The printer prints only half of the sheet what to do

Cartridge: condition and amount of ink

The cartridge is the element of the printer that must be tested first for damage. Indeed, often the reason for incorrect printing (stripes or on the floor of the sheet) is the ink level, which tends to zero.

In order to check the level of the remaining ink, it is worth using the corresponding function in the printer itself or the computer. However, it is worth remembering that this function does not always correctly display the real amount of paint in the cartridge hopper. What to do in this case? Just in case, you should remove it from the printer and shake it gently, then put it back in place and check the ink level again. After you have done this manipulation 2-3 times. calculate the average from the obtained figures. This will be the real amount of paint. The less it is in the cartridge, the more likely it is that this is the cause of the breakdown.

printer, prints, only, half, sheet

If the amount of ink is almost zero, just refill the cartridge yourself or use the services of the service center. Unfortunately, in this situation, this is the only solution.

There are also situations when the cartridge is completely filled with ink, but the Canon printer stops and prints only half of the sheet. In this case, the reason may be incorrect refueling or poor-quality consumables, that is, paint. In this case, it is necessary to clean the cartridge and refill it, possibly with the help of a more qualified specialist.

Cartridge: wrong position

One of the possible causes of a cartridge malfunction is a situation completely independent of the amount of ink. Why does the printer print on half a sheet? It may have been installed incorrectly. In this case, open the printer and carefully inspect the position of the installed cartridge. If you notice even a slight skew on one side, remove the cartridge and correct it to a completely level position.

Important! Please note that after installation, the hole on the side cover must absolutely match the hole located near the photo cylinder.

How to fix if the printer prints half a sheet

A printer breakdown is always unpleasant, as the device no longer prints documents correctly. But do not rush to immediately carry your equipment to the service center. Why? If the Canon 2420 printer prints on half a sheet, then sometimes this problem can be solved without the intervention of a specialist. There are several common reasons for such a malfunction, which we will analyze.

Scanner ruler

What if the document comes to the printer not from a computer / laptop, but directly from a scanner? It is worth paying attention to his condition, and specifically to the normal condition of his line.

What to do in this situation?

  • Print your document.
  • If the printer prints half a sheet and stops, and then it is either completely white or completely black. mark the transition border.
  • Open the scanner lid and start the scanning process without using any documents.
  • Notice where the reading line stops.

If the printer does not print normally, but only to the border where the scanner line stopped, the fault is in it. To fix such a breakdown, the skills of an ordinary user to handle the printer will not be enough. In this case, it is better to contact the service center for help. Why? By trying to fix the course of the ruler yourself, you can create additional malfunctions, which will cost even more to fix.

Connection stability

If you are absolutely sure that the problem is not with the cartridge, then pay attention to the normal connection of the computer / laptop to the printing device, when it prints the document only on half of the sheet. Do not dismiss such a problem as a malfunction of the USB port, through which the connection between the device and the PC takes place. To correct this problem, remove the USB cable and try to connect it to a different port on the computer or laptop assembly. Select a tested and resilient port that you are confident in working.

If after all the manipulations, the Canon printer still stops and prints on half of the sheet, leaving the other half black or white, contact the service center. Perhaps the problem is more difficult to diagnose and only a qualified technician can detect it.

Epson printer prints blank sheets

Owners are faced with the fact that the printer prints white sheets. Epson is no exception and its devices suffer from the same disadvantages. Although Epson printers are the most durable and reliable of all inkjet printers, they still need preventive maintenance and repair.

An indirect cause of the malfunction was the use of CISS and refillable cartridges. The price of branded new cartridges is half the cost of a new printer, so the owners have long acquired CISS and PZK, which allow them to make a printing press out of an ordinary printer.

The reasons why the Epson L800 printer prints blank sheets:

  • dry ink in the print head;
  • the inkwells were airing;
  • fuse F2 on the main board blown.

If the printer prints blank sheets, Epson XP-103:

  • Closed air holes in refillable cartridges are a common problem;
  • the problem occurs due to the downtime of the printer. channels in the print head dry up or clogged.

The printer prints blank sheets of Epson CX4300:

  • this can happen after resetting the diaper and zeroing the ink tanks;
  • if the air ducts are closed.
READ  Built-in Memory Size of Laser Printer

The printer prints blank sheets of Epson L355:

  • the ventilation holes are closed;
  • the transport blocker is closed;
  • paint does not enter the plumes, they do not fill at all.

