What does it mean there is no toner in the printer?

If the printer writes no toner what to do

does, mean, there, toner, printer

Often, many users of printing devices are faced with the need to solve the following problem: there is no toner in the printer, what is it. The fact is that after refueling, in some cases, the message “low toner”, “replace toner” or “need to replace the toner cartridge” is displayed on the screen of the printer or computer. In some cases, the device may ask the user for the following action: insert the toner card. Such inscriptions appear in the event that the copy sensor of the device is blocked or the cartridge is in a faulty condition. But the first one is the most common reason. To solve it, you will need to reset the counter.

Non-original cartridge

Leading manufacturers of printers and multifunctional devices, in pursuit of profit, do not allow the installation of cartridges of the same type produced by other firms on their equipment. The process is controlled by special chips. Non-original parts are much cheaper, but during installation they may not work. The printer in such cases writes “no toner” or “replace the cartridge”.

The problem is solved by flashing the printer, after which the device does not recognize the chips. A similar operation with the cartridge chip does not completely remove the problem, but postpones it until the next part replacement.

Important: in Samsung printers, the manufacturer often puts a fuse instead of a chip. In this case, it must be burned. It is enough to install a weak fuse, for example, 0.0625A, in the slot located on the front of the cartridge. Turning on the printer for the first time burns it up, the problem is fixed.

It is very difficult to reprogram the printer yourself. Better to trust the masters of specialized workshops.

about the problem

So, if your printing device says “replace toner”, then you can solve this problem using two different methods, each of which is proven and quite effective: software and hardware. On some cartridges, for example, Brother, in order to minimize the risk of such an error after refilling the cartridge, it is necessary to carefully seal the window on its side cover using opaque tape. The fact is that after the toner starts running out, the light penetrating through this window activates the sensor, which displays the message “low toner” or the remaining amount of the dye (toner remaining) on ​​the display of the device or PC monitor. Then the copy counting sensor comes into play, which, after printing about two hundred copies, automatically blocks the operation of the printer or MFP. After that, the error “add toner” will appear, although the toner in the cartridge capacity may be enough to print several dozen, and maybe even hundreds of sheets.

Toner Empty

The end of the toner in a cartridge can be seen:

  • deterioration in print quality;
  • printer signals.

In the first case, printing can be extended by several dozen copies using a few simple manipulations: remove the cartridge, gently shake it 5-6 times, and then gently shake it from side to side in the longitudinal direction. In this simple way, toner residues will be evenly distributed inside the container.

If the printer stops printing, check the number of copies printed. If it is close to the established indicator, the cartridge will have to be refilled or replaced.

Attention: most printers are void of warranty when refueling a cartridge. replacement only. The possibility of refueling is indicated in the operating instructions.

For reference: a printer manufacturer sells its products with a 50% cartridge refill. Therefore, you should not look for other reasons for stopping printing if the work of a new device is terminated in the region of 45-55% of copies of the declared number.

Copy counter problems

Cartridge replaced, but no toner is displayed. What does it mean there is no toner in this case? This message appears if the number of printed copies has not been reset from the previous cartridge.

  • changing printer settings (software method);
  • hardware.

The hardware method is simple and effective, but not suitable for all cartridges. It is used only if there is a window on its side cover, with the help of which the reader is started.

The principle of operation is as follows: reducing the toner in the container opens the window, the light through it falls on the photocell of the counter, the latter starts and, having counted about 200 copies, stops the printing process. The inscription “no toner” appears, although in reality there is enough powder for several dozen or even hundreds of copies. Resolves the issue by covering the window with opaque tape.

In all other cases, the copy counter can be changed by setting other printer settings.

Each printer has a different sequence of operations. Let’s show the principle of such a reset using the example of a Ricoh printing machine.

  • Press the button “User parameters”.
  • The next button is “OK”.
  • After the message “Reset toner counter” appears on the display, press “OK” again.
  • Up and down arrows. “Left”, “right” we find in the settings menu the item “Enable”.
  • By pressing “OK” we reset the counter.

If everything is done correctly, the message “out of toner” will disappear and the printer will start working.

Cartridge installed incorrectly

The problem could be dirty contacts that prevent the printer from seeing toner. The repair is simple. Remove the cartridge and wipe the contacts with a cotton swab.

