Why Does The Printer Strip When Printing Epson

Why Canon printer prints in stripes and what to do?

does, printer, strip, printing

None of the printers released in the history of the printer is immune to the appearance of light, dark and / or color stripes during printing. No matter how technically perfect this device is, the reason lies either in the end of ink, or in the malfunction of any of the components.

Possible reasons

What to do?

You can remove streaks during printing using the following methods. It is more advisable to adhere to such a routine.

  • Checking the ink (toner) cartridge is full. Open the printer properties to check the ink levels. In Windows 10, give the command “Start. Control Panel. Devices and Printers”, select your device and run one more command: right-click on the icon of the device under test. “Printing Preferences”. The software tool for setting print options and troubleshooting problems opens. On the “Service” tab, use the “Special Settings” utility. all information will be shown, including a report on the possible toner level (or ink levels). If the toner level (or ink levels) drops to the minimum (or zero) mark, you will need to refill or purchase a new cartridge (or new cartridges).
  • Check to see if the cartridge is leaking. Lay on a napkin or paper and shake it. Spilled ink or spilled toner indicates a leaking cartridge, which must be replaced. If the sealing is intact, reinstall the cartridge. most likely, it is intact and functional.
  • Make sure the inkjet cable is intact. It should not be pinched anywhere. Not every user will be able to assess his condition, as well as change it. A faulty loop is replaced at the office equipment service center.
  • Check air filters. A clogged filter with ink stuck in is poorly or NOT allowing air to pass through at all. Darkened streaks appear on the sheet when printing. Change the filter to a new one.
  • If white stripes with blurry fonts and graphic lines appear that make reading difficult (eyes are overstrained), the encoder film must be cleaned. It is a semi-darkened tape along the print carriage. The belt is cleaned with a non-abrasive detergent. DO NOT use solvents. this will erase the markings. Let’s use pure alcohol or vodka without sugar additives.
  • A dirty or air-bubbled printhead needs cleaning. In Canon printers, the print head is built into the cartridge. If head cleaning is not possible, the cartridge must be replaced. Head cleaning is performed in several steps. You need to insert paper into the receiving tray (you can use it, with an empty second side), enter the already familiar settings tool on a PC or laptop, and launch the “Printhead Cleaning” utility. After the printer tries to clean this head, run the Nozzle Check utility and then Nozzle Check. If the attempt is unsuccessful, repeat the same operations up to two times (the whole cycle). Print a test page after 3 hours. you will see immediately if the printer is striping.

Cleaning the channels of the printing device is done only manually. With the ineffectiveness of complete cleaning (software and physical), suspicion falls on completely inoperable parts that need to be urgently replaced. Canon and HP printers are good in that not the entire printing mechanism is completely replaced, but only the cartridge.

Helpful hints

DO NOT use acetone, dichloroethane, or water to clean the printheads. Water should not get on it. a wet head prints with streaks, and synthetic solvents, softening plastic and other polymers, will simply ruin its coating. It is recommended to use either a special cleaner (sold in the office supplies department), Recommended by manufacturers, or a cleaner for regular glass.

In addition to checking the ink level, if your printer uses black and white toner, it is recommended to check the level of used powder in the secondary compartment of the cartridge. The coloring matter in such a powder is almost completely absent, which means that it will not be possible to use it again for printing, and the cartridge is designed in such a way that it will NOT wake up back into the hopper of unused toner. And in this case, the cartridge must also be replaced.

DO NOT transport or move the printer from place to place unless absolutely necessary. The carriage in the print head sometimes moves from this. Using a separate utility in the Canon service settings, the carriage calibration is restored.

Use of non-proprietary ink. due to the high cost of proprietary (recommended by Canon), users are forced to regularly clean the nozzles and other moves of the print head. The fact is that “third-party” ink sometimes dries several times faster. Office printers, since they often and in large quantities print all kinds of documents, and do not face the problem of ink drying (except when the cartridge has lost its sealing). For a home printer that can be idle for up to several weeks, ink drying is one of the most common problems.

Why the printer prints stripes or the color completely disappears, see below.

Why does the printer print in stripes? How to fix them?

Desktop printers consist of complex devices, and when they issue printed sheets in the office or at home, showing disgusting stripes along the pages, the user wonders for a long time why the printer prints stripes, and will do this until he learns to diagnose the breakdown on his own.