Epson L210 printer prints blank sheets:

  • fuse blown;
  • airing;
  • dried ink or nozzles.
  • dried ink in cartridges;
  • an airlock appeared;
  • blown fuse.

The printer prints blank sheets of Epson SX130:

  • failure occurs when discarding the diaper and cartridges;
  • no cartridge ventilation;
  • dried up GHG.

Drying or clogging of the print head is the main one of the listed options. This happens from prolonged downtime of the printer and the use of low-quality ink. This is treated by soaking the head or cartridge in an ultrasonic bath using a special flushing liquid.

If you cleaned or flushed the printer head yourself, a blown fuse on the main board is added to the inoperative head. As soon as a small amount of moisture gets inside, this immediately creates a short circuit and fuse F2 flies out. It is small enough and located at the very depth of the printer, therefore, a complete disassembly of the printer is required.

Airing often occurs during transportation or improper refueling. To eliminate it, it is necessary to pump out air from the cartridges, while the air valve must in no case be damaged, otherwise the cartridges will be permanently damaged.

In order to save your precious time and not to break your permanently expensive printer, contact a certified service center. You have the opportunity to call a specialist of the “Master-Service” center to your place. He will instantly identify any malfunction. This will save you the trouble of taking the printer to the workshop, because experienced employees can solve your problem without taking the printer.

Connection

The printing process involves performing certain actions to exchange information between the device and the computer. As an intermediary, in 99 percent of cases, a USB cable is used. Through a bad connection or damage to it, the connection is disrupted. Check the cable itself:

  • Disconnect the power.
  • Disconnect USB cable from PC and printer.
  • Connect the cord to the printer.
  • Insert the cable into one of the ports on the back of the computer.
  • Turn on the printer.
  • Try to print.

It is best to try using a different, finely working wire.

If the device is connected via Wi-Hi, then checking the signal quality is the first step. As an option to exclude the fault of problems with Wi-Fi, you can try printing with a USB connection.

Cartridge: wrong position

One of the possible causes of a cartridge malfunction is a situation completely independent of the amount of ink. Why does the printer print on half a sheet? It may have been installed incorrectly. In this case, open the printer and carefully inspect the position of the installed cartridge. If you notice even a slight skew on one side, remove the cartridge and correct it to a completely level position.

Important! Please note that after installation, the hole on the side cover must absolutely match the hole located near the photo cylinder.

Incorrect print settings

Most often, the printer only prints half a page due to incorrect settings in the software being used. Let’s consider how to fix the problem using the example of printing settings in a Word document.

  • Open a document with MS Word.
  • In the menu, go to the “Page Layout” tab.
  • Click on the item “Fields”.
  • At the bottom of the drop-down menu, select “Custom fields”.
  • In the “Fields” tab in the “Pages” block, next to the “multiple pages” line, select “Normal”.

In new versions of the office suite, the setting of the fields is in the “Layout” tab.

Scanner ruler

What if the document comes to the printer not from a computer / laptop, but directly from a scanner? It is worth paying attention to his condition, and specifically to the normal condition of his line.

What to do in this situation?

  • Print your document.
  • If the printer prints half a sheet and stops, and then it is either completely white or completely black. mark the transition border.
  • Open the scanner lid and start the scanning process without using any documents.
  • Notice where the reading line stops.

If the printer does not print normally, but only to the border where the scanner line stopped, the fault is in it. To fix such a breakdown, the skills of an ordinary user to handle the printer will not be enough. In this case, it is better to contact the service center for help. Why? By trying to fix the course of the ruler yourself, you can create additional malfunctions, which will cost even more to fix.

Incomplete printing when photocopying

It is necessary to check the health of the scanner located under the glass of the machine.

  • Lift the lid of the MFP.
  • If there is paper on the glass, remove it.
  • Press the copy button.
  • Monitor the scanner’s performance.
  • He must walk at a steady speed. Mark the area where the scanner stops for more than one second or stops working completely.

Normally, the scanner will only stop at the end of the glass surface.

If you stop early, there is a chance of breakage. Only a specialist of the service center can repair.

