cartridge that it is empty?” The answer is simple, you need to zero the chip in order for the device to function normally.

How to zero?

If after refueling the Pantum m6500 printer writes that the cartridge has run out, reset the chip. This can be done in several ways:

  • The easiest option is to replace the faulty chip; this procedure is only available in laser devices. Inkjet printers have a built-in chip that cannot be removed and replaced;
  • No way to replace? There are special programs for zeroing. However, it is better to entrust this procedure to professionals. For people who do not have the necessary knowledge, universal programmers are suitable, which can be applied to any model;
  • Zeroing can be done without the need for software. Just turn off your Pantum m6500 printer, pull out the cartridge and turn on the device. Next, in the service menu, press the “OK” button, and hold it for a few seconds. Then perform the following chain of actions, in turn press “Resert Menu”. “Ok”. “Partial Resert”. “Ok”. After the performed manipulations, the Pantum m6500 printer will turn off. Run it again, select your language and country. Next, the device will offer detailed instructions for further actions. They need to be followed with 100% accuracy. After that, the ink level should be full and the machine will start working properly.

How to turn off ink control

This function is only available in Canon devices, other manufacturers have NOT equipped their devices with the ability to deactivate ink control.

When one of the cartridges runs out of ink, a warning message appears on the screen. You can stop printing (stop / reset) or continue (ok). Depending on which option you choose, the document will be printed or the operation will be canceled.

After another ink cartridge runs out of ink, an alert will appear again prompting you to replace it. If your printer has a built-in cartridge, hold down the Stop / Reset button for thirty seconds. This will deactivate the ink monitoring function.

This action will NOT affect the operation of the Pantum m6500 printer in any way, the print quality will NOT deteriorate. For devices with several ink tanks, this action is carried out separately for each.

You can “opt out” of automatic ink control directly on the computer. Through the control panel go to the “Printers” section, Click on the icon of the required device and select “Properties”. A window will appear, select the “Maintenance” category in it, then “Printer Status Information”. “Options”.

Uncheck the box next to the line “Display warning automatically”. System Disconnect, and you will have to check the remaining ink yourself, periodically looking under the cover of the Pantum m6500 printer. Be aware that printing too many pages with an empty cartridge may damage the print head.

Of course, replacing the cartridge is not the most difficult procedure, but the chance of damaging the chip or device is high, so it is better to entrust the chip zeroing to professionals.

There can be several reasons why the laser device does not see the cartridge and does NOT recognize it. In the overwhelming majority of cases, it is all about the chip: it is dirty or does not reach the contacts in the print head. But sometimes the situation is explained by damage to the contacts in the device itself.

Why the device does not see a new cartridge

Often this situation occurs if you just purchased a compatible model from a third-party manufacturer. Although these cartridges are cheaper, their quality leaves much to be desired. They are NOT designed for a large number of gas stations and quickly deteriorate. Also, you cannot be sure that the cartridge has not been poorly remanufactured and is NOT sold under the guise of a new product. Packaging is not a guarantee of quality.

When the product is new and branded, for example, from Epson, Canon or HP, carefully read the instructions or consult an Official Tech. Support (in agreement with the manufacturer).

What you can do yourself:

Check if it is installed correctly. Original products are easy to insert. If everything is done correctly, there must be a characteristic click.

Make sure the yellow seal is removed from the cartridge.

See if the cover of the cartridge module is well closed, take the printer off-line.

Why does the device not see a refilled cartridge?

Many models have a chip. If there is little ink, the chip blocks the cartridge and this block is NOT removed when ink is replenished. If the printer shows deceptive data in the toner, for example, in fact it is, but the device shows that it is not there, and vice versa, then this may indicate just a blockage. But it can be removed and for this you need:

  • Reset the waste toner level via the computer.
  • Clean the cartridge and printer parts.

Did not help? Check the markings on the chip to match the printer model. Another reason is the protrusion of the plastic chip holder from the bottom. If this happens, cut off this part with a clerical knife, and then clean the chip with a regular eraser.

The device does not see the cartridge: what to do

This situation can be eliminated if:

  • Reboot. You need to turn off and turn on the device after 30-40 seconds.
  • Remove and insert cartridges. Turn on the device, open the cover. When the carriage moves to the cartridge replacement position, remove and reinsert.
  • Clean cartridge contacts, print head.
  • Reset the counter after refueling. If you are using a toner supply system, read the instructions. Each option performs a reset differently. However, before doing this, we will disassemble the cartridge and remove the microcircuit.
  • Align the chips. They often shift after cleaning.

ATTENTION. Some manipulations by non-professionals can permanently disable the device. In this case, you can NOT fix anything with your own hands, and you may need to repair the printer.