Inkjet Principle

Inkjet devices work by heating tiny nozzles with an electric shock, reshaping the ink and leaving marks on the page. When the printed sheet contains gaps or horizontal lines, it is most likely clogged nozzles in the printheads.

Why does an inkjet printer print in stripes, even when the printer was not working. Inkjet devices do not tolerate downtime and it may take several printer cleaning cycles to pierce dried ink. If exit defects have vertical lines, the Printhead may need to be rearranged. Both cleaning and regrouping use additional consumption of installed ink, especially if the equipment requires deep cleaning or several adjustment cycles.

Laser toner or drum cartridge

Laser printers create a complete printed page at a time by transferring toner onto paper from a rotating drum. The drum is either included with the toner cartridge or installed as a separate unit. In any case, scratches on its photosensitive surface may cause streaks or lines to appear, which can be seen when the cartridge is removed.

Toner consists of a mixture of shredded plastic and dyes. To bond it onto paper, laser printers use a heating element called a fuser to melt toner as the paper moves through the rollers in the fuser. When vertical lines appear on the printed sheet, you need diagnostics that are easy to perform using the special defect bar template supplied by the printer manufacturer for the corresponding equipment model.

This document identifies the source of marks along the page by their location along with the position of the rollers and other components of the printing mechanism, and easily identifies why the printer prints stripes. Certain manufacturers Provide this service manual to technicians only.

Typical Epson Printer Errors

If the Epson Corporation printer did not print the correct “nozzle check” without gaps, head cleaning with the Epson Corporation Maintenance Utility did not work and the problem still persists even after installing new ink cartridges, it looks like the print head is clogged.

This usually causes the printer to print poorly and therefore allows the ink to dry on the print head itself. Poor quality aftermarket inks can also contribute to this breakage, although this is very rare. It is important to note that many printer manufacturers use cheap disposable printheads attached to their cartridges.

Epson printheads are part of the printer itself, allowing Epson to produce much higher print quality than most inkjet printers.

Cleaning the Epson Printheads

Epson ink is very expensive and excessive head cleaning depletes the Epson ink cartridge in no time. The best way to save your printer. Use expensive but high quality ink after purchasing the printer. If you do not understand why your Epson printer prints in stripes, it is best to follow a simple cleaning procedure.

How to clean the printer

  • Turn on the printer, and if the product does not print, make sure the ink light on the front of the printer is blinking, otherwise the cartridge needs to be replaced before proceeding.
  • Check for paper in the tray and add paper if necessary.
  • Click on “Start” and “Devices and Printers” to see a list of all installed printers, and then double-click on the Epson printer. Double-click “Print Settings” to open the “Print Settings” Dialog Box and then no need to ask a question. Why the printer prints with Epson stripes, and select the Maintenance tab and click Head Cleaning. Alternatively, you can right-click the printer icon in the taskbar and select the Head Cleaning option. These options may differ slightly depending on the version of Epson software installed on your computer.
  • When prompted to start the cleaning process, click “Start”. For some versions of Epson software, you must click Next to continue. Wait for the head cleaning process to complete. This process can take several minutes. Turning off the printer during the cleaning process can permanently damage the device. The printer power light that blinks during the cleaning process will stop blinking when the cleaning process is complete.
  • Click Customize Nozzle Check Pattern, and then click Print. The printer prints a number of staggered deadlines.
  • View the printed nozzle check sample page. If the template shows continuous timelines with no gaps or weak printing, the cleanup process was successful and you can click Finish. If the template contains spaces, and it is not clear why the printer prints in stripes, press “Clear” again to restart the process of cleaning the printheads.

Each Epson owner will eventually face the problem of poor printing, but in order to prevent this, you must adhere to simple rules:

  • Print at least one test page every 3-4 days.
  • Use only high quality ink.

Reasons for poor print quality in Canon printers

Whatever the style of Canon printers, but if the user chose this model, he needs quality printing. Why the printer prints in Canon stripes right after the first ream of printed paper has been asked by many users. Indeed, the printer may leave streaks or gaps on printed pages.

This can happen for several reasons:

  • Low ink levels.
  • Damaged cartridge.