Hardware method

If your printer says that there is little toner left in it, or it even reports that it is time to change the toner cartridge (replace toner), then you can try to solve this problem using the hardware method. This method is suitable for many Brother machines. It means direct intervention in the mechanics of the printing device, and therefore not every user of office equipment can use it.

First of all, before proceeding directly to work to eliminate the above problem, you must turn on the printer or MFP and wait until the noise coming from the device becomes noticeably quieter. Then, carefully detach the lever on the left side of the printer and slide it into the cabinet. Then, slowly pull out the cartridge by grasping the handle specially designed for this action. Divide the removed part into its component parts, namely, the drum unit and the toner cartridge. To solve this problem, click on the mount on the side. Then insert the drum unit into your printer.

Clamp the opening sensor using a screwdriver to simulate the presence of the lid when closed. You will also have to simulate the presence of a cartridge by holding down the checkbox for this purpose. As soon as you notice that the gears began to spin, release the checkbox, and then press again. Within 4 seconds, you should perform this procedure twice. Without practice, you are unlikely to be able to solve this problem the first time. In this case, it is important that after the second click on the flag, it remains in the clamped position.

Wait until the device dies down to release the sensor, simulating a closed panel, which you have been holding all this time with a screwdriver. Next, connect the lever to the front cover and reinstall the assembled consumables. Close the lid and test the work done.

Also, the hardware method means the physical replacement of the cartridge chip; this procedure is usually carried out when refueling a laser cartridge. You can find out more about it by reading the section of instructions for refueling.

Canceling Duplex Printing: Methods

If your printer is configured for duplex printing, you can add a blank after each sheet to your document using the page break tool to print the document correctly on one side. But this is a time-consuming method, with the use of which the user’s extra time was spent on preparing the document, on the second run, which takes a few seconds. Higher energy costs, higher risk of paper jams.

READ  How to cancel a specified print on the printer

It is easier and more correct to use one of several correct ways to cancel a duplex:

  • The first option is designed for PCs running Windows:
  • using the key or icon with a flag go to the “Control Panel” menu;
  • select the “Devices and Printers” submenu;
  • find your device by specifying its make and model;
  • right-click on its icon;
  • in the drop-down menu, find the line “Double-sided printing” and uncheck the box next to it;
  • confirm your choice by clicking “OK”.

From now on, printing will be one-sided. You can return the duplex by performing the same set of actions and returning the check mark to the option “Two-sided printing”.

In addition to the OS settings, you can change the settings of the printer itself:

  • follow the first 5 points of the previous instructions;
  • go to the submenu “Printer Properties”
  • select the “Profile” tab, in it. “Default settings”;
  • in the view settings, change the print style by unchecking the box next to the double-sided option;
  • print a test print with the new specifications or print the entire document.

If you need to save just such settings for further use of the printing device, then do the following:

  • go to the printer settings;
  • select the item “Preliminary settings”;
  • you need to select the “Save current settings as preliminary” option. To speed up the setup process next time, save this set of options under any name you can understand.

How to cancel duplex printing depending on Windows

Cancellation of duplex printing is the same in any version of Windows, from XP to 10. In XP, the name of the very first menu is different. not “Devices and Printers”, but “Printers and Faxes”. Such nuances can be found in various versions of Windows, but it will not be difficult to intuitively understand where exactly to look for the settings you need.

How to cancel duplex printing on a printer

When you need to print documents in which an image or text is located on both sides of a sheet of paper, double-sided printing (aka duplex) saves a lot of effort and nerves. There is no need to turn the sheets over, watch the top and bottom of the sheets, make a test print, so that later you do not have to reprint the entire work. The computer and the printer will do everything themselves, the operator’s concern is to send the file for printing and make sure that there is enough paper. But what if the printer is configured for duplex, and you need to print a document in which only one side is required?

What to do if printing on both sides is not canceled

You have met all the conditions, but if you restart your computer (or turn it off and on), the product still prints on both sides? This is rare, but it happens. This means that something happened with the settings of the printing device itself, and you need to return them to the factory settings, or the driver is to blame.

  • remove the printer from the list of devices (the first 5 points of the instructions, then by right-clicking, select “Remove device” and confirm the choice);
  • if you have installed programs to manage the printer on your computer, uninstall them (Control Panel / Add or Remove Programs).
  • go to the manufacturer’s official website and find on it a driver for a specific model suitable for a specific system (there may be differences not only between Windows versions, but also between 32- and 64-bit systems);
  • install the downloaded driver and software, if necessary for your model.