Print settings

A commonplace cause of the problem may be an accidental incorrect print setting in the program that is being manipulated. In most cases, this is Word. Using his example, consider the procedure for elimination. We do this:

  • Opening a document in Word.
  • Find the “Page Layout” tab.
  • Select the item “Fields”.
  • At the bottom, click on “Custom Fields”.
  • We check the installed settings. “Normal” should be selected.
READ  Unable to Start Printer Check Printer Configuration

Reasons and solution

There are different types of faults, which are divided into two main groups: mechanical damage to the components of the system and a failure in the software settings. The first category includes the following problems:

  • Damage to the printer body and main control panel. As a result, the equipment cannot perform full-fledged work.
  • Chafing wires used to connect to power supply and computer.
  • Poor condition of the sensors on the cartridge case or breakage of special chips required for computer recognition.
  • Incorrect installation of elements in the corresponding compartment.
  • Accumulation of dirt, dried paint and debris inside the device.

Usually, this type of problem is easy enough to fix on your own without resorting to the help of a wizard. In case of failures in the program, make an independent diagnosis and the solution is not always possible. Perhaps the reasons for the termination of work were the following problems:

  • Incorrect connection and installation of software with a set of drivers.
  • Using outdated drivers.
  • Incorrect settings for the operation of the printer, it may be set to offline mode or a ban on printing.
  • Viral damage to the system that caused a failure in basic functions.

In this case, you need to contact a specialized service center, where you will quickly be assisted in diagnosing and eliminating the problems that have arisen.

Important! Do not make your own repair or replacement of equipment components in order to retain the right to free diagnostics and elimination of errors under warranty.

The printer began to print only half of the page. We are looking for a solution to the problem

If the printer or mfp prints half a sheet, then do not rush to go to the service center, because any user who is familiar with the device and the settings of his office equipment can cope with this problem. In this situation, there are several obvious reasons, which you can familiarize yourself with from the current article.

So, if your printer prints half a page, then the first thing that comes under suspicion, as in many other situations, is the device cartridge. Perhaps his bunker is almost empty. In order to make sure of this, you need to use a special function that is in the software of any modern printer. Thanks to it, you can find out the approximate level of ink or toner without removing the cartridge from the device. But keep in mind that it is not always worth relying on this option completely, it often “cheats” and shows the wrong amount of the remaining dye. It is best to open your inkjet or laser printer and pull out the ink / toner hopper, then shake it lightly and reinsert it. If after that the printer was able to print a full-fledged test sheet, then it means that the reason lies in the running out of the dye of the printer. It can be eliminated by replacing the consumable or refilling it.

If the printer does not print and the cause of this malfunction is not related to its cartridge, then it is possible that the connection between the device and the personal computer is of poor quality. Therefore, you should unplug the USB cable and connect it to each port on the PC in turn. Choose the fastest and most powerful port for a truly stable and reliable connection between the two devices. It would also be a good idea to inspect the cord. you may notice some external damage. Replace it with a new one if necessary.

Please note that you should not establish communication between the printing device and the computer using a USB extension cable or by connecting to the front port of the system unit.!

If the problem is still not resolved and the machine still does not print documents to the end of the page, but only to the middle, then try cleaning its consumables. It is possible that after refilling it, it is clogged. The fact is that as the cartridge works, it gradually accumulates a large amount of dyes, which, in turn, can negatively affect the print quality.

If the machine only prints one half of the document when copied, the scanner may be the source of the problem. But this raises the question: why is this happening? The fact is that the device receives only part of the page due to the fact that its scanner has stopped. You need to check this component of the printer without a document inside and with an open lid. At the same time, click on the button responsible for starting the scan, after which you can see how far the scanning ruler reaches. If you notice that it stops in the middle of the document, then the problem is definitely with the scanner. To fix this problem, you need to have advanced technical knowledge of office equipment scanners, otherwise contact any reliable repair center for printers, multifunctional devices, copiers and other similar devices for help.

In addition, if the printer does not print full page, the malfunction may be caused by improper assembly of the consumables for this device. Those. it could be assembled with a slight and almost imperceptible bias. In this case, the gap between the magnetic shaft and the drum on one side becomes slightly larger than on the other. To eliminate the problem, remove the pin on the right side of the cartridge and make sure that the hole that is located in the side cover of this part during assembly completely coincides with the hole in the part where the photo cylinder is located. Only then can you put the pin back in place.