In any case, it is not dangerous, and there are ways to troubleshoot and set up your Canon printer properly. Most Canon printers have a built-in printhead alignment test.

Why does the Canon printer print in stripes if it is still quite new? Even newer inkjet printers have such problems due to clogged nozzles. The software of all inkjet printers can successfully cope with this problem even for non-advanced users.

  • Open Canon software on your computer and click the Maintenance tab at the top.
  • Then click Align Printheads and Align Printhead. The printer will print a test letter with a row of colored rectangles.
  • Press “Manual Head Compatibility” on the screen to print the second test sheet. The printer will try to print with different settings, choose the one that works best and has the least stripes, and enter its number into the Canon software.
  • Click OK and try printing a different page. Why does the printer print with Canon stripes even after cleaning? You may have to repeat the process several times to correctly calibrate the printheads.
READ  Samsung TV does not connect to WI-FI router

HP printers. Prevent smudged printing

To ensure clear and normal performance of the Deskjet printer and to prevent streaks on printed sheets, the cartridge must be mechanically cleaned. What to cook for:

  • 5-6 cotton swabs or any clean pieces of soft, lint-free material that won’t leave fibers behind when wet.
  • Clean bottled water to moisten tampons.
  • Sheets of paper or paper towels for storing cartridges while cleaning.
  • Step one: remove the cartridges and unplug the power cord from the back of the product. Remove both cartridges and place them on the sides on a piece of paper. Do not leave ink cartridges outside the printer for more than 30 minutes. If the cartridge is left on for too long, the ink will dry out and the cartridge will become unusable.
  • Step two: clean the cartridge. Dampen a clean cotton swab and squeeze out excess water. Hold the black cartridge with the nozzle facing up. Use a swab for wiping, while absolutely not wiping the contact plate of the nozzle. Inspect the cartridge and determine if any residue remains. To do this, you need to keep it in the light and tilt at an angle. If you do not understand why the printer prints with black lines and there are traces of dust, dirt or lint, repeat the procedure to remove them. Repeat the same procedure to clean the color cartridge. Always use a new cotton swab for each cartridge to avoid transferring debris from one cartridge to another.
  • Step three: reinstall the cartridges and lower the cover. Plug the power cord into the back of the printer.
  • Step four. Check your printed result.

Why does my HP printer print in stripes when even mechanical cleaning does not work. To do this, you can use the automatic printer cleaning.

  • Click “Start” and “All Programs”.
  • Find your HP Deskjet printer in the list and click it to open the printer menu. Alternatively, you can click the HP Deskjet icon on the desktop or taskbar.
  • Go to the Printer Services tab and click Clean Cartridges. Click “Clean” to clean the printer and print a checklist. Examine the test letter and click “Finish” if the print quality is good.
  • If not. Press “Intermediate cleaning” to perform a deeper cleaning. If the print quality is good, click “Done” and then click “Prime”.
  • Examine the last test letter and click “Finish”.
  • If print quality deteriorates after interim cleaning, you may need to replace ink cartridges.

Common laser printer problems

Unbound toner that penetrates the interior of the laser printer may end up on the rollers or other moving parts and transfer to the print output in stripes, tracks or lines. Many rollers form a distinctive “tire mark” pattern along each sheet in the direction the paper travels through the printer, which is why a laser printer prints in stripes. To eliminate THESE defects, a preliminary analysis is required:

  • Trace the source of loose toner, it could be a leaky cartridge damaging the machine, or trying to reprint a toner page that melts at a lower temperature than the Installed Printer. In addition, roller tracks can cause dirty printing. When loose toner gets out of the cartridge and into the mechanical parts of the printer, it can get dirty on the rollers that move the paper through the machine.
  • Depending on whether vertical defects are visible in black or white. Printed marks or voids when printing, it can be assumed that the problem is caused by an empty cartridge, a scratched drum, or poorly distributed toner.

Dirty rollers can cause horizontal print defects and marks, which appear at regular intervals. Dropouts and non-duplicate marks can occur due to the same issues that cause vertical defects, including laser contamination and toner cartridge malfunction.