To reset the settings of the printing device, there are two ways: software and hardware. Hardware should be looked for in the instructions for a specific printer model, if it has been preserved. Most often, there is no paper instruction for a long time, but it can be found on the manufacturer’s website. To do this, you need to know exactly the model of the device. It is indicated on the printer itself, and in addition, you can find this data in the “Devices and Printers” tab.

The software method involves the use of software that was installed on a computer. Programs differ depending on manufacturers and models, and it is best to find the item “Restore factory defaults” in the software help.

After resetting the settings, you will need to check if everything is set as you need. But duplex is not included in the list of default settings by any manufacturer of printing devices.

Why isn’t he

There can be only two options: you have run out of “paint” and it’s time to buy a new cartridge, or there are some malfunctions in the printer that need to be eliminated immediately.

IMPORTANT! Pay attention to how the printer informs you about the lack of toner. when the ink starts to run out, a special sensor comes into action, which shows you a notification. After that, the printer counts 200 copies, after printing which the operation of the device is automatically blocked, even if there is still enough ink for several pages of printed text or photographs.

There is no toner in the printer, what does it mean

An increasing number of computer users purchase printers for themselves. these devices are very useful at the present time, when there is a need to constantly print a large amount of very different information. documents, abstracts or just any files that will not be so convenient to view from a PC screen.

But sometimes you have to face some difficulties in the operation of the device. What to do if an incomprehensible “no toner” notification suddenly appears on the computer and can a beginner deal with the problem? You will learn about all this in this article.

What does “no toner in printer” mean?

Not everyone is familiar with the definition of the word “toner”, so the user may simply not understand what exactly is missing for the correct operation of the printing device. In most cases, such a notification appears within a fairly short time after the last refill of the cartridge.

There can be several reasons for the problem at once. But first you need to figure out what toner is.

What is toner

Toner is a special powder that is used to apply to paper. Users can also refer to it as simply paint.

Such a powder is made specifically for printers and is produced only in four colors: black, red, blue and yellow. Other shades are achieved by mixing these colors. in this way, you can achieve almost any color combination, which makes modern color printers an indispensable thing in everyday life.

Toners are inserted into laser printers as cartridges are familiar to everyone. Now let’s take a closer look at what the “no toner” message that appears on the screen means and what it is spent on.

What to do

To exclude the possibility of breakdown, you can try to restore the work using the program method. This does not require special skills or deep knowledge in the field of technology, so any ordinary user can cope with the task.

First of all, turn on the printer and wait until all the necessary preparatory operations are completed. this can be determined using the volume level of the noise produced by the device. Then open the lid and press the Stop button, followed by Start and Up. Then hold down the “Down” button until the display shows zeros.

After that, do not forget to click “OK” and close the printer cover.

Another option is to flash the printer, which only needs to be done once, but this method is a little more complicated than the one described above. advanced users can also try to restore the printer using the hardware method. in this case, you will have to disassemble the device. If you are not sure that you can handle it and can return everything to its place, it is better not to do this.

Now you know what toner is and why the printer may suddenly start showing the “Out of toner” notification. In order to solve this problem, you just need to make a few simple manipulations, after which the printing device will start working again in the usual mode.

How to clear the toner change message for Brother printers and MFPs?

Non-native cartridge

Some manufacturers do not allow other brands to be installed on the printer. In this case, the cheap analogue will be recognized by a special chip integrated into the equipment. The printer will not work, and the user will see a message about the need to change the toner. You can solve the problem by flashing the device, after which it will finish distinguishing between cartridges.

READ  Printer Paper Jammed What to Do

For all Brother laser printers and MFPs

This article is for self-resetting the message about the need to replace the toner. The message might look like: Replace toner cartridge, Replace toner, Toner low, Replace toner cartridge.

Perhaps you have a Brother starter cartridge, which does not have a mechanism for resetting the cartridge counter, or after refilling, the mechanism did not work. Also, the article can be useful in that you can reset the message about the need to replace the toner cartridge, thereby printing the remaining toner in the cartridge to the end.

Since there are several types of Brother cartridges, like the machines themselves, the ejection mechanism is different.

Copy counter malfunction

This message occurs when the number of prints made by the previous cartridge has not been cleared.