Pampers (absorber). Absorbs waste ink when printing or head cleaning. Located at the very bottom of the device. To remove it, you must almost completely disassemble the device. Therefore, we strongly do not recommend doing this without experience.

Cleaning contacts. This must be done very carefully, and not touching with your hands, otherwise there is a risk of damage to the plastic cable (it is on it that the contacts are located). If you need to clean the printer contacts, turn it off. An alcohol cloth is usually used for cleaning.

Still not detecting a refilled cartridge? If the device does not see the cartridge after refilling, even when it is original, the device may need to be replaced. There are also cases when only printer flashing is needed for comfortable and stable work. In THESE cases, it is worth entrusting the repair to specialists.

Urgent recovery of printers and refilling of cartridges

Almost all popular manufacturers of inkjet and laser printers Insist on purchasing new cartridges after using old ones. This is not suitable for everyone. The way out is to try to refuel yourself, risk damaging the printer, or use the services of a service center.

Reasons for contacting professionals:

  • The product does not recognize the cartridge and does not see paper, but there is paper in the tray.
  • You need to replace parts, flash the chip;
  • The computer does NOT recognize the machine;
  • The appearance of defects in printing, etc.

Unable to fix your printer problem yourself? Contact TonFix, a professional workshop for servicing, repairing printers and refilling cartridges. We have the necessary equipment and experience for over eight years. We will resolve any issue as soon as possible. The master will carry out an urgent visit to any address in Kiev. We work efficiently, quickly, with a guarantee.

Pantum m6500 printer writes cartridge comments

Modern inkjet cartridges equipped with a chip that controls ink consumption. If it is designed for four hundred pages, as soon as this limit is reached, the Pantum m6500 printer will display a message that ink has run out and the cartridge needs to be replaced. Any user may be faced with a situation where the fill chip needs to be zeroed, since toner consumption is counted by counting pages printed, not actual ink consumption. In fact, there is still enough ink in the device, but the printer displays a message that the cartridge needs to be replaced.

Until the moment of filling the chip and after the procedure, the operation of the cartridge will continue to be blocked, since Pantum m6500 “sees” it empty. It is for this reason that from time to time you can hear the question from users: “Why does a message appear after refilling a cartridge that it is empty?” The answer is simple, you need to zero the chip in order for the device to function normally.

How to zero?

If after refueling the Pantum m6500 printer writes that the cartridge has run out, reset the chip. This can be done in several ways:

  • The easiest option is to replace the faulty chip; this procedure is only available in laser devices. Inkjet printers have a built-in chip that cannot be removed and replaced;
  • No way to replace? There are special programs for zeroing. However, it is better to entrust this procedure to professionals. For people who do not have the necessary knowledge, universal programmers are suitable, which can be applied to any model;
  • Zeroing can be done without the need for software. Just turn off your Pantum m6500 printer, pull out the cartridge and turn on the device. Next, in the service menu, press the “OK” button, and hold it for a few seconds. Then perform the following chain of actions, in turn press “Resert Menu”. “Ok”. “Partial Resert”. “Ok”. After the performed manipulations, the Pantum m6500 printer will turn off. Run it again, select your language and country. Next, the device will offer detailed instructions for further actions. They need to be followed with 100% accuracy. After that, the ink level should be full and the machine will start working properly.

Pantum m6500 printer

How to turn off ink control

This function is only available in Canon devices, other manufacturers have NOT equipped their devices with the ability to deactivate ink control.

When one of the cartridges runs out of ink, a warning message appears on the screen. You can stop printing (stop / reset) or continue (ok). Depending on which option you choose, the document will be printed or the operation will be canceled.

Ink cartridge

After another ink cartridge runs out of ink, an alert will appear again prompting you to replace it. If your printer has a built-in cartridge, hold down the Stop / Reset button for thirty seconds. This will deactivate the ink monitoring function.

This action will NOT affect the operation of the Pantum m6500 printer in any way, the print quality will NOT deteriorate. For devices with several ink tanks, this action is carried out separately for each.

You can “opt out” of automatic ink control directly on the computer. Through the control panel go to the “Printers” section, Click on the icon of the required device and select “Properties”. A window will appear, select the “Maintenance” category in it, then “Printer Status Information”. “Options”.

Toner in the printer

Uncheck the box next to the line “Display warning automatically”. System Disconnect, and you will have to check the remaining ink yourself, periodically looking under the cover of the Pantum m6500 printer. Be aware that printing too many pages with an empty cartridge may damage the print head.

Of course, replacing the cartridge is not the most difficult procedure, but the chance of damaging the chip or device is high, so it is better to entrust the chip zeroing to professionals.