Fuzzy laser printer

If the page has fuzzy prints, letters or graphics that are not as sharp and clean as usual, the problem is probably not with the printer, but with the paper. Fuzzy printing usually occurs when printing on slightly damp paper. The paper absorbs moisture from the air and it can be damp, which is why Canon prints in stripes. You need to print on freshly unpacked paper. If the page still has a fuzzy white line where printing is weak or absent, then the Transfer Corotron may be dirty.

Open the printer and look closely at the Transfer Corotron and follow the procedure described in the user manual to clean it. Most small printers require the corotron wire to be gently wiped clean with a special cleaning tool. These wires are very thin and delicate, so you need to be very careful when cleaning the wire, otherwise it may be damaged.

Sharp white laser lines

Why does the printer print in white stripes and the page has a well-defined white line, there may be a lock in the drum unit that prevents toner from flowing to the roller. The developing roller usually has blades directly above and below it, which remove excess toner, and a small piece of damp toner can block the gap between one of them and the developing roller.

Some printers are prone to this problem and come with a small cleaning tool that slides along the gap between the blade and the developing roller. If instructions are given by the manufacturer on this problem, they must be followed. If instructions are NOT specified and the developer roller is visible, you can release the blockage by gently sliding the corner of the sheet of paper between the developer roller and the blades. If the developer unit is a detachable part of the user, remove it from the printer and shake it from side to side.

Variable density per page

If the print density (blackness) varies across the page, and it is not clear why the printer prints in stripes, then it is best to seek professional advice online. Although it can be caused by several factors. In general, when toner runs out, it may not flow as freely as in a full hopper, so some areas of the page may receive less toner than others, resulting in a change in print density on the page. To overcome this, fill the toner hopper.

If the printer uses toner or a cartridge, remove the cartridge from the printer and hold it horizontally and shake it side to side four or five times to redistribute the toner. If one side of the page is always lighter than the other, the printer might not be straight. Make sure the printer is on a level surface, otherwise toner may gradually move to one end of the toner hopper. Shake the toner hopper to redistribute it.

Another prerequisite, when one side of the page is lighter than the other, might be light entering one side of the printer body. Most printers are NOT completely opaque, and if they are located near a strong light source (lamp or window) some light may be produced affecting the photoreceptor. If the printer is close to a light source, move it to a different location.

Gray print

If the font is gray instead of black, there are two possible reasons: the print density setting and the photoreceptor. Most small laser printers have a print density control, either a knob or a control panel setting. Increase the print density to make the print more “black”. As the photoreceptor wears out, it holds less charge, transfers less toner from the developer to the paper, and therefore causes gray prints.

To overcome this drawback, it is necessary to increase the print density setting until the photoreceptor does NOT require replacement. If the problem is particularly acute, it may be worth replacing the photoreceptor prematurely.

Black pages

In some printers, a black page may occur when the charger is damaged or incorrectly connected. Examine the charger corotrons to see that it is not broken. If the corotron charger is broken and included with the cartridge or photoreceptor, replace the cartridge or photoreceptor with a new one.

If it is NOT broken or not visible, try removing and reinstalling the cartridge or photoreceptor, as the electrical contacts between the plug-in unit and the main body of the printer may not be properly connected.

If splitting occurs on the page so that there is a horizontal gap in the image separating graphics and characters, the printer controller has probably made a mistake. This can happen by accident, in which case the only solution is to reset (turn on and off) the printer or reappear. If the problem occurs frequently, the prerequisite is probably a faulty printer controller or printer controller memory.

The timely methods of cleaning the printheads presented in this section mainly allow you to independently restore the correct operation of the devices, however, there are times when normal operation will be restored only after replacing the principal components of the printer.

Why does the printer print with stripes and what to do?

Almost every printer user sooner or later faces the problem of printing distortion. One such disadvantage is stripe printing. From the material of this article you will learn why this happens and what needs to be done to solve the problem.

What is the cause of printer malfunction?

If the printer begins to strip after some time from the date of purchase, it is another matter. In this case, it is not at all necessary to replace it with a new one. First you need to understand the possible reasons, because often the problem is completely solvable. Streaks on paper during printing can occur for several reasons. In this case, the reasons may depend on the type of the printer itself.

Inkjet

An inkjet printer can strip when:

  • Clogged nozzle;
  • Contamination of the encoder disk;
  • Improper ink supply;
  • Poor ink quality;
  • Calibrating printheads.