It is not difficult to eliminate the problem, if the side cover of the device for printing is equipped with a window for reading copies. The window is sealed with opaque tape. Now the light on the photocell that counts the number of printed sheets does not hit and the printing will be stopped only when the dye powder is fully used.

If there is no such window, you can reset the counter by changing the options of the printer itself:

  • Click on the button “User parameters”.
  • Click OK.
  • We are waiting for the message “Reset toner counter” to appear on the monitor, click OK.
  • In the options menu, we are looking for, using the arrows, the “Enable” item, click OK.
  • Counter reset to zero.

Important! It is necessary to carry out work after a complete stop of the MFP.

Incorrect cartridge installation

The device may not “see” the toner if the cartridge is not supplied properly or the contacts are dirty.

In this case, you just need to remove the element, wipe the contacts with a cotton pad and insert the part back.

Non-original cartridge

In order for users to buy consumables of the printing device manufacturer, a chip is installed on it, which does not allow the use of products of other companies. “Native” consumable is not cheap and choosing the cheapest, but good-quality model, you can save working capital. The problem is solved by flashing the printing device, after which the message about the lack of toner when installing a non-unique cartridge will not come.

Important! It is better to entrust the task of unlocking the chip to a professional.

How to clear the toner and drum change message for color 9020/3140/3170/9330

If an error appears with the Brother 9020 printer, open the top cover, press and hold for about 2-3 seconds. In the list that opens, we make a choice of a cartridge or an imaging drum of a suitable color for you.

For the Brother 3140 printer, to eliminate these errors, it will be correct to open the top cover of the turned on printer and press the “Secure” and “Сancel” buttons at the same time. Having selected the color cartridge or imaging drum you need to reset, press “OK” and “Up”.

The correct procedure for resolving toner and imaging drum errors for the Brother 3170 Color Printer is to open the top cover and press the Secure and Cancel buttons on the printer at the same time. In the reset menu that appears on the monitor of the printing device, we select the cartridge of the color you need or the drum unit. Then press the “OK” and “Up” keys.

To eliminate the errors that have appeared related to replacing the toner or drum unit of the functional color printing machine Brother 9330. You need to do the following: Open the top cover, press and hold for about 2-3 seconds. Select a drum unit or a cartridge of the appropriate color from the menu list.

Non-original cartridge

Leading manufacturers of printers and multifunctional devices, in pursuit of profit, do not allow the installation of cartridges of the same type produced by other firms on their equipment. The process is controlled by special chips. Non-original parts are much cheaper, but during installation they may not work. The printer in such cases writes “no toner” or “replace the cartridge”.

The problem is solved by flashing the printer, after which the device does not recognize the chips. A similar operation with the cartridge chip does not completely remove the problem, but postpones it until the next part replacement.

Important: in Samsung printers, the manufacturer often puts a fuse instead of a chip. In this case, it must be burned. It is enough to install a weak fuse, for example, 0.0625A, in the slot located on the front of the cartridge. Turning on the printer for the first time burns it up, the problem is fixed.

It is very difficult to reprogram the printer yourself. Better to trust the masters of specialized workshops.

Why the printer writes, there is no toner and what to do

Users of printing machines in the process of work are faced with the inscription on the computer monitor or printer screen: “no toner”, “replace toner” and similar, depending on the model of the device.

For reference: toner is a low-melting dispersed powder made of polymer materials, graphite and resin. Used in laser printer cartridges.

The appearance of the inscription can be caused by 5 reasons:

  • there is really no toner;
  • cartridge installed incorrectly;
  • counterfeit cartridge:
  • the device that reads the number of copies is blocked;
  • the toner container is defective.

Cartridge installed incorrectly

The problem could be dirty contacts that prevent the printer from seeing toner. The repair is simple. Remove the cartridge and wipe the contacts with a cotton swab.

Copy counter problems

Cartridge replaced, but no toner is displayed. What does it mean there is no toner in this case? This message appears if the number of printed copies has not been reset from the previous cartridge.

  • changing printer settings (software method);
  • hardware.

The hardware method is simple and effective, but not suitable for all cartridges. It is used only if there is a window on its side cover, with the help of which the reader is started.