READ  HP Laserjet Printer Cannot Connect

In addition, a page may only be printed halfway due to an unexpected error occurring during operation. In this case, the device will automatically stop its work until the malfunction found by it is eliminated.

Low toner or ink

Few printing devices inform the user in advance when the ink is low. In inkjet printers, the dye level can be determined using software, but when the device prints a document on half a sheet, it is safer to check manually.

  • Unplug the printer to avoid electric shock.
  • Open the cover on the front of the case.
  • Remove the ink cartridge or cans (for inkjet).
  • Check for dye. If it is less than half, it is better to refuel (read about refilling an inkjet cartridge).

You can try to reanimate the ink powder cartridge with a shake, but this will not be enough for a short time, and soon half-sheet printing will start again.

There may be a light on the front of the printer to indicate low toner.

The problem is in the drivers

Drivers can be damaged by accident by the user, by virus programs, or as a result of unsuccessful automatic updates. The only solution to the problem is reinstallation. It is easier and more reliable to use the drivers from the installation disc. If there is no disk, the latest software version is downloaded from the printer manufacturer’s website or an update is made via Windows Update. It is better to remove drivers from Windows first. For more information about all removal methods, see the link htpps: //poprinteram.ru/udalenie.html.

You can also get the update through the device manager by selecting the printer and through the context menu by clicking on “Update driver”.

Printer Eco-Mode

Some models include a save mode when the toner is running out. In the preview, the user sees that the portrait page will be printed completely on the entire A4 sheet, and as a result, a reduced image in landscape orientation is obtained on paper.

You can find out about the availability of the economy mode from the instructions for the device, it is also written there about setting up the printer for full printing. There may be a corresponding indicator or button on the body of the device.

You can also enable or disable toner saving in the print settings.

In the window that opens, the setting may have different names, depending on the operating system.

Dirty cartridge

If the printer begins to print an incomplete page, but there is enough ink in the cartridge, the reason may be dirty. Paint could get caught in the nozzles. The head is cleaned with rubber gloves. The table is pre-covered with old newspapers or unnecessary paper. A special liquid for rinsing the head, cotton swabs or tampons is prepared in advance.

Outwardly, the clogging is not visible, so it is better to clean the ink tank from time to time for the purpose of prevention.

  • Removing the cartridge from the printer.
  • Turn it over with the print head up.
  • You drip a cleaning agent onto the surface of the head.
  • Wipe the surface with a sponge or cotton swab.
  • Repeat the procedure until complete cleaning.

Incorrect print settings

Most often, the printer only prints half a page due to incorrect settings in the software being used. Let’s consider how to fix the problem using the example of printing settings in a Word document.

In new versions of the office suite, the setting of the fields is in the “Layout” tab.

| Message Posted on March 26, 2006 00:57 Episode

    • Offline
    • Info
    • Posts: 15 914
    • Registration: 20 Dec 05
    • Reputation: 116
    • Reputation 2019:
  • Pro
  • | Message Posted on March 19, 2006. 21:08 Scrubber

      • Offline
      • Info
      • Posts: 70
      • Registration: 25 Dec 05
      • Reputation: 0
    • Own
    • | Message Sent on March 19, 2006 00:03 Scrubber

        • Offline
        • Info
        • Posts: 70
        • Registration: 25 Dec 05
        • Reputation: 0
      • Own
      • CISS Forum: Printing stops at half CISS Forum

        | Message Posted on March 18, 2006 15:30 Scrubber

          • Offline
          • Info
          • Posts: 70
          • Registration: 25 Dec 05
          • Reputation: 0
        • Own
        • | Message Sent on March 19, 2006. 10:15 AM Yuri

            • Offline
            • Info
            • Posts: 687
            • Registration: 01 Jul 04
            • Reputation: 13
          • Specialist
          • | Message Sent on March 25, 2006 22:14

            Unidentified_AlexK-Unregistered (Mar 24 2006, 04:24 PM) wrote:

            | Message Posted on March 18, 2006 23:45 Episode

              • Offline
              • Info
              • Posts: 15 914
              • Registration: 20 Dec 05
              • Reputation: 116
              • Reputation 2019:
            • Pro