Drying of ink is a probable cause of a print defect. This happens when the printer is not used for a long time. In addition, the device will strip when printing when air enters the print head. Sometimes the cause of the problem is the blockage of the ink plume of the CISS. The product may print poorly with poor quality ink. Another prerequisite may be shaft deformation, which is typical with prolonged use of the printer. And also defects in printing may appear when the ribbon or sensor is dirty.

READ  How to Connect Printer to Laptop with Wire

However, you should immediately throw away the equipment, because you can identify the problem and fix it yourself. Often, the cause of a defect that has appeared can be determined by the type of stripes, namely:

  • Multicolored or white stripes indicate improper ink supply;
  • Vertical line breaks indicate printhead misalignment;
  • White stripes at an equal distance from each other occur when the encoder is clogged.

Laser

The reasons for the appearance of streaks when printing on a laser printer are as follows:

  • Out of toner;
  • The drum is worn or damaged;
  • Waste toner hopper full
  • There is mechanical damage;
  • There are problems with the metering blade.

As with inkjet printers, sometimes notions of the cause of a print defect can be made by looking at the stripes themselves. For example, white vertical stripes that grow with each new letter indicate the need to refill the cartridge. Vertical stripes of different widths indicate mechanical failure of the device. If the printer leaves black spots or dots on the paper during printing, the waste toner box is full. Black dots and a broken line around the edge of the sheet indicate that the drum is worn out. When dark streaks or faint vertical streaks appear on the pages, the problem lies in the metering blade.

The cause of the defect may lie in the deterioration of the magnetic shaft. He is responsible for applying the powder to the drum. During use, the toner acts on the coating of the magnetic roller. If it is frayed, the printer prints pages with white, uneven stripes. In addition, the color of the text also changes. Instead of black, it turns gray, and the pattern fill is uneven. However, the magnetic shaft often has to be changed along with the dosage blade. It also causes printing defects.

What to do?

To solve the problem, you need to build on the type of printer.

Inkjet

Inkjet printers are refilled with liquid ink. When they end, you can notice a change in shades. For example, instead of black text, the printer prints blue, horizontal spaces, or white stripes dividing letters in 2. Sometimes the printer even prints pages with transverse stripes over the entire surface of the sheet. Such a problem indicates an overflow of the hopper or the need to replace the squeegee.

In the second cases, it is necessary to inspect the integrity of the thermal film. Toner should spill out of the cartridge. It’s easy to check: you need to take out the cartridge and shake it slightly. If this causes your hands to turn black, you will have to replace the toner with a new one. Otherwise, you won’t be able to fix the problem. However, before doing anything, you need to consider: the ways to fix the problem in inkjet and laser printers are different.

First you need to figure out how to self-eliminate the defect of inkjet printers.

  • Checking the ink level. If the inkjet device produces stripes when printing, you must first stop printing and refill the cartridges. The problem cannot be ignored, without paint it will NOT be possible to carry out a nozzle test. In addition, a lack of ink will cause the nozzles to burn out. To do this, find software, install and run the program. Next, open a tab with a drawing of ink capsules. It can be named by different names (“Estimated Ink Levels”, “Printer Ink Levels”). Use the printer control panel to diagnose ink levels. A visual assessment will help you understand which ink needs to be replaced. Usually, when the level is critically low, an alert icon appears in the form of a yellow triangle.
  • Diagnostics of CISS. If after refilling the cartridge nothing changes, stripes reappear on the paper when printing, you need to check the CISS (continuous ink supply system). It is important to make sure not to pinch the Ink Trail. If the system is not pinched, check the air hole filters. If they are clogged, their bandwidth is compromised. Remove dust and dried paint. If they become unusable, you need to replace them with new ones.
  • Nozzle testing. If after checking there are no problems with the ink tank, but the printer continues to print with stripes, you need to test the nozzle. To do this, go to “Start”, then select “Devices and Printers”, find your printer, press the right mouse button and select “Printer Properties”. In the window that opens, click on the “Settings” item. After that, go to the “Service” tab, and then select the “Nozzle check” item. However, the test pattern may vary depending on the type of printer. Modern models predict nozzle testing on the device itself. The verification algorithm depends on the model, it is indicated in the instructions for a specific product.
  • Cleaning the printheads. Inks used in inkjet printers dry faster than laser-type counterparts. With prolonged simple appearance of stripes during printing is not uncommon. Ink can clog nozzles after 2 weeks of inactivity. Sometimes the print head clogs up in 3 weeks. To solve the problem, the installation program has a special utility “Cleaning the printheads”.