The principle of operation is as follows: reducing the toner in the container opens the window, the light through it falls on the photocell of the counter, the latter starts and, having counted about 200 copies, stops the printing process. The inscription “no toner” appears, although in reality there is enough powder for several dozen or even hundreds of copies. Resolves the issue by covering the window with opaque tape.

In all other cases, the copy counter can be changed by setting other printer settings.

Each printer has a different sequence of operations. Let’s show the principle of such a reset using the example of a Ricoh printing machine.

  • Press the button “User parameters”.
  • The next button is “OK”.
  • After the message “Reset toner counter” appears on the display, press “OK” again.
  • Up and down arrows. “Left”, “right” we find in the settings menu the item “Enable”.
  • By pressing “OK” we reset the counter.

If everything is done correctly, the message “out of toner” will disappear and the printer will start working.

Toner Empty

The end of the toner in a cartridge can be seen:

  • deterioration in print quality;
  • printer signals.

In the first case, printing can be extended by several dozen copies using a few simple manipulations: remove the cartridge, gently shake it 5-6 times, and then gently shake it from side to side in the longitudinal direction. In this simple way, toner residues will be evenly distributed inside the container.

If the printer stops printing, check the number of copies printed. If it is close to the established indicator, the cartridge will have to be refilled or replaced.

Attention: most printers are void of warranty when refueling a cartridge. replacement only. The possibility of refueling is indicated in the operating instructions.

For reference: a printer manufacturer sells its products with a 50% cartridge refill. Therefore, you should not look for other reasons for stopping printing if the work of a new device is terminated in the region of 45-55% of copies of the declared number.

Toner container defects

If the container is damaged, it must be replaced. This problem does not occur often. The reason is careless handling of the cartridge.

The inscription “out of toner” may appear in case of other breakdowns, which are difficult to fix by yourself. In such cases, the repair must be carried out by a specialist.

What does it mean there is no toner in the printer?

The printer helps the computer user to display the results of their work (texts, graphics, photos) on solid media. The latter are paper or plastic film. Despite the growing popularity of electronic document management, the need for printing information is still great. Abstracts, term papers, texts of speeches, other files are easier to view and correct on paper.

In order for the information received to be clear and vivid, the peripheral printing device must work flawlessly. It is necessary to regularly carry out preventive examinations and change cartridges.

READ  Self-adhesive barcode printer

But even with proper care, the device malfunctions. In this publication, we will look at the causes and rules of behavior when the message “Out of toner in printer” appears. It indicates a problem with the printing device.

Non-original cartridge

Important! It is better to entrust the task of unlocking the chip to a professional.

Container incorrectly installed

With such a problem, the message appears immediately after installing a new cartridge. It must be removed, the grooves should be wiped with a cotton swab dipped in alcohol and reinstalled until it clicks. Then close the printer cover and continue working.

What does “no toner in printer” mean?

This message stops the printing process and confuses the user. Such an inscription is especially surprising and makes you worry if very little time has passed since the last refueling of the cartridge.

Understanding the meaning of the word “toner” and the main problems that arise in the operation of the printer when it is not available will save nerve cells and easily troubleshoot the problem.

Copy counter malfunction

Message appears if the number of copies printed from the previous cartridge has not been reset.

It is easy to fix the problem if the side cover of the printing device is equipped with a window for reading copies. The window is sealed with opaque tape. Now the light on the photocell that counts the number of printed sheets does not hit and the printing will be stopped only when the ink powder is fully used.

If there is no such window, you can reset the counter by changing the settings of the printer itself:

  • Click on the “User Settings” button.
  • Click OK.
  • We are waiting for the message “Reset toner counter” to appear on the monitor, click OK.
  • In the settings menu, we look for, using the arrows, the “Enable” item, click OK.
  • Counter reset to zero.

Important! It is necessary to carry out work after a complete stop of the MFP.

What is toner

The ink with which a printing device makes prints on solid media is called toner. In appearance, the toner is black or colored powder. They are used to fill the cartridges that are used in the work of laser printers. The substance is heated in a container to a temperature of 200 degrees, begins to melt and printed characters appear on the paper.

Black powder is used in monochrome models. In full-color, when mixing paint of black, yellow, pink and blue shades, a color picture, photo or text is obtained.

The powder in the cartridge has run out

It is easy to understand this: every day the print quality deteriorates, white streaks appear, the text is colored unevenly, and colors change in the color picture. If such signals appear, the cartridge should be replaced or refilled.