This procedure saves ink consumption. If you forget it, the ink will start flushing the nozzles on its own during subsequent printing, consuming the cartridge. The cleansing procedure can be carried out 2-3 times at once. After that, you need to let the printer cool down, and do not touch it for 1-2 hours. If this does not help, then the head will have to be cleaned manually.

If the nozzles or printhead nozzles are dry, you can try to solve the problem programmatically or physically. You can try to soak the cartridge. To do this, take it out, put it on a napkin on the table. With a little effort, it is pressed against the table with nozzles, trying to press with fingers on both sides. If this does not help and the paint does NOT come out, you need to try a software solution to the problem. To do this, open the “Printer Properties” and select the “Maintenance” tab. Next, alternately select the first 2 tabs (“Cleaning” and “Deep Cleaning”).

  • Cleaning the encoder tape and disk. When the printer prints pages with different strip widths, the encoder disc must be cleaned. The desired part is located on the left of the paper feed shaft, it runs along the movable carriage and is a transparent plastic film with markings. During the operation of the printer, these markings become covered with dust, ink may remain on it, which will dry out over time. In total, the sensor does not see them, and the paper is positioned incorrectly. To solve the problem, you need to wipe the disc with a soft cloth, soaking it with a special cleaning agent or detergent preparation “Mister Muscle” for cleaning windows with ammonia. After that, you need to wait about half an hour so that the treated surface is completely dry. Do not use acetone: this erases the markings. During cleansing, you need to be extremely careful. If the strip comes off the mounts, half the printer will have to be disassembled to put it back in place.

Laser

Laser printers are not only color, but also gray and white. In the overwhelming case, the appearance of streaks on the print is explained by the state of the used cartridge. Typically, any new device of this type contains cartridges with a minimum amount of powder. It ends faster.

    Replacing the toner. If the color changes during printing and white streaks appear in the middle of the text, replace the cartridge. It is useless to take out and shake the toner trying to print a few more pages. It will not help, not worth knocking the cartridge on the table, floor. From this, mining will begin to pour out of the sump. Waste printing shortens printer life.

You need to replenish or replace the cartridge if streaks appear in the middle of the sheet. If the stripes are dark and sinuous, this indicates a poor quality of the powder used. When the toner level has not reached the critical mark, pay attention to the supply system. In this case, you cannot avoid contacting the service center.

  • Replacing the drum unit. The imaging drum of laser printers has a coating that is sensitive to optical radiation. During use, this coating will wear off and the quality of the printed pages will suffer. Black stripes appear on the left when printing, they DO NOT pass after replacing the toner and become wider. Removing them will not work: you will have to change the drum unit. If you delay the moment of contacting the service, other elements of the device may suffer.
  • Damage to the cartridge if dropped. If the problem appears after accidentally dropping the cartridge, the powder-trapping rubber seals may NOT resist impact. As a result, the powder will pour onto the baking sheet, leaving streaks and stains on it, not only on the side, but anywhere. You will NOT be able to do anything with the toner: you will have to buy a new one.

To eliminate the problem of damage to the cartridge, remove it from the printer, inspect for cracks and loose parts. In addition, the places where the bolts are screwed in are inspected. Then they shake slightly, slide the curtain near the shaft and see if the powder is poured. If everything is in order, inspect the mining bunker.

Few people thought about the fact that when this compartment is overfilled, some of the powder gets out. This results in wide black stripes on the pages. To prevent this, you must remember about prevention. Cleans this compartment every time you refill toner yourself.

  • Software problems. The streaking may be caused by a software malfunction on the device. This could be due to a power outage, user damage, or viruses. If the stripes after other manipulations continue to decorate the pages when printing, you will have to reinstall the driver. It is usually included with the device. If the disc is damaged, you can download the driver from the official manufacturer’s website.

Helpful hints

As for the ink, sooner or later it will run out and the cartridge will require replacement. However, the following simple guidelines will help you extend the life of your printing device:

  • The sooner the problem is identified, the better; pulling on the latter will shorten the life of the printer;
  • You need to check the ink level constantly, as well as. Make sure that they DO NOT dry out;
  • You need to clean the waste bin every time you refill toner; it must not be allowed to overflow;
  • If the stripes consist of small dots, you need to refill the cartridge and install the blade correctly;
  • If streaks appear in the same part of the page, refill the cartridge and check the shaft for a foreign object;
  • Do not pour a lot of powder into the toner hopper, this will not increase the number of printed pages;
  • If on an inkjet printer both cartridges (color and black) are filled with paints, the nozzle and printhead diagnostics DOES NOT reveal the problem, the reason lies in the misalignment of the head;
  • Use a wooden stick to clean the blade, being careful not to cut yourself.
READ  The Printer Writes No Toner And The Cartridge Is Full

The following video tells you what to do if the printer is lining.

Printer strips

Signs: the presence of streaks in the printed image

Possible reasons :. Air in cartridges or plume;. The train is transmitted;. One or more cartridges do not work;. Clogged print head;. Poor quality ink.

Solution options:. Pump air and make sure that the CISS is in working position and installed at the correct level;. Visually check the location and laying of the ink plume;. Cleans the print head using the driver;. Visually inspect the cartridge (whether it is sealed, and whether ink leaks from the side of the valve when lifting the ink cans), if there are problems with it, then the cartridge must be replaced. If it’s ink. Replace them completely.

Printer strips

Notice that your inkjet printer is starting to strip badly? Stripes on printed photos and documents do not color them at all. Common problem, but solvable.

So why does the printer strip? There can be many reasons for this:

  • Air in the printhead, cartridges, or ribbon cable (obstructs ink flow)
  • Squeezing the train;
  • System leaks;
  • Breakage of one or more cartridges;
  • Clogging of printheads;
  • Base ink.

What to do if the printer slashes when printing? Naturally, the way to fix the problem depends on the cause. Possible solutions to this issue:

  • If the problem is the paint. Replace it completely;
  • Make air circulation, install the NPC system at the level with the printing apparatus;
  • Inspect the air holes, check if they are open, if paint reaches the cartridges;
  • Clean the printing mechanism several times and leave it for more than an hour;
  • Check the location of the ink plume, excluding its pinching;
  • Calibrate the printheads; inspect the cartridges (how tight they are, and whether the paint leaks), if there are problems with them, then the cartridges should be replaced;
  • Make a nozzle test, perform a cleaning procedure.

Signs: the presence of streaks in the printed image

Possible reasons :. Air in cartridges or plume;. The train is transmitted;. One or more cartridges do not work;. Clogged print head;. Poor quality ink.

Solution options:. Pump air and make sure that the CISS is in working position and installed at the correct level;. Visually check the location and laying of the ink plume;. Cleans the print head using the driver;. Visually inspect the cartridge (whether it is sealed, and whether ink leaks from the side of the valve when lifting the ink cans), if there are problems with it, then the cartridge must be replaced. If it’s ink. Replace them completely.

Printer strips

Notice that your inkjet printer is starting to strip badly? Stripes on printed photos and documents do not color them at all. Common problem, but solvable.

So why does the printer strip? There can be many reasons for this:

  • Air in the printhead, cartridges, or ribbon cable (obstructs ink flow)
  • Squeezing the train;
  • System leaks;
  • Breakage of one or more cartridges;
  • Clogged printheads;
  • Base ink.

What to do if the printer slits when printing? Naturally, the way to fix the problem depends on the cause. Possible solutions to this issue:

  • If the problem is the paint. Replace it completely;
  • Make air pumping, install the NPC system at the level with the printing apparatus;
  • Inspect the air holes, check if they are open, if paint reaches the cartridges;
  • Clean the printing mechanism several times and leave it for more than an hour;
  • Check the location of the ink plume, excluding its pinching;
  • Calibrate the printheads; inspect the cartridges (how tight they are, and whether the paint leaks), if there are problems with them, then the cartridges should be replaced;
  • Do a nozzle test, perform a cleaning procedure.

Reasons. why the printer stripes during printing

Defects in printing of an inkjet or laser printer can appear during operation. The appearance of stripes indicates a failure or malfunction of the components involved directly in the process of applying the image to the paper.