Advice! A little trick will help you finish urgent work. Carefully remove the container with the powder from the MFP, shake it several times and shake it from side to side in the longitudinal direction. Such actions will allow you to print up to two dozen copies.

What does it mean there is no toner in the printer?

The reason is that the printer does not “see” the toner sensor curtain jumping in its window (see the article on the mechanism of the sensor). There are five simple options for the cause of this problem:
1. The toner cartridge locking knob is not turned fully. The window at the end of the handle should be located exactly opposite the hole in the printer body, behind which is the optocoupler of the toner sensor. Press the handle all the way.
2. Toner has adhered to the white curtain that appears in the window, which makes it stop reflecting the light of the optocoupler. The shutter must be cleaned of toner for the sensor error message to disappear.
3. In the printer, where the purchased cartridge has already been, there was a starting one again. All junior printers, starting from the summer of 2004, are supplied with starter toner cartridges, which do not have a toner sensor (see above), but instead just a piece of foil is glued on. Such a cartridge can work normally in the printer only from the very beginning. If it is present, the printer calculates the toner consumption only by the formula and when it reads to the end, it requires replacing the cartridge. After that, you need to install a purchased cartridge in the printer, which has a toner sensor. As soon as such a cartridge enters the printer, it enters the toner sensor control mode, and if after that the starter cartridge is inserted into it again, the printer, not seeing the working sensor, will display a toner sensor error.
4. The size of the window is too large. A situation is possible when the window behind which the white curtain is located is too large and therefore the optocoupler cannot correctly focus the reflection from the curtain and obtain a stable response. The situation can be corrected as follows: it is necessary to glue the window from above with black, non-shiny tape so that the height of the slot is no more than 4mm:

The wrong photo print cartridge is installed. At the bottom of the photo cartridge is a small metal pin (or multiple pins) that fit into slots in the metal plate located on the right side inside the printer.

The pins can be installed in different positions. It is the position of the pins that determines the “compatibility” of a particular photo cartridge with a particular printer. If a photo cartridge of the wrong type is inserted into the printer, then the cartridge is installed in the printer at the wrong angle and the window of the toner sensor simply does not hit against the optocoupler. The pin, in principle, can be rearranged, but for this it is necessary to disassemble the cartridge, since it is impossible to take it out: there is a hat at its end that does not allow pulling it out. Therefore, somewhere this reason can also be attributed to complex options. However, you can unscrew the metal plate inside the printer, the one against which these metal pins rest, then you can install a print cartridge from any printer of the 3000 or 5000 series into the printer.

Now the “difficult” options are on their own. After removing the toner cartridge and holding it in the same position as it is in the printer, rotate the gear from the bottom with your finger. The white curtain should periodically move up from the window for a short time. If this does not happen, then there is a mechanical problem.
1. The sensor lever is jammed. The white curtain is stuck in either the up or down position. Try manually (for example with a needle) swinging the curtain up and down. This can usually be done without disassembling the cartridge.
2. The stirrer inside the toner cartridge has come off. When the gear rotates, the agitator does not rotate inside the cartridge, which is why the shutter does not jump either. Obviously, to restore the working capacity, it is necessary to disassemble the cartridge and restore the rotation of the mixer.
3. The cartridge is filled with magnetic toner. We have heard about such a problem only in relation to a black cartridge, which they tried to fill with black magnetic toner from b / w printers. Such a toner, which is in the cartridge, “forever” attracts the magnet, which is why the curtain goes up from its window, giving a permanent false on the sensor. The solution is obvious. use a non-magnetic toner, thoroughly cleaning the inside of the toner cartridge from the remnants of magnetic powder.

The new C3000 and C5000 series printers have a toner sensor located in the photo cartridge. From the outside, it is visible as a rectangular window located at the end of the photo cartridge on the side where the locking handle of the toner cartridge is located:

This window is covered with a special shutter when the toner cartridge is detached from the photo cartridge (in the picture below, it blinks red, but in reality this shutter is black):

So, the toner sensor error can occur on these printers because the shutter did not go up when the toner cartridge handle was closed. In this case, the optocoupler will not “see” the reflecting sector moving behind the window, which triggers the optocoupler to operate. Accordingly, close the handle of the toner cartridge all the way or if this does not help, take other measures so that this shutter goes up.

NNCXV.INFO 2021