The cause of the problem

The printer will strip when printing in the following cases:

  • For inkjet Canon, Epson, the problem is typical with a dry microdroplet head, lack of toner or malfunction of the ink supply system;
  • In laser, the reason lies in the end of the toner and drum, which has reached the useful life.

In both situations, we are talking about the need for service or replacement of defective parts. These tasks can be solved independently, but if you are interested in a full inspection and maintenance of your printing device, we recommend contacting the service center. Now let’s try to figure out why the printer is striping, and what can be done, and not by Contacting the service.

Inkjet printers

Many users ask a question related to malfunctions when the printer strips Epson, Canon and other models. There are several issues that are discussed below in more detail:

  • The need to clean the Epson head;
  • In a failed ink supply system;
  • And in the ending cartridge.

Causes and solutions

When it comes to Canon, Epson inkjet printers, the device will strip after a long idle time. This is also typical for low-quality ink or when foreign elements have got into the container, got into the head and needs to be removed. At home, you can only try to clean the nozzles using standard products.

The problem of the appearance of stripes of different colors may be associated with a malfunction of the continuous ink supply system, in this case, preventive maintenance is also necessary, associated with cleaning and correct connection.

In the case of using cartridges, the ink in the reservoir of one of the colors can be trite, the last portion on Epson can be issued in stripes. In this case, replacement or refilling of the cartridge is required.

This pattern, associated with uneven penetration of inks of different colors, is quite normal for Epson and other inkjets if you printed images only in red or blue tones. The most used ones run out sooner. When printing photos, the ink in the tube is consumed at approximately the same rate, although there may be exceptions, sometimes streaks due to low-quality paper.

Elimination of the problem

What to do to fix the problem with a clogged head:

  • Print a test page. This can be done from the Windows Control Panel. Click the Devices and Printers tab, select your devices, click Printer Properties and print a test page. This will help determine why the Epson printer is striping.
  • The nozzle cleaning procedure can be repeated several times if there is reason to suspect an ink supply problem.
  • In this case, the device displays each color in the form of stripes, which test the condition of the head nozzles. If a certain color is missing, and everything is working fine, then we are talking about a problem with the cartridge. If the color comes out in parts, and the problem repeats on the second colors, most likely the head is clogged.
  • It is useful to clean the head several times after each rather long break in work. This can be done as follows: hold down the ink drop indicator button for 3 seconds. Device to clean the head. Repeat the procedure 2-3 times and print a test page.
  • If there are no blanks in the test, the product is ready to print. If all else fails, you need to replace the cartridge or check the CISS.

In SEPARATE cases, mechanical cleaning of the device head is required. This task can only be completed with the skills. If there is a suspicion, in order to avoid more serious repairs or the purchase of a new device, we recommend visiting the wizard.

Printer print head

If there is a problem with the cartridge, you just need to install a new one. over, it is better to avoid refueling if there is a possibility of clogging. The cartridges are non-separable and cannot be repaired. The CISS system should be inspected for clogging and the reasons for the discrete ink supply, if necessary, repair or replacement is carried out.

Please note that nozzles may become clogged when using the Epson L805 and Lomond branded office paper. In this case, it makes no sense to repair the Epson L805, just change the paper.

Laser devices

In laser devices, printing with defects is observed in several cases:

  • When the toner runs out (this is typical for HP and Canon)
  • If the drum is used up;
  • With pollution;
  • In a long-term device, in which the printing mechanisms have already worked out their useful life.

If a Canon or any other printer strips, you can try to correct the situation by shaking the cartridge. Why does it help? Due to unevenly distributed toner residues in the tube cavity. True, this method will not always help and not for long, but HP, Canon can be started. In SEVERAL cases, the output quality can be improved by cleaning the drum and other components with a brush. This requires opening the device and cleaning.

radical methods include refilling the device with toner. If there are streaks in this case, we recommend replacing the drum. It is advisable not to do this on your own, but still consult with a specialist, who can eliminate hidden breakdowns.

Maintenance of modern printer devices is simplified as much as possible. Many functions and features can be carried out directly by the user, including when strips and prints with defects. It helps to restore the performance of HP, Canon, Epson. Using simple instructions, you can inspect your printing device even without working skills.